Shop by category
Shop all componentsWe chose projects that work on a bench in a few hours but leave plenty of room to extend: add logging, a cloud dashboard, more sensors or a custom PCB. Each one uses a different wireless link or sensor type, so a team can pick one that fits its branch.
Check the field soil from your phone and run the pump automatically when it is dry.
Smart irrigation: soil moisture on your phone and a pump that runs only when the field is dry. Covers sensors, relays and automatic control, the most asked-for agriculture IoT topic.
Parts, wiring and code →Rooftop tank level on your phone, from a waterproof sensor in the lid.
Water level monitoring with a waterproof ultrasonic sensor. Easy to extend with pump control, usage graphs or alerts.
Parts, wiring and code →One screen that shows carbon dioxide, air quality index, dust and humidity for a classroom, office or bedroom.
CO2, air quality index, dust and humidity on one screen. Uses UART, I2C and an analog dust sensor, so there is real data to analyse in your report.
Parts, wiring and code →A trail camera for the garden or the front door: every movement gets a photo.
A motion-triggered security camera that saves photos to microSD. Shows image capture and storage on a low-cost board.
Parts, wiring and code →When a door or shutter opens, the ESP32 sends you an SMS over 4G: no Wi-Fi needed at the site.
A door alarm that sends SMS over 4G LTE, with no Wi-Fi at the site. Teaches AT commands and powering a cellular modem.
Parts, wiring and code →See how hard a motor or pump is vibrating on your phone and be warned when it rises.
Condition monitoring: an MPU6050 measures how hard a motor or pump vibrates and warns when it rises. A strong topic for predictive maintenance.
Parts, wiring and code →Sends soil moisture and temperature from the far end of the farm, a kilometre or more, with no Wi-Fi or SIM.
A LoRa sensor node that reports soil data a kilometre or more away without Wi-Fi or a SIM. Pair it with a LoRa receiver for a complete two-node system.
Parts, wiring and code →Clip a Bluetooth beacon to your keys; an ESP32 at the door sees it and switches a light for five minutes.
Bluetooth Low Energy presence detection: a beacon on your keys switches a light when you come home. Good for smart home and RSSI analysis.
Parts, wiring and code →See on your phone when someone at risk of falling has got out of bed.
A healthcare IoT build that alerts a carer's phone when a patient gets out of bed. Simple hardware with a clear social use.
Parts, wiring and code →Speed, distance and ride time from a GPS and BeiDou receiver, plus a 6-axis IMU that notices a hard fall.
GPS speed and distance with an IMU that detects a hard fall: the base for an accident detection and alert system.
Parts, wiring and code →Pick one that solves a real problem you can demonstrate, such as smart irrigation, water level monitoring or air quality monitoring. Examiners look for a working prototype, a clear block diagram, real readings and a list of improvements, more than for an unusual idea.
An ESP32 is the usual choice because it has Wi-Fi and Bluetooth built in and is programmed in the Arduino IDE. Add a 4G modem when there is no Wi-Fi at the site, or LoRa modules for long range at low power.
Build the base project first, then add something of your own: log data to a cloud dashboard, add a second sensor, compare two sensors, run it on solar power, design a PCB, or measure power use and battery life. Each of these gives you results to write about.
The base builds on this list cost from about ₹440 to ₹7,350 in parts. Most are under ₹2,500. The ESP32 board, breadboard and wires can be reused across prototypes.
Yes. ECE and EEE teams can focus on the sensors, power supply and wireless link; CSE teams can focus on the web dashboard, data logging and analysis. All of them start from the same working hardware and code.
No. They are all built and tested on low-voltage DC. Where a project could later switch a mains pump or lamp, the project page explains that the mains side must be wired by a qualified electrician in a closed enclosure.