GPS speedometer and clock
A bike or car speedometer that needs no wheel sensor: satellites do the measuring.
Shop by category
Shop all componentsEach fix is written to TRACK.CSV with time, latitude, longitude, speed and altitude. Import the file into Google My Maps or any GPX converter to see the route of a cycle ride, school trip or delivery run.
Tick anything you already have and the total updates.
Connects the Uno to your computer to upload code and power it
GPS receiver that outputs position, speed, altitude and UTC time once it sees at least 4 satellites.
Stores readings on a microSD card as a CSV file you can open in Excel or Google Sheets.
Follow the colours: red is power, dark grey is ground, blue is a signal.
gps_route_logger.inoVerify & upload in Electrolark// GPS route logger
// Geekobot project library · board: Arduino Uno
// Wiring diagram, parts list and build steps: Geekobot project page "gps-route-logger"
#include <TinyGPSPlus.h>
#include <SPI.h>
#include <SD.h>
#include <SoftwareSerial.h>
// ---- pins ----
const uint8_t GPS_RX = 2;
const uint8_t GPS_TX = 3;
const uint8_t SD_CS = 10;
TinyGPSPlus gps;
SoftwareSerial gpsSerial(GPS_RX, GPS_TX);
const unsigned long LOG_EVERY_MS = 5000; // one point every 5 s
unsigned long lastLog = 0;
bool cardOk = false;
void setup() {
Serial.begin(115200);
gpsSerial.begin(9600);
cardOk = SD.begin(SD_CS);
Serial.println(cardOk ? F("SD ready") : F("SD card not found"));
if (cardOk && !SD.exists("TRACK.CSV")) { File f = SD.open("TRACK.CSV", FILE_WRITE); if (f) { f.println(F("utc,lat,lon,speed_kmh,alt_m,sats")); f.close(); } }
}
void loop() {
while (gpsSerial.available()) gps.encode(gpsSerial.read());
if (millis() - lastLog < LOG_EVERY_MS) return;
lastLog = millis();
if (!gps.location.isValid()) { Serial.println(F("No fix yet")); return; }
char stamp[24];
snprintf(stamp, sizeof(stamp), "%04d-%02d-%02dT%02d:%02d:%02d", gps.date.year(), gps.date.month(), gps.date.day(), gps.time.hour(), gps.time.minute(), gps.time.second());
File f = SD.open("TRACK.CSV", FILE_WRITE);
if (!f) return;
f.print(stamp); f.print(',');
f.print(gps.location.lat(), 6); f.print(',');
f.print(gps.location.lng(), 6); f.print(',');
f.print(gps.speed.kmph(), 1); f.print(',');
f.print(gps.altitude.meters(), 1); f.print(',');
f.println(gps.satellites.value());
f.close();
Serial.println(stamp);
}
The sketch above runs here on a simulated Arduino Uno. Move the sliders for the sensors and buttons it reads, and watch the Serial monitor, display and outputs change.
GPS needs open sky. Test near a window or outside; the first cold start can take several minutes.
Check the card is FAT32, fully inserted, and CS is on the pin in the sketch.
Open the Serial Monitor at 115200 baud and check for messages. Make sure you chose the right board and port in the Arduino IDE.
Close other programs using the serial port, try another USB cable (some are charge-only) and press reset just before uploading.
Yes. Most of the code works unchanged on an ESP32 with the ESP32 board package. Watch for 5 V modules: ESP32 pins are 3.3 V, so 5 V output signals need a resistor divider.
Use a 5 V USB phone charger or a power bank into the board's USB port.
10 parts: Uno R3 CH340G ATmega328p Compatible Development Board, Arduino USB-A to USB-B Data Cable for UNO/MEGA, GY-NEO6MV2 GPS Module with u-blox NEO-6M & Antenna, DFRobot Fermion MicroSD Card Module – SPI, microSD Memory Card Class 10 (16GB), 18650 Battery Holder, 18650 Li-ion Rechargeable Cell 2600mAh, MT3608 Mini Boost Converter Module, Solderless Breadboard (830 points) and Dupont Jumper Wires (40 pcs). Tools: Digital Multimeter and Wire Stripper and Cutter. On this page you can tick the parts you already have and add only the rest to your cart.
It is a intermediate project and takes about 2–3 hours. The build on this page has 7 steps.
No. This page has the complete, tested code (gps_route_logger.ino). Install these libraries first: TinyGPSPlus and SD.
Yes. The Run it panel under the code runs this exact sketch on a simulated board. Move the sliders or press the buttons for the sensors it reads, and the Serial monitor, display and outputs react as they will on the real build. It is a simulation, so real readings depend on your parts and wiring.
About ₹1,795 for the parts at the prices on this page, plus tools if you do not have them. Quantity price breaks lower the cost when you build several.
NMEA sentences and GNSS fixes; SPI devices and CSV logging.
Ideas that reuse this build: Live speedometer. They are listed under Take it further on this page.
A bike or car speedometer that needs no wheel sensor: satellites do the measuring.
Two boards, two radios: press the button at the gate and it rings indoors.
Check temperature, humidity and pressure from any phone on your Wi-Fi.
Soil moisture and room climate on your phone, with automatic watering and a manual override.
Learning project. Check every circuit and the datasheet of each part before you power it up.
SD ready
A simulation of the sketch above, so you know what to expect. Real readings vary with your parts and wiring.