Component guide · Beginner · 5 min read
ESP32 DevKit Board (WROOM-32, 30 and 38 Pin)

Pinout, Drivers and First Sketch
By Geekobot Learning Team · Updated 29 Oct 2026
On this page
The ESP32 DevKit is the standard ESP32 board: a WROOM-32 module with Wi-Fi and Bluetooth, a USB to serial chip, a 3.3 V regulator and BOOT and EN buttons. The 38-pin and 30-pin versions differ only in how many pins reach the headers. Install the ESP32 board package, pick ESP32 Dev Module, and the same sketch works on all of them.
Key specs at a glance
- Module
- ESP32-WROOM-32, -32D, -32E, -32U (U = external antenna)
- CPU
- Dual-core Xtensa LX6, 240 MHz, 520 KB RAM, 4 MB flash typical
- Wireless
- Wi-Fi 2.4 GHz, Bluetooth Classic and BLE 4.2
- USB chip
- CP2102, CH340 or CH9102 depending on board
- Logic
- 3.3 V; GPIO not 5 V tolerant
- Power
- 5 V from USB or VIN, 3.3 V regulator on board
Models in this guide
These are alternatives. Pick the one that fits your project; you only need one.
Option 1ESP32-WROOM-32 38-Pin Development Board₹389
Option 2ESP-32 Development Board w/ CH9102X & Type-C USB₹448
Option 3ESP-32 Development Board with CP2102 USB-to-Serial & Type-C Interface₹399
Option 4ESP32-DEVKITC Core Board w/ ESP32-WROOM-VE Module₹2,038
Option 5ESP32-WROOM-32D IoT Development Board Module w/ Onboard Antenna₹639
Option 6ESP32-WROOM-32E Development Board Module w/ On-Board Antenna₹1,725
What the ESP32 DevKit board (WROOM-32) is
All these boards run the same code; differences are the USB chip (driver), pin count, antenna type and flash size. Espressif's own DevKitC and DevKitM boards are the reference versions; WeAct, LOLIN D32, NodeMCU-32S and others follow the same layout with small changes.
Avoid GPIO 6 to 11 (flash), take care with strapping pins 0, 2, 5, 12 and 15 at boot, and note that GPIO 34 to 39 are input only with no pull-ups. ADC2 pins stop working while Wi-Fi is on, so use ADC1 (GPIO 32 to 39) for analog sensors.
ESP32 DevKit board (WROOM-32) pinout
The pins on the ESP32 DevKit board (WROOM-32) and what each one does.
| Pin | Function |
|---|---|
| 3V3 / GND | 3.3 V output and ground |
| VIN / 5V | 5 V input (or USB 5 V out) |
| EN | Reset (button) |
| GPIO 0 | BOOT button, low at reset enters download mode |
| GPIO 21 / 22 | Default I2C SDA / SCL |
| GPIO 18, 19, 23, 5 | Default SPI SCK, MISO, MOSI, CS |
| GPIO 1 / 3 | UART0 TX / RX (USB serial) |
| GPIO 34 to 39 | Input only, ADC1 |
- 3V3 / GND
- 3.3 V output and ground
- VIN / 5V
- 5 V input (or USB 5 V out)
- EN
- Reset (button)
- GPIO 0
- BOOT button, low at reset enters download mode
- GPIO 21 / 22
- Default I2C SDA / SCL
- GPIO 18, 19, 23, 5
- Default SPI SCK, MISO, MOSI, CS
- GPIO 1 / 3
- UART0 TX / RX (USB serial)
- GPIO 34 to 39
- Input only, ADC1
Wiring the ESP32 DevKit board (WROOM-32)
This table shows an I2C sensor on the default pins. The middle column is unused here; any 3.3 V I2C sensor connects to GPIO 21 and 22. Never put 5 V on a GPIO.
| ESP32 DevKit board (WROOM-32) pin | I2C sensor | ESP32 DevKit |
|---|---|---|
| VCC | 5V (or 3.3V) | 3V3 |
| GND | GND | GND |
| SDA | A4 | GPIO 21 |
| SCL | A5 | GPIO 22 |
- VCC
- I2C sensor:
- 5V (or 3.3V)
- ESP32 DevKit:
- 3V3
- GND
- I2C sensor:
- GND
- ESP32 DevKit:
- GND
- SDA
- I2C sensor:
- A4
- ESP32 DevKit:
- GPIO 21
- SCL
- I2C sensor:
- A5
- ESP32 DevKit:
- GPIO 22
Example code
In Arduino IDE add the Espressif board URL, install esp32, select ESP32 Dev Module and the right COM port. The LED pin is 2 on most boards; some have no user LED.
#include <WiFi.h>
const char* ssid = "YOUR_WIFI";
const char* pass = "YOUR_PASSWORD";
void setup() {
Serial.begin(115200);
pinMode(2, OUTPUT); // on-board LED on most DevKit boards
WiFi.begin(ssid, pass);
while (WiFi.status() != WL_CONNECTED) { delay(300); Serial.print("."); }
Serial.println(); Serial.println(WiFi.localIP());
}
void loop() {
digitalWrite(2, !digitalRead(2));
delay(500);
}Setup and tuning
CP2102 boards need the Silicon Labs driver on older Windows; CH340/CH9102 boards need the WCH driver.
