Comparison · Beginner · 4 min read
Wi-Fi vs Bluetooth vs LoRa vs Zigbee
Choosing a Wireless Module
By Geekobot Learning Team · Updated 24 Oct 2026
On this page
Pick by range, data and power. Use Wi-Fi (ESP32) when the device is near a router and needs the internet or lots of data. Use Bluetooth Low Energy to talk to a phone. Use ESP-NOW or an nRF24L01 for direct board-to-board links within a building. Use LoRa for small messages over kilometres on batteries. Use Zigbee or Thread for low-power smart-home meshes, and 4G when there is no Wi-Fi at all.
Key specs at a glance
- Highest data
- Wi-Fi
- Phone connection
- BLE (or Bluetooth Classic serial)
- Longest range on batteries
- LoRa
- Cheapest one-way link
- 433 MHz ASK
- Mesh smart home
- Zigbee, Thread
- Anywhere with coverage
- 4G LTE (SIM required)
The options compared
| Technology | Typical range | Data rate | Power | Typical hardware |
|---|---|---|---|---|
| Wi-Fi | 30 to 50 m indoors | Mbps | High (80 to 250 mA when active) | ESP32, ESP8266, Pico W |
| Bluetooth Low Energy | 10 to 30 m | Up to about 1 to 2 Mbps | Very low | ESP32, ESP32-C3, nRF52 |
| Bluetooth Classic (SPP) | 10 m | Up to about 2 Mbps (serial links much less) | Medium | HC-05, classic ESP32 |
| ESP-NOW | 100 to 200 m line of sight | Small packets (250 bytes, v2 more) | Low to medium | Any two ESP32 or ESP8266 boards |
| nRF24L01 | 20 to 100 m (1 km with PA+LNA) | 250 kbps to 2 Mbps | Low | nRF24L01 modules |
| 433 MHz ASK | 20 to 100 m | 1 to 4 kbps, one way | Very low | FS1000A + receiver |
| LoRa | 2 to 10+ km | 0.3 to 5 kbps | Very low | SX1276/SX1278, Ra-02 |
| Zigbee / Thread | 10 to 30 m per hop, mesh | 250 kbps | Very low | XBee, ESP32-C6, ESP32-H2 |
| 4G LTE / 2G GSM | Wherever there is coverage | Kbps to Mbps | High | A7670, SIM7600, SIM800L |
- Wi-Fi
- Typical range:
- 30 to 50 m indoors
- Data rate:
- Mbps
- Power:
- High (80 to 250 mA when active)
- Typical hardware:
- ESP32, ESP8266, Pico W
- Bluetooth Low Energy
- Typical range:
- 10 to 30 m
- Data rate:
- Up to about 1 to 2 Mbps
- Power:
- Very low
- Typical hardware:
- ESP32, ESP32-C3, nRF52
- Bluetooth Classic (SPP)
- Typical range:
- 10 m
- Data rate:
- Up to about 2 Mbps (serial links much less)
- Power:
- Medium
- Typical hardware:
- HC-05, classic ESP32
- ESP-NOW
- Typical range:
- 100 to 200 m line of sight
- Data rate:
- Small packets (250 bytes, v2 more)
- Power:
- Low to medium
- Typical hardware:
- Any two ESP32 or ESP8266 boards
- nRF24L01
- Typical range:
- 20 to 100 m (1 km with PA+LNA)
- Data rate:
- 250 kbps to 2 Mbps
- Power:
- Low
- Typical hardware:
- nRF24L01 modules
- 433 MHz ASK
- Typical range:
- 20 to 100 m
- Data rate:
- 1 to 4 kbps, one way
- Power:
- Very low
- Typical hardware:
- FS1000A + receiver
- LoRa
- Typical range:
- 2 to 10+ km
- Data rate:
- 0.3 to 5 kbps
- Power:
- Very low
- Typical hardware:
- SX1276/SX1278, Ra-02
- Zigbee / Thread
- Typical range:
- 10 to 30 m per hop, mesh
- Data rate:
- 250 kbps
- Power:
- Very low
- Typical hardware:
- XBee, ESP32-C6, ESP32-H2
- 4G LTE / 2G GSM
- Typical range:
- Wherever there is coverage
- Data rate:
- Kbps to Mbps
- Power:
- High
- Typical hardware:
- A7670, SIM7600, SIM800L
Which one for your project?
Wi-Fi on an ESP32, MQTT to Home Assistant. See MQTT and Home Assistant.
BLE on an ESP32, or an HC-05 with an Arduino for a simple serial link.
nRF24L01 or ESP-NOW for low latency.
LoRa on battery and solar.
4G module with SMS. See SIM800L and 4G modules.
Zigbee or Thread on an ESP32-C6 or ESP32-H2.
433 MHz with an HT12E/HT12D pair.
Power is usually the deciding factor
Wi-Fi radios draw hundreds of milliamps while connected, so a Wi-Fi sensor on batteries must sleep most of the time and wake to send (see deep sleep and battery power). BLE, LoRa, Zigbee and nRF24L01 radios can run for months or years on small batteries because they transmit briefly and sleep in microamps. 4G modules need large current bursts and a solid supply. If the device is mains powered, the choice is mostly about range and data.
ESP-NOW: the easy board-to-board option
ESP-NOW is Espressif's peer-to-peer protocol. Any two ESP32 or ESP8266 boards can exchange small packets directly by MAC address, without a router, with low latency and decent range. It is ideal for remote sensors reporting to one ESP32 hub, which then bridges to Wi-Fi and MQTT. No extra module is needed, which makes it the first thing to try before buying radios.
Try it: Battery life calculator
Change the values and the diagram and results update as you type.
Common mistakes to avoid
- Choosing Wi-Fi for a battery sensor that must last a year without deep sleep.
- Expecting LoRa to carry images or audio.
- Using Bluetooth Classic modules to talk to an iPhone (iOS does not support SPP for general apps).
- Ignoring antenna placement inside metal enclosures.
- Forgetting that 4G modules need a SIM plan and 2 A supply peaks.
Frequently asked questions
Which is better for IoT, Wi-Fi or LoRa?
Wi-Fi when a router is nearby and you need data or internet access. LoRa when devices are far away, send small messages and run on batteries.
What is the longest-range wireless module for Arduino?
LoRa, which typically reaches several kilometres. 4G modules work anywhere with mobile coverage but need a SIM plan.
Is Zigbee better than Wi-Fi for smart home?
For battery sensors and large meshes, yes: Zigbee uses far less power and every mains device extends the mesh. Wi-Fi is simpler for a few mains-powered devices.
What is ESP-NOW?
A direct, router-free protocol between ESP32 and ESP8266 boards for small, fast messages, built into their Wi-Fi radios.
Can Bluetooth reach 100 metres?
Typical modules reach 10 to 30 m. BLE long-range (coded PHY) on some chips can go further, but LoRa or nRF24L01 with PA+LNA are better for 100 m and beyond.
Parts for this guide
Calculators
Terms in this guide
Projects that use it
Put this into practice: 57 step-by-step builds in our project library use parts from this guide.
Keep learning
Sources
- Espressif ESP32 and ESP-NOW documentation
- Bluetooth SIG core specification overview
- Semtech LoRa modulation basics
- Connectivity Standards Alliance Zigbee overview
Written by the Geekobot team from manufacturer datasheets. Always check the datasheet for the exact part and variant you buy.


