GPS speedometer and clock
A bike or car speedometer that needs no wheel sensor: satellites do the measuring.
Shop by category
Shop all componentsWi-Fi does not reach the far fields and SMS costs money for every reading. LoRa radio sends small messages a long way for very little power. This node reads the soil probe and a soil thermometer and broadcasts them every 30 seconds, with ALERT added when the soil is dry. Pair it with either receiver.
Tick anything you already have and the total updates.
Long-range 433 MHz radio that sends small messages a kilometre or more across open fields with very little power.
Capacitive probe that measures soil moisture without exposed metal, so it does not corrode like resistive probes.
Waterproof stainless-steel probe that reads liquid or soil temperature from −55 to +125 °C (±0.5 °C).
Charges the cell, from a small solar panel if you like
Follow the colours: red is power, dark grey is ground, blue is a signal.
Cell to the TP4056 B+ and B−; TP4056 OUT+ to the ESP32-C3 5V pin and OUT− to GND. The board's own regulator makes 3.3 V from the cell, and the LoRa module takes its 3.3 V from the board. Put the node in a sealed box with the antenna outside and upright.
lora_field_soil_node.inoVerify & upload in Electrolark// LoRa field soil moisture node
// Geekobot project library · board: ESP32-C3 SuperMini
// Wiring diagram, parts list and build steps: Geekobot project page "lora-field-soil-node"
#include <SPI.h>
#include <LoRa.h>
#include <OneWire.h>
#include <DallasTemperature.h>
// ---- pins ----
const uint8_t LORA_RST = 10;
const uint8_t LORA_DIO0 = 3;
const uint8_t SOIL_PIN = 0;
const uint8_t ONEWIRE_PIN = 2;
const int SOIL_DRY = 2600; // reading in dry air: calibrate
const int SOIL_WET = 1150; // reading in a glass of water: calibrate
OneWire oneWire(ONEWIRE_PIN);
DallasTemperature probes(&oneWire);
// ---- latest readings ----
int soilPct = 0;
float probeC = 0;
const char NODE[] = "FIELD1"; // the receiver shows this name
const unsigned long SEND_EVERY_MS = 30000UL;
unsigned long lastSend = 0;
bool wasAlarm = false;
float readProbeC() {
probes.requestTemperatures();
return probes.getTempCByIndex(0);
}
void setup() {
Serial.begin(115200);
LoRa.setPins(SS, LORA_RST, LORA_DIO0);
if (!LoRa.begin(433E6)) Serial.println(F("LoRa module not found"));
LoRa.setSpreadingFactor(10); // slower but reaches further
probes.begin();
}
void loop() {
soilPct = constrain(map(analogRead(SOIL_PIN), SOIL_DRY, SOIL_WET, 0, 100), 0, 100);
probeC = readProbeC();
String msg = String(NODE) + ";" + String("soilPct=") + String(soilPct) + ";" + String("probeC=") + String(probeC);
bool alarm = soilPct < 30;
if (alarm) msg += ";ALERT";
bool urgent = alarm && !wasAlarm;
wasAlarm = alarm;
if (urgent || millis() - lastSend >= SEND_EVERY_MS || lastSend == 0) {
LoRa.beginPacket(); LoRa.print(msg); LoRa.endPacket();
lastSend = millis();
Serial.print(F("Sent: ")); Serial.println(msg);
}
delay(200);
}
The sketch above runs here on a simulated ESP32-C3. Move the sliders for the sensors and buttons it reads, and watch the Serial monitor, display and outputs change.
Check the four SPI wires and that NSS and RST go to the pins in the sketch.
Mount both antennas high and vertical, clear of metal. Range drops sharply behind buildings.
Calibrate: note the raw reading in dry air and in water, and put them in SOIL_DRY and SOIL_WET.
The 4.7 kΩ pull-up is missing or DATA is on the wrong pin. Check the yellow wire.
Open the Serial Monitor at 115200 baud and check for messages. Make sure you chose the right board and port in the Arduino IDE.
Close other programs using the serial port, try another USB cable (some are charge-only) and press reset just before uploading.
Use a 5 V USB phone charger or a power bank into the board's USB port.
10 parts: ESP32-C3 SuperMini Development Board, SX1278 LoRa Module RA-02 433MHz, Capacitive Soil Moisture Sensor – 3.3V/5V Analog Output, DS18B20 Waterproof Temperature Probe – 1m Cable, Resistor Assortment Kit (30 Values), 18650 Battery Holder, 18650 Li-ion Rechargeable Cell 2600mAh, TP4056 1A Li-ion Charger Module with Protection, Solderless Breadboard (830 points) and Dupont Jumper Wires (40 pcs). Tools: Digital Multimeter and Wire Stripper and Cutter. On this page you can tick the parts you already have and add only the rest to your cart.
It is a intermediate project and takes about 2 hours. The build on this page has 8 steps.
No. This page has the complete, tested code (lora_field_soil_node.ino). Install these libraries first: LoRa, OneWire and DallasTemperature.
Yes. The Run it panel under the code runs this exact sketch on a simulated board. Move the sliders or press the buttons for the sensors it reads, and the Serial monitor, display and outputs react as they will on the real build. It is a simulation, so real readings depend on your parts and wiring.
About ₹1,039 for the parts at the prices on this page, plus tools if you do not have them. Quantity price breaks lower the cost when you build several.
1-Wire bus and pull-up resistors; Calibrating an analog sensor with map(); LoRa radio and spreading factor.
Ideas that reuse this build: Receiver with an OLED and Receiver with an alarm. They are listed under Take it further on this page.
A bike or car speedometer that needs no wheel sensor: satellites do the measuring.
Records where you went every five seconds, ready to open on a map.
Two boards, two radios: press the button at the gate and it rings indoors.
Check temperature, humidity and pressure from any phone on your Wi-Fi.
Learning project. Check every circuit and the datasheet of each part before you power it up.
Sent: FIELD1;soilPct=94;probeC=26.00
A simulation of the sketch above, so you know what to expect. Real readings vary with your parts and wiring.