Comparison · Beginner · 3 min read
Electronics Connectors
JST, XT60, Terminal Blocks and Headers
By Geekobot Learning Team · Updated 24 Oct 2026
On this page
Pick a connector by current, pitch and how often it will be unplugged. For signals and sensors use 2.54 mm headers or JST connectors (XH 2.5 mm, PH 2.0 mm, SH 1.0 mm for Qwiic and Stemma QT). For battery and motor power use XT30 or XT60. For secure field wiring use screw terminal blocks. Measure the pin pitch with a caliper before buying.
Key specs at a glance
- 2.54 mm header / Dupont
- Signals, breadboards, modules; about 1 to 3 A
- JST-XH (2.5 mm)
- Balance leads, small power; about 3 A
- JST-PH (2.0 mm)
- Small LiPo cells, sensors; about 2 A
- JST-SH (1.0 mm)
- Qwiic / Stemma QT I2C cables; about 1 A
- XT30 / XT60 / XT90
- Battery power: about 15 to 30, 30 to 60, 90 A
- Screw terminals
- 5.08 or 3.5 mm pitch; secure field wiring
Identifying common connectors
| Connector | Pitch | Current (approx.) | Where you see it |
|---|---|---|---|
| Pin header / Dupont | 2.54 mm | 1 to 3 A | Arduino shields, sensor modules, jumpers |
| JST-XH | 2.5 mm | 3 A | LiPo balance leads, 3D printer fans and endstops |
| JST-PH | 2.0 mm | 2 A | Single-cell LiPo packs, small boards |
| JST-SH / Qwiic / Stemma QT | 1.0 mm | 1 A | Plug-and-play I2C sensor chains |
| JST-GH | 1.25 mm | 1 A | Flight controllers, Pixhawk peripherals |
| Micro JST 1.25 / Molex PicoBlade | 1.25 mm | 1 A | Tiny drones, cameras, displays |
| XT30 | Bullet pair | 15 to 30 A | 3-inch drones, small robots |
| XT60 | Bullet pair | 30 to 60 A | 5-inch drones, robot batteries |
| XT90 | Bullet pair | 90 A | Large drones, e-bikes |
| Screw terminal block | 3.5 / 5.08 mm | 10 to 15 A | Power inputs, relay outputs, field wiring |
| DC barrel jack | 5.5 x 2.1 / 2.5 mm | 2 to 5 A | Wall adapters |
- Pin header / Dupont
- Pitch:
- 2.54 mm
- Current (approx.):
- 1 to 3 A
- Where you see it:
- Arduino shields, sensor modules, jumpers
- JST-XH
- Pitch:
- 2.5 mm
- Current (approx.):
- 3 A
- Where you see it:
- LiPo balance leads, 3D printer fans and endstops
- JST-PH
- Pitch:
- 2.0 mm
- Current (approx.):
- 2 A
- Where you see it:
- Single-cell LiPo packs, small boards
- JST-SH / Qwiic / Stemma QT
- Pitch:
- 1.0 mm
- Current (approx.):
- 1 A
- Where you see it:
- Plug-and-play I2C sensor chains
- JST-GH
- Pitch:
- 1.25 mm
- Current (approx.):
- 1 A
- Where you see it:
- Flight controllers, Pixhawk peripherals
- Micro JST 1.25 / Molex PicoBlade
- Pitch:
- 1.25 mm
- Current (approx.):
- 1 A
- Where you see it:
- Tiny drones, cameras, displays
- XT30
- Pitch:
- Bullet pair
- Current (approx.):
- 15 to 30 A
- Where you see it:
- 3-inch drones, small robots
- XT60
- Pitch:
- Bullet pair
- Current (approx.):
- 30 to 60 A
- Where you see it:
- 5-inch drones, robot batteries
- XT90
- Pitch:
- Bullet pair
- Current (approx.):
- 90 A
- Where you see it:
- Large drones, e-bikes
- Screw terminal block
- Pitch:
- 3.5 / 5.08 mm
- Current (approx.):
- 10 to 15 A
- Where you see it:
- Power inputs, relay outputs, field wiring
- DC barrel jack
- Pitch:
- 5.5 x 2.1 / 2.5 mm
- Current (approx.):
- 2 to 5 A
- Where you see it:
- Wall adapters
Choosing the right one
headers and Dupont jumpers for prototypes; JST-PH or JST-SH (Qwiic) for tidy, locking cables in finished builds.
XT30 or XT60 for main power, keyed so they cannot be plugged in backwards; JST-PH only for small single cells.
connectors with a latch or friction lock, crimped properly.
screw or lever terminals in a weatherproof box.
only use connectors rated for mains voltage and certified for the purpose.
Always use the same connector and polarity convention across your projects so batteries and chargers stay compatible.
Tips that prevent failures
- Measure pitch with a caliper before ordering; XH and PH look alike.
- Crimp with the right tool and die; see jumper wires and Dupont.
- Solder XT connectors with plenty of heat and slip heat shrink over each pin; see soldering.
- Put the female (socket) side on the power source so its live contacts are shrouded.
- Check the wire gauge matches the connector's current; see wire gauges.
Try it: Wire gauge calculator
Change the values and the diagram and results update as you type.
Common mistakes to avoid
- Ordering JST-PH when the board uses JST-XH.
- Using pin headers for motor or battery current.
- Putting exposed male pins on the battery side.
- Mixing polarity conventions between batteries and chargers.
- Over-tightening screw terminals on stranded wire without ferrules.
Frequently asked questions
How do I tell JST-XH from JST-PH?
Measure the pin spacing: XH is 2.5 mm and PH is 2.0 mm. XH housings are also larger.
How much current can an XT60 handle?
About 30 A continuous and up to 60 A in short bursts, depending on wire size and soldering quality.
What connector does Qwiic or Stemma QT use?
A 4-pin JST-SH connector with 1.0 mm pitch carrying 3.3 V, ground, SDA and SCL for I2C.
Can I use Dupont connectors for power?
Only for small currents, up to about 1 A. Use JST, XT or screw terminals for more.
Which side of a battery connector should be female?
The battery or power source side, so its live contacts are shrouded and harder to short.
Parts for this guide
Calculators
Terms in this guide
Projects that use it
Put this into practice: 1 step-by-step build in our project library uses parts from this guide.
Keep learning
Sources
- JST XH, PH, SH and GH series datasheets
- Amass XT30, XT60 and XT90 specifications
- SparkFun Qwiic and Adafruit Stemma QT documentation
Written by the Geekobot team from manufacturer datasheets. Always check the datasheet for the exact part and variant you buy.



