GPS speedometer and clock
A bike or car speedometer that needs no wheel sensor: satellites do the measuring.
Shop by category
Shop all componentsThe ESP32-C3 reads the DHT22 and BMP280 and serves a live dashboard page. Open its address in a browser on any phone or laptop on the same network; the cards refresh every two seconds.
Tick anything you already have and the total updates.
Measures air temperature (±0.5 °C) and relative humidity (±2–5 %) on a single data wire.
Measures barometric pressure (±1 hPa) and temperature over I²C.
Follow the colours: red is power, dark grey is ground, blue is a signal.
wifi_weather_station.inoVerify & upload in Electrolark// Wi-Fi weather station dashboard
// Geekobot project library · board: ESP32-C3 SuperMini
// Wiring diagram, parts list and build steps: Geekobot project page "wifi-weather-station"
#include <DHT.h>
#include <Wire.h>
#include <Adafruit_BMP280.h>
#include <WiFi.h>
#include <WebServer.h>
// ---- pins ----
const uint8_t DHT_PIN = 10;
DHT dht(DHT_PIN, DHT22);
Adafruit_BMP280 bmp;
// ---- latest readings ----
float tempC = 0;
float humidity = 0;
float pressHpa = 0;
float bmpC = 0;
const char* WIFI_SSID = "YOUR_WIFI_NAME"; // 2.4 GHz network
const char* WIFI_PASS = "YOUR_WIFI_PASSWORD";
WebServer server(80);
const unsigned long READ_EVERY_MS = 2000;
unsigned long lastRead = 0;
const char* statusText = "Starting";
const char PAGE[] PROGMEM = R"HTML(<!doctype html><html><head><meta name="viewport" content="width=device-width,initial-scale=1"><title>Weather station</title>
<style>body{font-family:system-ui,sans-serif;background:#0d093d;color:#fff;margin:0;padding:20px}h1{font-size:20px;margin:0 0 14px}
.g{display:grid;grid-template-columns:repeat(auto-fit,minmax(140px,1fr));gap:12px}.c{background:#1c1866;border-radius:14px;padding:14px}
.l{font-size:12px;opacity:.7}.v{font-size:28px;font-weight:700;margin-top:4px}button{margin-top:14px;padding:12px 18px;border:0;border-radius:10px;font-size:16px;background:#a9c5ea;color:#0d093d}
.s{margin-top:12px;font-size:13px;opacity:.8}</style></head><body><h1>Weather station</h1><div class="g" id="g"></div><p class="s" id="s">Connecting…</p>
<script>const F=[["tempC","Temp","C"],["humidity","Humidity","%"],["pressHpa","Pressure","hPa"],["bmpC","Temp","C"]];
async function tick(){try{const d=await(await fetch('/data')).json();document.getElementById('g').innerHTML=F.map(f=>'<div class="c"><div class="l">'+f[1]+'</div><div class="v">'+(typeof d[f[0]]==='boolean'?(d[f[0]]?'YES':'no'):d[f[0]])+' '+f[2]+'</div></div>').join('');
document.getElementById('s').textContent='Status: '+d.status+' · updated '+new Date().toLocaleTimeString();}catch(e){document.getElementById('s').textContent='Lost connection, retrying…'}}
setInterval(tick,2000);tick();</script></body></html>)HTML";
void handleData() {
String j = "{";
j += "\"tempC\":"; j += String(tempC, 1); j += ",";
j += "\"humidity\":"; j += String(humidity, 0); j += ",";
j += "\"pressHpa\":"; j += String(pressHpa, 1); j += ",";
j += "\"bmpC\":"; j += String(bmpC, 1); j += ",";
j += "\"status\":\""; j += statusText; j += "\"}";
server.send(200, "application/json", j);
}
void handleRoot() { server.send(200, "text/html", PAGE); }
void evaluate() {
if (!(!isnan(tempC) && !isnan(humidity))) { statusText = "Sensor error"; return; }
statusText = "OK";
}
void setup() {
Serial.begin(115200);
dht.begin();
if (!bmp.begin(0x76) && !bmp.begin(0x77)) Serial.println(F("BMP280 not found"));
WiFi.mode(WIFI_STA);
WiFi.begin(WIFI_SSID, WIFI_PASS);
Serial.print(F("Connecting to Wi-Fi"));
for (int i = 0; i < 40 && WiFi.status() != WL_CONNECTED; i++) { delay(500); Serial.print("."); }