Hold BOOT while the upload starts, or add a 10 uF capacitor between EN and GND on boards that do not auto-reset.
the 38-pin board covers both rails of a normal breadboard; use two breadboards or an expansion board.
the 32U and 32UE boards need an IPEX antenna fitted.
What you need
Shop this list20 of 20 found in our store · ₹22,261
ESP32-WROOM-32 38-Pin Development Board: the part this guide coversESP32-WROOM-32 38-Pin Development Board₹389
ESP-32 Development Board w/ CH9102X & Type-C USB: another version this guide coversESP-32 Development Board w/ CH9102X & Type-C USB₹448
ESP-32 Development Board with CP2102 USB-to-Serial & Type-C Interface: another version this guide coversESP-32 Development Board with CP2102 USB-to-Serial & Type-C Interface₹399
ESP32-DEVKITC Core Board w/ ESP32-WROOM-VE Module: another version this guide coversESP32-DEVKITC Core Board w/ ESP32-WROOM-VE Module₹2,038
ESP32-WROOM-32D IoT Development Board Module w/ Onboard Antenna: another version this guide coversESP32-WROOM-32D IoT Development Board Module w/ Onboard Antenna₹639
ESP32-WROOM-32E Development Board Module w/ On-Board Antenna: another version this guide coversESP32-WROOM-32E Development Board Module w/ On-Board Antenna₹1,725
ESP32-WROOM-32U Wi-Fi + Bluetooth IoT Development Board: another version this guide coversESP32-WROOM-32U Wi-Fi + Bluetooth IoT Development Board₹469
ESP32-WROOM-32UE Wi-Fi + Bluetooth LE MCU Development Board: another version this guide coversESP32-WROOM-32UE Wi-Fi + Bluetooth LE MCU Development Board₹1,572
Espressif ESP32-DevKitC-32E Development Board: another version this guide coversEspressif ESP32-DevKitC-32E Development Board₹1,123
Espressif ESP32-DevKitC-32UE Development Board w/ External Antenna Connector: another version this guide coversEspressif ESP32-DevKitC-32UE Development Board w/ External Antenna Connector₹1,119
Espressif ESP32-DevKitC-VE Development Board w/ 8MB PSRAM: another version this guide coversEspressif ESP32-DevKitC-VE Development Board w/ 8MB PSRAM₹1,149
Espressif ESP32-DevKitM-1 Development Board: another version this guide coversEspressif ESP32-DevKitM-1 Development Board₹1,143
Espressif ESP32-DevKitM-1U Development Board: another version this guide coversEspressif ESP32-DevKitM-1U Development Board₹1,043
NodeMCU ESP-32S ESP-32E WiFi & Bluetooth Development Board: another version this guide coversNodeMCU ESP-32S ESP-32E WiFi & Bluetooth Development Board₹1,609
ESP-WROOM-32 Wi-Fi Module Development Board (No BLE): another version this guide coversESP-WROOM-32 Wi-Fi Module Development Board (No BLE)₹349
ESP32-SOLO-1 IoT Development Board Module: another version this guide coversESP32-SOLO-1 IoT Development Board Module₹1,580
Wemos LOLIN D32 V1.0.0 ESP32-WROOM-32 Dev Board: another version this guide coversWemos LOLIN D32 V1.0.0 ESP32-WROOM-32 Dev Board₹519
WeAct Studio ESP32-DOWD-V3 Development Board Type-C CH340K: another version this guide coversWeAct Studio ESP32-DOWD-V3 Development Board Type-C CH340K₹549
Elecrow ESP32S WiFi BLE Board V1.0: another version this guide coversElecrow ESP32S WiFi BLE Board V1.0₹1,486
Cytron Technologies NANO32 ESP32 IoT Development Board: another version this guide coversCytron Technologies NANO32 ESP32 IoT Development Board₹2,913
Alternatives and when to choose them
- ESP32 overview: variants and which board to choose.
- ESP32-S3 DevKitC: newer chip with USB and AI instructions.
- ESP32 expansion boards: screw terminals for DevKit boards.
Common mistakes to avoid
- Using a charge-only USB cable.
- Putting 5 V sensors on GPIO pins.
- Reading analog pins on ADC2 while Wi-Fi is on.
- Using GPIO 6 to 11, which crashes the board.
Frequently asked questions
30-pin or 38-pin?
Same chip; the 38-pin exposes a few more GPIOs.
Which board do I select?
ESP32 Dev Module for nearly all of them.
Can it run on a battery?
Yes, through 3V3 from a regulated supply or VIN, but the USB chip and LED waste power in sleep.
What is the difference between 32D and 32E?
32E is a newer silicon revision with fixes; code is the same.
Can I use MicroPython?
Yes, flash the ESP32 MicroPython firmware with esptool or Thonny.
Parts for this guide
Keep learning
Sources
Written by the Geekobot team from manufacturer datasheets. Always check the datasheet for the exact part and variant you buy.






