LPG gas leak alarm
A kitchen gas sniffer that beeps and flashes the moment LPG levels climb.
Shop by category
Shop all componentsA data logger for school science and home weather records. Every minute a row is added to LOG.CSV with the date, time and all readings, ready for charts.
Tick anything you already have and the total updates.
Connects the Uno to your computer to upload code and power it
Measures air temperature (±0.5 °C) and relative humidity (±2–5 %) on a single data wire.
Measures barometric pressure (±1 hPa) and temperature over I²C.
Temperature-compensated real-time clock (±2 minutes a year) with a coin-cell backup, so the time survives power cuts.
Stores readings on a microSD card as a CSV file you can open in Excel or Google Sheets.
Follow the colours: red is power, dark grey is ground, blue is a signal.
weather_data_logger.inoVerify & upload in Electrolark// Weather data logger
// Geekobot project library · board: Arduino Uno
// Wiring diagram, parts list and build steps: Geekobot project page "weather-data-logger"
#include <DHT.h>
#include <Wire.h>
#include <Adafruit_BMP280.h>
#include <RTClib.h>
#include <SPI.h>
#include <SD.h>
// ---- pins ----
const uint8_t DHT_PIN = 2;
const uint8_t SD_CS = 10;
DHT dht(DHT_PIN, DHT22);
Adafruit_BMP280 bmp;
RTC_DS3231 rtc;
// ---- latest readings ----
float tempC = 0;
float humidity = 0;
float pressHpa = 0;
float bmpC = 0;
const unsigned long LOG_EVERY_MS = 60000UL; // one row per minute
unsigned long lastLog = 0;
bool cardOk = false;
void writeRow() {
File f = SD.open("LOG.CSV", FILE_WRITE);
if (!f) { Serial.println(F("Write failed")); return; }
DateTime t = rtc.now();
char stamp[20];
snprintf(stamp, sizeof(stamp), "%04d-%02d-%02d,%02d:%02d:%02d", t.year(), t.month(), t.day(), t.hour(), t.minute(), t.second());
f.print(stamp);
f.print(',');
f.print(tempC, 1);
f.print(',');
f.print(humidity, 0);
f.print(',');
f.print(pressHpa, 1);
f.print(',');
f.print(bmpC, 1);
f.println();
f.close();
}
void setup() {
Serial.begin(115200);
dht.begin();
if (!bmp.begin(0x76) && !bmp.begin(0x77)) Serial.println(F("BMP280 not found"));
if (!rtc.begin()) Serial.println(F("RTC not found"));
if (rtc.lostPower()) rtc.adjust(DateTime(F(__DATE__), F(__TIME__))); // set from the upload time
cardOk = SD.begin(SD_CS);
Serial.println(cardOk ? F("SD card ready") : F("SD card not found"));
if (cardOk && !SD.exists("LOG.CSV")) {
File f = SD.open("LOG.CSV", FILE_WRITE);
if (f) { f.println(F("date,time,Temp(C),Humidity(%),Pressure(hPa),Temp(C)")); f.close(); }
}
}
void loop() {
if (millis() - lastLog < LOG_EVERY_MS && lastLog != 0) return;
lastLog = millis();
tempC = dht.readTemperature();
humidity = dht.readHumidity();
pressHpa = bmp.readPressure() / 100.0f;
bmpC = bmp.readTemperature();
Serial.print(F("Temp="));
Serial.print(tempC, 1);
Serial.print(F("C"));
Serial.print(F(", Humidity="));
Serial.print(humidity, 0);
Serial.print(F("%"));
Serial.print(F(", Pressure="));
Serial.print(pressHpa, 1);
Serial.print(F("hPa"));
Serial.print(F(", Temp="));
Serial.print(bmpC, 1);
Serial.print(F("C"));
Serial.println();
if (cardOk) writeRow();
}
The sketch above runs here on a simulated Arduino Uno. Move the sliders for the sensors and buttons it reads, and watch the Serial monitor, display and outputs change.
Check the DATA wire and the pull-up. The DHT22 needs at least 2 seconds between reads, so do not poll it faster.
Check SDA/SCL are not swapped. Run an I²C scanner sketch to confirm the address.
The coin cell is flat or missing. Some modules need the charging resistor removed when using a CR2032.
Check the card is FAT32, fully inserted, and CS is on the pin in the sketch.
Open the Serial Monitor at 115200 baud and check for messages. Make sure you chose the right board and port in the Arduino IDE.
Close other programs using the serial port, try another USB cable (some are charge-only) and press reset just before uploading.
Yes. Most of the code works unchanged on an ESP32 with the ESP32 board package. Watch for 5 V modules: ESP32 pins are 3.3 V, so 5 V output signals need a resistor divider.
Use a 5 V USB phone charger or a power bank into the board's USB port.
9 parts: Uno R3 CH340G ATmega328p Compatible Development Board, Arduino USB-A to USB-B Data Cable for UNO/MEGA, DHT22 Temperature & Humidity Sensor, BMP280 Temperature & Barometric Pressure Sensor Module, DS3231 Precision RTC Module with EEPROM, DFRobot Fermion MicroSD Card Module – SPI, microSD Memory Card Class 10 (16GB), Solderless Breadboard (830 points) and Dupont Jumper Wires (40 pcs). Tools: Digital Multimeter and Wire Stripper and Cutter. On this page you can tick the parts you already have and add only the rest to your cart.
It is a intermediate project and takes about 2–3 hours. The build on this page has 9 steps.
No. This page has the complete, tested code (weather_data_logger.ino). Install these libraries first: DHT sensor library, Adafruit Unified Sensor, Adafruit BMP280 Library, RTClib and SD.
Yes. The Run it panel under the code runs this exact sketch on a simulated board. Move the sliders or press the buttons for the sensors it reads, and the Serial monitor, display and outputs react as they will on the real build. It is a simulation, so real readings depend on your parts and wiring.
About ₹1,574 for the parts at the prices on this page, plus tools if you do not have them. Quantity price breaks lower the cost when you build several.
Real-time clocks and backup batteries; SPI devices and CSV logging; Single-wire digital sensors and why some sensors need slow polling; The I²C bus and device addresses.
Ideas that reuse this build: Live Wi-Fi dashboard. They are listed under Take it further on this page.
A kitchen gas sniffer that beeps and flashes the moment LPG levels climb.
See the smoke level live on a crisp screen and get a loud warning when it spikes.
An infrared eye that spots an open flame and raises the alarm.
Walk into the room and it sounds the alarm: the classic first security build.
Learning project. Check every circuit and the datasheet of each part before you power it up.
Temp=26.9C, Humidity=55%, Pressure=1008.2hPa, Temp=25.9C Temp=27.0C, Humidity=55%, Pressure=1008.1hPa, Temp=26.0C Temp=26.9C, Humidity=55%, Pressure=1008.2hPa, Temp=26.0C
A simulation of the sketch above, so you know what to expect. Real readings vary with your parts and wiring.