LPG gas leak alarm
A kitchen gas sniffer that beeps and flashes the moment LPG levels climb.
Shop by category
Shop all componentsStale air makes people sleepy long before it smells. This station combines a real infrared CO2 sensor (Senseair S8), an ENS160 metal-oxide sensor for VOCs with an AHT21 for temperature and humidity, and a Sharp optical dust sensor. An ESP32 reads them all and shows the values on an OLED screen. Open a window when CO2 goes above about 1,000 ppm.
Metal-oxide gas sensors run hot; keep them in a ventilated case.
Tick anything you already have and the total updates.
Senseair S8 NDIR CO2 sensor, UART Modbus
ENS160 air quality plus AHT21 temperature and humidity, I2C
Sharp GP2Y1014AU optical dust sensor
150 ohm for the dust LED and a 10k/20k divider for its output
SGP40 VOC module: an alternative to the ENS160
AHT20 + BMP280 board that adds air pressure
Sensirion SHTC3 for more accurate humidity
HR202 resistive humidity element, for learning how humidity sensing works
MP135 analog air-pollution sensor for a simple alarm
Digital alcohol sensor module for a breath or spirits experiment
Plug-in 0.91 inch OLED if you use the DFRobot Gravity system
Follow the colours: red is power, dark grey is ground, blue is a signal.
air_station.inoVerify & upload in Electrolark#include <Wire.h>
#include <Adafruit_AHTX0.h>
#include <Adafruit_GFX.h>
#include <Adafruit_SSD1306.h>
Adafruit_SSD1306 oled(128, 64, &Wire, -1);
Adafruit_AHTX0 aht;
HardwareSerial s8(2);
const uint8_t ENS = 0x53; // 0x52 if the ADD pin is low
const int DUST_LED = 25, DUST_OUT = 34;
int readCO2() {
const uint8_t cmd[] = {0xFE, 0x04, 0x00, 0x03, 0x00, 0x01, 0xD5, 0xC5};
while (s8.available()) s8.read();
s8.write(cmd, 8);
uint8_t r[7]; int n = 0; unsigned long t = millis();
while (n < 7 && millis() - t < 500) if (s8.available()) r[n++] = s8.read();
return n == 7 ? (r[3] << 8) | r[4] : -1;
}
void ensWrite(uint8_t reg, uint8_t v) { Wire.beginTransmission(ENS); Wire.write(reg); Wire.write(v); Wire.endTransmission(); }
uint16_t ensRead16(uint8_t reg) {
Wire.beginTransmission(ENS); Wire.write(reg); Wire.endTransmission(false);
Wire.requestFrom(ENS, (uint8_t)2);
uint16_t lo = Wire.read(), hi = Wire.read();
return lo | (hi << 8);
}
float readDust() { // relative dust value in volts
digitalWrite(DUST_LED, LOW);
delayMicroseconds(280);
int a = analogRead(DUST_OUT);
delayMicroseconds(40);
digitalWrite(DUST_LED, HIGH);
delayMicroseconds(9680);
return a * 3.3 / 4095.0 * 1.5; // undo the 10k/20k divider
}
void setup() {
Serial.begin(115200);
s8.begin(9600, SERIAL_8N1, 16, 17);
Wire.begin(21, 22);
aht.begin();
ensWrite(0x10, 0x02); // OPMODE = standard
pinMode(DUST_LED, OUTPUT); digitalWrite(DUST_LED, HIGH);
oled.begin(SSD1306_SWITCHCAPVCC, 0x3C);
}
void loop() {
sensors_event_t hum, temp;
aht.getEvent(&hum, &temp);
int co2 = readCO2();
Wire.beginTransmission(ENS); Wire.write(0x21); Wire.endTransmission(false);
Wire.requestFrom(ENS, (uint8_t)1);
int aqi = Wire.read() & 0x07; // 1 excellent ... 5 unhealthy
uint16_t tvoc = ensRead16(0x22);
float dust = 0; for (int i = 0; i < 10; i++) dust += readDust(); dust /= 10;
Serial.printf("CO2 %d ppm AQI %d TVOC %u ppb %.1f C %.0f %%RH dust %.2f V\n",
co2, aqi, tvoc, temp.temperature, hum.relative_humidity, dust);
oled.clearDisplay(); oled.setTextColor(WHITE);
oled.setTextSize(2); oled.setCursor(0, 0); oled.printf("%d ppm", co2);
oled.setTextSize(1); oled.setCursor(0, 20);
oled.printf("AQI %d TVOC %u\n%.1f C %.0f %%RH\nDust %.2f V\n", aqi, tvoc, temp.temperature, hum.relative_humidity, dust);
if (co2 > 1000) oled.print("Open a window");
oled.display();
delay(4000);
}
The sketch above runs here on a simulated ESP32. Move the sliders for the sensors and buttons it reads, and watch the Serial monitor, display and outputs change.
