Component guide · Advanced · 5 min read
ESP32-WROOM-32 Module (32D, 32E, 32U)

Minimum Circuit, Flashing and PCB Tips
By Geekobot Learning Team · Updated 29 Oct 2026
On this page
The ESP32-WROOM-32 is the bare castellated module used on ESP32 DevKit boards: chip, flash, crystal and antenna under a metal can. On your own PCB it needs only a clean 3.3 V supply of at least 500 mA, a pull-up and capacitor on EN, a BOOT button on GPIO 0 and a UART for flashing. The U versions have an IPEX connector for an external antenna.
Key specs at a glance
- Chip
- ESP32-D0WD(-V3), dual-core 240 MHz
- Flash
- 4, 8 or 16 MB (N4, N8, N16)
- Antenna
- PCB antenna (32, 32D, 32E) or IPEX (32U, 32UE)
- Supply
- 3.0 to 3.6 V, 500 mA peak during Wi-Fi transmit
- Size
- 18 x 25.5 mm, 38 castellated pads
- Certification
- Pre-certified module, simplifies product approval
Models in this guide
These are alternatives. Pick the one that fits your project; you only need one.
Option 1ESP-WROOM-32 Wi-Fi & Bluetooth MCU Module w/ PCB Antenna₹399
Option 2ESP32 WROOM Module v1.1 w/ PCB Antenna₹379
Option 3ESP32-WROOM-32 4M 32Mbit Flash WiFi Bluetooth Module₹299
Option 4ESP32-WROOM-32 8M 64Mbit WiFi Bluetooth Module₹349
Option 5ESP32-WROOM-32 WiFi Bluetooth Module w/ 16M16M 128Mbit Flash₹379
Option 6ESP32-WROOM-32D 4M 32Mbit Flash WiFi Bluetooth Module₹279
What the ESP32-WROOM-32 module is
The minimum circuit is: 3.3 V regulator (AMS1117 or better, 500 mA+), 10 uF and 100 nF at the 3V3 pin, 10 k pull-up from EN to 3V3 with 1 uF to ground, 10 k pull-up on GPIO 0 with a button to ground, and TX0/RX0 brought out for flashing.
Keep copper and ground pour away from the antenna end, and let the antenna overhang the board edge. The adapter boards and burn fixtures here let you flash a module before soldering it.
ESP32-WROOM-32 module pinout
The pins on the ESP32-WROOM-32 module and what each one does.
| Pin | Function |
|---|---|
| 3V3 / GND | Supply |
| EN | Enable/reset (pull-up and capacitor) |
| IO0 | Boot mode; low at reset = download |
| TXD0 / RXD0 | UART0 for flashing and logs |
| IO2, IO12, IO15 | Strapping pins, keep default levels at boot |
| SD0 to SD3, CLK, CMD | Internal flash, do not use |
- 3V3 / GND
- Supply
- EN
- Enable/reset (pull-up and capacitor)
- IO0
- Boot mode; low at reset = download
- TXD0 / RXD0
- UART0 for flashing and logs
- IO2, IO12, IO15
- Strapping pins, keep default levels at boot
- SD0 to SD3, CLK, CMD
- Internal flash, do not use
Wiring the ESP32-WROOM-32 module
Use a 3.3 V USB to TTL adapter and a supply that can give 500 mA. Hold IO0 low, pulse EN low, then release EN to enter download mode.
| ESP32-WROOM-32 module pin | USB to TTL adapter | Breakout board |
|---|---|---|
| 3V3 | 3.3V (adapter's 3.3 V may be too weak; use a separate 3.3 V supply) | 3V3 |
| GND | GND | GND |
| TXD0 | RX | - |
| RXD0 | TX | - |
| IO0 | GND while resetting to flash | - |
| EN | 10k pull-up to 3V3 | - |
- 3V3
- USB to TTL adapter:
- 3.3V (adapter's 3.3 V may be too weak; use a separate 3.3 V supply)
- Breakout board:
- 3V3
- GND
- USB to TTL adapter:
- GND
- Breakout board:
- GND
- TXD0
- USB to TTL adapter:
- RX
- Breakout board:
- -
- RXD0
- USB to TTL adapter:
- TX
- Breakout board:
- -
- IO0
- USB to TTL adapter:
- GND while resetting to flash
- Breakout board:
- -
- EN
- USB to TTL adapter:
- 10k pull-up to 3V3
- Breakout board:
- -
Example code
Arduino and ESP-IDF call esptool for you; manual commands are handy for factory flashing or MicroPython. Use 0x0 instead of 0x1000 for merged images.
