Build a belt-driven linear axis on 2020 extrusion with a CNC shield
A NEMA 17, a GT2 belt and an endstop make a homing axis: the same parts that move every 3D printer and plotter.
Shop by category
Shop all componentsMost print failures that start with clicking extruders, thin lines or molten plastic around the heater block come from the hotend. In this job you take a V6-style hotend apart, fit a new heat break, PTFE tube and push fitting, and change the nozzle with the hot-tightening method that stops leaks. The same steps work for most printers with M6 nozzles.
The hotend runs at 200 to 300 °C. Do hot work with tweezers and gloves, and switch the printer off before you touch wiring.
Tick anything you already have and the total updates.
Heat break: the thin tube that keeps the melt zone short
Heat sink that keeps the top of the heat break cold
Push fitting that holds the PTFE tube
Heat-sink fan: if it stops, the hotend clogs with heat creep
Fine bits to clear a nozzle from the tip
Spare Volcano nozzles if your printer uses the long Volcano block
The nozzle was not tight against the heat break. Repeat the hot-tighten step.
PTFE not seated against the nozzle leaves a gap where plastic pools. Cut it square and push it down again.
The thermistor slipped out of the block or a wire broke. Seat it again and check the wires before printing.
Brass wears quickly with glow-in-the-dark, wood and carbon-filled filaments. With plain PLA, change it when lines get wider or details soften.
0.4 mm is the default for most work. 0.2 mm gives fine detail, 0.6 to 0.8 mm prints fast and strong.
These are V6-style M6 parts. Bambu, Prusa and some Creality printers use their own hotends; check your model first.
9 parts: M6 Brass Nozzle 0.4mm for 1.75mm Filament (V5/V6/UM), V6 Heat Break Hotend Throat for 1.75mm Filament, V6 J-head Hotend Heatsink for 1.75mm Direct Drive, Two Trees PC4-M6 Pneumatic Bowden Extruder Connector, PTFE Bowden Tubing for 1.75mm Filament (1 Meter), Generic 12V 4010 Cooling Fan for 3D Printer Extruders, 3D Printer Nozzle Cleaning Drill Bit Kit (0.1-1.0mm) – 10 Pcs, Creality FDM Common Toolkit and V6 Volcano Brass Nozzle (More Sizes). On this page you can tick the parts you already have and add only the rest to your cart.
It is a intermediate project and takes about 2 hours. The build on this page has 7 steps.
No. It is a hardware circuit with no microcontroller and no code. Build it on a breadboard from the wiring table and steps on this page.
About ₹1,081 for the parts at the prices on this page. Quantity price breaks lower the cost when you build several.
What the heat sink, heat break, heater block and nozzle each do; Why a nozzle must be tightened hot; Cutting PTFE tube square and seating it against the nozzle; Cleaning a partial clog with a cold pull.
The hotend runs at 200 to 300 °C. Do hot work with tweezers and gloves, and switch the printer off before you touch wiring.
Ideas that reuse this build: Print strong outdoor parts in PETG, ASA, TPU and carbon fibre. They are listed under Take it further on this page.
A NEMA 17, a GT2 belt and an endstop make a homing axis: the same parts that move every 3D printer and plotter.
Stop re-levelling by hand: fit a CR Touch probe and a textured PEI spring-steel sheet for first layers that just stick.
Unbox, level, slice and print: a phone stand, a cable clip and a calibration cube, with the checks that save most beginners a week.
Choose the right engineering filament for outdoor parts: a UV-stable box, a soft seal and a stiff carbon-fibre bracket.
Learning project. Check every circuit and the datasheet of each part before you power it up.