Serial.println();
Serial.print(F("Open this address in your browser: http://"));
Serial.println(WiFi.localIP());
server.on("/", handleRoot);
server.on("/data", handleData);
server.begin();
}
void loop() {
server.handleClient();
if (millis() - lastRead >= READ_EVERY_MS) {
lastRead = millis();
tempC = dht.readTemperature();
humidity = dht.readHumidity();
pressHpa = bmp.readPressure() / 100.0f;
bmpC = bmp.readTemperature();
evaluate();
Serial.print(F("Temp="));
Serial.print(tempC, 1);
Serial.print(F("C"));
Serial.print(F(", Humidity="));
Serial.print(humidity, 0);
Serial.print(F("%"));
Serial.print(F(", Pressure="));
Serial.print(pressHpa, 1);
Serial.print(F("hPa"));
Serial.print(F(", Temp="));
Serial.print(bmpC, 1);
Serial.print(F("C"));
Serial.println();
}
}
The sketch above runs here on a simulated ESP32-C3. Move the sliders for the sensors and buttons it reads, and watch the Serial monitor, display and outputs change.
Check the DATA wire and the pull-up. The DHT22 needs at least 2 seconds between reads, so do not poll it faster.
Check SDA/SCL are not swapped. Run an I²C scanner sketch to confirm the address.
Open the Serial Monitor at 115200 baud and check for messages. Make sure you chose the right board and port in the Arduino IDE.
Close other programs using the serial port, try another USB cable (some are charge-only) and press reset just before uploading.
Not directly; the board serves the page on your local network only. For remote access, send the readings to a cloud service such as MQTT, ThingSpeak or Blynk, or use a VPN into your home network.
No. ESP32-C3 and ESP8266 boards support 2.4 GHz networks only. Most routers broadcast both, so choose the 2.4 GHz name.
5 parts: ESP32-C3 SuperMini Development Board, DHT22 Temperature & Humidity Sensor, BMP280 Temperature & Barometric Pressure Sensor Module, Solderless Breadboard (830 points) and Dupont Jumper Wires (40 pcs). Tools: Digital Multimeter and Wire Stripper and Cutter. On this page you can tick the parts you already have and add only the rest to your cart.
It is a beginner project and takes about 1–2 hours. The build on this page has 7 steps.
No. This page has the complete, tested code (wifi_weather_station.ino). Install these libraries first: DHT sensor library, Adafruit Unified Sensor and Adafruit BMP280 Library.
Yes. The Run it panel under the code runs this exact sketch on a simulated board. Move the sliders or press the buttons for the sensors it reads, and the Serial monitor, display and outputs react as they will on the real build. It is a simulation, so real readings depend on your parts and wiring.
About ₹552 for the parts at the prices on this page, plus tools if you do not have them. Quantity price breaks lower the cost when you build several.
Single-wire digital sensors and why some sensors need slow polling; The I²C bus and device addresses.
Ideas that reuse this build: OLED version and SD logger. They are listed under Take it further on this page.
A bike or car speedometer that needs no wheel sensor: satellites do the measuring.
Records where you went every five seconds, ready to open on a map.
Two boards, two radios: press the button at the gate and it rings indoors.
Soil moisture and room climate on your phone, with automatic watering and a manual override.
Learning project. Check every circuit and the datasheet of each part before you power it up.
Connecting to Wi-Fi... Open this address in your browser: http://192.168.1.50 Temp=26.9C, Humidity=55%, Pressure=1008.0hPa, Temp=26.0C
A simulation of the sketch above, so you know what to expect. Real readings vary with your parts and wiring.