Component guide · Beginner · 3 min read
433 MHz RF Remote Control Switches and Relay Modules

Pairing and Wiring
By Geekobot Learning Team · Updated 29 Oct 2026
On this page
433 MHz RF remote switches pair a key-fob remote with a receiver that switches lights, pumps, gates or motors without Wi-Fi or an app. The receivers come in 1, 2, 3 and 4 channel versions for mains or 12 V, and the motor version reverses a DC motor. Most use EV1527 learning code: press the learn button, then the remote key, and choose momentary, toggle or latched mode.
Key specs at a glance
- Frequency
- 433.92 MHz
- Code
- EV1527 learning code (1527 fixed code per remote)
- Channels
- 1, 2, 3 or 4
- Supply
- AC 220 V or DC 12 V by model
- Load
- About 10 A per relay (mains models), 60 W (12 V motor model)
- Range
- About 30 to 100 m open air, less through walls
- Modes
- Momentary, toggle, latched (interlock)
Models in this guide
These are alternatives. Pick the one that fits your project; you only need one.
Option 11-Channel RF Wireless Smart Switch w/ 433MHz Remote Control₹489
Option 22 Channel RF Wireless Smart Switch with 433MHz Remote Control₹503
Option 33 Channel RF Wireless Smart Switch w/ 433MHz Remote Control₹389
Option 412V One Channel RF Wireless Relay Module with Remote Control₹459
Option 5433MHz Wireless Motor Control Switch w/ Keychain Remote (12V DC, 60W)₹1,149
Option 64-Channel Wireless Relay Module (RF Remote)₹685
What the 433 MHz RF remote switch is
These are simple and reliable for places Wi-Fi does not reach: a borewell pump, gate motor, shop shutter light or vehicle accessory. The EV1527 learning receiver (GB-IOWC-9617) also suits Arduino projects: its outputs go HIGH for the pressed key.
A remote can be paired to several receivers, and one receiver learns many remotes.
433 MHz RF remote switch pinout
The pins on the 433 MHz RF remote switch and what each one does.
| Pin | Function |
|---|---|
| AC L / N or DC + / - | Supply |
| COM / NO / NC | Relay outputs |
| Motor + / - (motor version) | DC motor output, polarity reverses |
| Learn button | Pairing and mode selection |
| D0 to D3 (EV1527 receiver) | Logic outputs for each remote key |
- AC L / N or DC + / -
- Supply
- COM / NO / NC
- Relay outputs
- Motor + / - (motor version)
- DC motor output, polarity reverses
- Learn button
- Pairing and mode selection
- D0 to D3 (EV1527 receiver)
- Logic outputs for each remote key
Wiring the 433 MHz RF remote switch
Mains wiring must be done with the power off, in a proper enclosure, with cable and a fuse or MCB rated for the load. If you are not sure, have a qualified electrician install it. For the EV1527 receiver with an Arduino, power it from 5 V and read D0 to D3 as inputs.
| 433 MHz RF remote switch pin | Mains switch | 12 V motor module |
|---|---|---|
| Supply | AC 220 V to L / N | 12 V to + / - |
| Load | Light live through COM / NO | DC motor to motor terminals |
| Remote | Pair key A to channel 1 | Up and down keys |
- Supply
- Mains switch:
- AC 220 V to L / N
- 12 V motor module:
- 12 V to + / -
- Load
- Mains switch:
- Light live through COM / NO
- 12 V motor module:
- DC motor to motor terminals
- Remote
- Mains switch:
- Pair key A to channel 1
- 12 V motor module:
- Up and down keys
Example code
Set the receiver to momentary mode for this sketch. To send codes from an Arduino instead, use a 433 MHz transmitter with the RCSwitch library.
const int KEY[4] = {2, 3, 4, 5}; // D0..D3 outputs
void setup() {
Serial.begin(9600);
for (int k : KEY) pinMode(k, INPUT);
}
void loop() {
for (int i = 0; i < 4; i++)
if (digitalRead(KEY[i])) { Serial.print("Key "); Serial.println(i + 1); delay(300); }
}Setup and tuning
press the learn button once (or 1, 2, 3 times for different modes), then press the remote key within a few seconds.
hold the learn button about 8 s to erase all paired remotes.
keep the receiver's wire antenna straight; a 17 cm wire improves range.
remotes use 12 V A23 or CR2032 cells; weak cells shorten range.
What you need
Shop this list10 of 11 found in our store · ₹5,046
Generic 1-Channel RF Wireless Smart Switch w/ 433MHz Remote Control: the part this guide covers1-Channel RF Wireless Smart Switch w/ 433MHz Remote Control₹489
2 Channel RF Wireless Smart Switch with 433MHz Remote Control: another version this guide covers2 Channel RF Wireless Smart Switch with 433MHz Remote Control₹503
3 Channel RF Wireless Smart Switch w/ 433MHz Remote Control: another version this guide covers3 Channel RF Wireless Smart Switch w/ 433MHz Remote Control₹389
Generic 12V One Channel RF Wireless Relay Module with Remote Control: another version this guide covers12V One Channel RF Wireless Relay Module with Remote Control₹459
433MHz Wireless Motor Control Switch w/ Keychain Remote (12V DC, 60W): another version this guide covers433MHz Wireless Motor Control Switch w/ Keychain Remote (12V DC, 60W)₹1,149
4-Channel Wireless Relay Module (RF Remote): another version this guide covers4-Channel Wireless Relay Module (RF Remote)₹685
433MHz Learning Code Receiver and Remote (EV1527): another version this guide covers433MHz Learning Code Receiver and Remote (EV1527)₹106
433MHz 4-button remote: an extra remote to pairHelical Spring Coil Antenna₹40
Sonoff RM433R2 8-key RF remote: a multi-key remoteSonoff RM433R2 8-Key RF Remote Control₹1,049- Fuse holder: to fuse the switched circuitFind this part
Digital multimeter: to check supply and signal voltagesDigital Multimeter₹177
Alternatives and when to choose them
- 433 MHz RF modules: transmitter and receiver modules for Arduino.
- Sonoff BASIC and MINI: Wi-Fi switches, some with RF.
- Relay modules: relay boards for microcontrollers.
Common mistakes to avoid
- Expecting long range through concrete walls.
- Forgetting which mode was set while pairing.
- Using a motor module above its 60 W rating.
- Coiling the antenna wire.
Frequently asked questions
What is learning code?
The receiver learns each remote's unique code, so any EV1527 remote can be paired.
Can I use one remote for several receivers?
Yes, pair the same key or different keys to each.
What is the range?
About 30 to 100 m in open air, less indoors.
Can Home Assistant control them?
Yes, through a 433 MHz bridge such as the Sonoff RF Bridge.
Can it reverse a motor?
Yes, the 12 V motor model switches polarity.
Parts for this guide
Keep learning
Sources
Written by the Geekobot team from manufacturer datasheets. Always check the datasheet for the exact part and variant you buy.


