How-to · Beginner · 3 min read
433 MHz RF Transmitter and Receiver Modules
Wiring, Range and Code
By Geekobot Learning Team · Updated 24 Oct 2026
On this page
The 433 MHz transmitter and receiver pair (FS1000A and XY-MK-5V) is the cheapest way to send simple data one way between two boards. The transmitter switches a 433 MHz carrier on and off with your data; the receiver turns it back into pulses. Add a 17.3 cm wire antenna to both, use the RadioHead library for messages or rc-switch for remote-control codes, and expect 20 to 100 m depending on antennas and supply voltage.
Key specs at a glance
- Transmitter
- FS1000A, 3 to 12 V, ASK/OOK modulation
- Receiver
- XY-MK-5V (super-regenerative), 5 V; RXB6 is a better superheterodyne receiver
- Data rate
- Practical 1 to 4 kbps (2000 bps typical)
- Antenna
- 17.3 cm straight wire (quarter wave)
- Range
- 20 to 100 m typical; more at 9 to 12 V on the transmitter
- Link
- One way, no acknowledgement
Wiring the pair
| Module | Pin | Arduino | Notes |
|---|---|---|---|
| Transmitter FS1000A | VCC | 5V (or up to 12 V for more range) | |
| Transmitter FS1000A | DATA | D12 | RadioHead default TX pin |
| Transmitter FS1000A | GND | GND | |
| Receiver XY-MK-5V | VCC | 5V | Needs 5 V |
| Receiver XY-MK-5V | DATA (either middle pin) | D11 | RadioHead default RX pin |
| Receiver XY-MK-5V | GND | GND | |
| Both | ANT | 17.3 cm solid wire | Solder to the ANT pad |
- Transmitter FS1000A
- Pin:
- VCC
- Arduino:
- 5V (or up to 12 V for more range)
- Transmitter FS1000A
- Pin:
- DATA
- Arduino:
- D12
- Notes:
- RadioHead default TX pin
- Transmitter FS1000A
- Pin:
- GND
- Arduino:
- GND
- Receiver XY-MK-5V
- Pin:
- VCC
- Arduino:
- 5V
- Notes:
- Needs 5 V
- Receiver XY-MK-5V
- Pin:
- DATA (either middle pin)
- Arduino:
- D11
- Notes:
- RadioHead default RX pin
- Receiver XY-MK-5V
- Pin:
- GND
- Arduino:
- GND
- Both
- Pin:
- ANT
- Arduino:
- 17.3 cm solid wire
- Notes:
- Solder to the ANT pad
Send text with RadioHead
Install RadioHead (it includes RH_ASK). Upload the sender to one board and the receiver to the other.
#include <RH_ASK.h>
#include <SPI.h> // required by RadioHead even though ASK does not use SPI
RH_ASK rf(2000, 11, 12); // speed (bps), RX pin, TX pin
const bool SENDER = true;
void setup() {
Serial.begin(115200);
if (!rf.init()) Serial.println("RF init failed");
}
void loop() {
if (SENDER) {
const char *msg = "door=open";
rf.send((uint8_t *)msg, strlen(msg));
rf.waitPacketSent();
delay(1000);
} else {
uint8_t buf[RH_ASK_MAX_MESSAGE_LEN];
uint8_t len = sizeof(buf);
if (rf.recv(buf, &len)) {
Serial.write(buf, len);
Serial.println();
}
}
}Remote sockets, doorbells and rc-switch
Many cheap remote-controlled sockets, doorbells and gate remotes use 433 MHz with fixed codes. The rc-switch library can receive those codes from your own remote and send them, so an Arduino or ESP32 can switch your sockets. This works only for fixed-code devices; car keys and modern gate remotes use rolling codes and will not respond to a replay. Only control devices you own.
The HT12E encoder and HT12D decoder ICs do the same without a microcontroller: set an address with DIP switches, press a button on the transmitter side, and the matching output goes HIGH on the receiver side. They are a classic choice for simple remote-control projects.
Improving range and reliability
- Fit antennas. Without them, range drops to a few metres. A 17.3 cm straight wire is a quarter wavelength at 433.92 MHz; a coil-loaded spring antenna also works.
- Raise the transmitter supply to 9 to 12 V (the FS1000A accepts it); the receiver stays at 5 V.
- Replace the receiver with an RXB6 or another superheterodyne module; the basic XY-MK-5V is noisy and easily swamped.
- Send each message several times and add a checksum (RadioHead does this) since there is no acknowledgement.
- For two-way links with addressing, use an nRF24L01, a LoRa module or an HC-12 serial transceiver.
Try it: Frequency wavelength calculator
Change the values and the diagram and results update as you type.
Common mistakes to avoid
- Running without antennas.
- Powering the receiver from 3.3 V.
- Expecting two-way communication or delivery confirmation.
- Leaving out SPI.h with RadioHead and getting compile errors.
- Using it for security-critical locks; fixed codes can be recorded and replayed.
Frequently asked questions
What is the range of the 433 MHz RF module?
About 20 to 100 m with 17.3 cm antennas, depending on obstacles, receiver quality and transmitter voltage. Without antennas it is only a few metres.
How long should a 433 MHz antenna be?
About 17.3 cm for a straight quarter-wave wire. Solder it to the ANT pad on both modules.
Can the 433 MHz module work with ESP32?
Yes. The transmitter works from 3.3 V signals. Power the receiver from 5 V and use a divider on its data output, or choose a 3.3 V receiver module.
Can I copy my remote control with a 433 MHz receiver?
For simple fixed-code remotes you own, such as plug sockets, yes with rc-switch. Rolling-code remotes cannot be copied this way.
Is 433 MHz legal in India?
Low-power devices in the 433 MHz band are license-exempt in India. Keep transmit power low and check the current WPC rules for commercial products.
Parts for this guide
Calculators
Terms in this guide
Keep learning
Sources
- RadioHead library documentation (RH_ASK)
- Holtek HT12E and HT12D datasheets
- Typical FS1000A and XY-MK-5V module specifications
Written by the Geekobot team from manufacturer datasheets. Always check the datasheet for the exact part and variant you buy.