TX and RX are swapped, or the S8 is not powered from 5 V. The S8 needs about 30 seconds after power-up.
Check the I2C address with a scanner: it is 0x53 on most boards and 0x52 when ADD is low.
Check the 150 ohm resistor and 220 µF capacitor on V-LED and the LED pin timing.
No. The Sharp sensor gives a relative voltage. Use it to compare rooms and times, not as an official reading.
It corrects itself over about a week, assuming it sees fresh air at least once in that time.
Yes, add Wi-Fi and post the values to an MQTT broker or a Google Sheet.
15 parts: ESP32-WROOM-32 38-Pin Development Board, S8-0053 Infrared CO2 Sensor Module with Temperature & Humidity – UART/Modbus/PWM, ENS160+AHT21 Air Quality, Temperature & Humidity Sensor Module – I2C Interface, Sharp Microelectronics GP2Y1014AU0F Dust Sensor, Analog Output, High Precision, Range: 0~1500 µg/m³, 0.96" OLED Display 128x64, Resistor Assortment Kit (30 Values), Generic GY-SGP40 Air Quality Sensor Module – SGP40 Metal Oxide Gas Sensor w/ I2C Interface & Header Pin, Generic AHT20+BMP280 Temperature Humidity Air Pressure Module with Soldering Pin – I2C 4P Grove Interface, Sensirion SHTC3 Digital Humidity & Temperature Sensor – I²C Interface, Ultra-Low Power, HR202L Humidity Sensor without shell – Analog Polymer Sensor, plus 5 more. On this page you can tick the parts you already have and add only the rest to your cart.
It is a intermediate project and takes about 3 hours. The build on this page has 6 steps.
No. This page has the complete, tested code (air_station.ino).
Yes. The Run it panel under the code runs this exact sketch on a simulated board. Move the sliders or press the buttons for the sensors it reads, and the Serial monitor, display and outputs react as they will on the real build. It is a simulation, so real readings depend on your parts and wiring.
About ₹4,583 for the parts at the prices on this page. Quantity price breaks lower the cost when you build several.
Reading a Modbus sensor over UART; Raw I2C register reads; Timing the pulsed LED of an optical dust sensor.
Metal-oxide gas sensors run hot; keep them in a ventilated case.
Ideas that reuse this build: M5Stack weather display. They are listed under Take it further on this page.
A kitchen gas sniffer that beeps and flashes the moment LPG levels climb.
See the smoke level live on a crisp screen and get a loud warning when it spikes.
An infrared eye that spots an open flame and raises the alarm.
Walk into the room and it sounds the alarm: the classic first security build.
Learning project. Check every circuit and the datasheet of each part before you power it up.
CO2 -1 ppm AQI 0 TVOC 0 ppb 25.9 C 55 %RH dust 1.49 V
A simulation of the sketch above, so you know what to expect. Real readings vary with your parts and wiring.