pip install esptool
esptool.py --chip esp32 --port COM5 erase_flash
esptool.py --chip esp32 --port COM5 --baud 460800 write_flash 0x1000 firmware.bin
# or upload from Arduino IDE with board 'ESP32 Dev Module'Setup and tuning
select the right size (4, 8 or 16 MB) in Arduino or ESP-IDF.
fit an antenna before transmitting on U versions.
brown-outs during Wi-Fi start are almost always a weak 3.3 V supply.
a burn fixture (pogo-pin jig) flashes modules quickly before assembly.
What you need
Shop this list20 of 20 found in our store · ₹7,222
ESP-WROOM-32 Wi-Fi & Bluetooth MCU Module w/ PCB Antenna: the part this guide coversESP-WROOM-32 Wi-Fi & Bluetooth MCU Module w/ PCB Antenna₹399
ESP32 WROOM Module v1.1 w/ PCB Antenna: another version this guide coversESP32 WROOM Module v1.1 w/ PCB Antenna₹379
ESP32-WROOM-32 4M 32Mbit Flash WiFi Bluetooth Module: another version this guide coversESP32-WROOM-32 4M 32Mbit Flash WiFi Bluetooth Module₹299
ESP32-WROOM-32 8M 64Mbit WiFi Bluetooth Module: another version this guide coversESP32-WROOM-32 8M 64Mbit WiFi Bluetooth Module₹349
ESP32-WROOM-32 WiFi Bluetooth Module w/ 16M16M 128Mbit Flash: another version this guide coversESP32-WROOM-32 WiFi Bluetooth Module w/ 16M16M 128Mbit Flash₹379
ESP32-WROOM-32D 4M 32Mbit Flash WiFi Bluetooth Module: another version this guide coversESP32-WROOM-32D 4M 32Mbit Flash WiFi Bluetooth Module₹279
ESP32-WROOM-32D 8M 64Mbit Flash WiFi Bluetooth 4.2 Module: another version this guide coversESP32-WROOM-32D 8M 64Mbit Flash WiFi Bluetooth 4.2 Module₹349
ESP32-WROOM-32D WiFi Bluetooth Module 16M 128Mbit Flash: another version this guide coversESP32-WROOM-32D WiFi Bluetooth Module 16M 128Mbit Flash₹407
ESP32-WROOM-32E 16M 128Mbit Flash WiFi Bluetooth Module: another version this guide coversESP32-WROOM-32E 16M 128Mbit Flash WiFi Bluetooth Module₹459
ESP32-WROOM-32E WiFi Bluetooth Module 8M 64Mbit Flash: another version this guide coversESP32-WROOM-32E WiFi Bluetooth Module 8M 64Mbit Flash₹359
ESP32-WROOM-32U 4M 128Mbit WiFi Bluetooth Module w/ U.FL Connector: another version this guide coversESP32-WROOM-32U 4M 128Mbit WiFi Bluetooth Module w/ U.FL Connector₹559
ESP32-WROOM-32U 4M 32Mbit WiFi Bluetooth Module w/ U.FL Connector: another version this guide coversESP32-WROOM-32U 4M 32Mbit WiFi Bluetooth Module w/ U.FL Connector₹349
ESP32-WROOM-32U 8M 64Mbit WiFi Bluetooth Module w/ U.FL Connector: another version this guide coversESP32-WROOM-32U 8M 64Mbit WiFi Bluetooth Module w/ U.FL Connector₹347
SM-ESP32E Wi-Fi + Bluetooth Module w/ 4M 32Mbit Flash: another version this guide coversSM-ESP32E Wi-Fi + Bluetooth Module w/ 4M 32Mbit Flash₹309
Espressif ESP32-WROOM-32E-N16 Wi-Fi + Bluetooth MCU Module: another version this guide coversEspressif ESP32-WROOM-32E-N16 Wi-Fi + Bluetooth MCU Module₹399
Espressif ESP32-WROOM-32E-N4 Wi-Fi & Bluetooth 5.0 Module: another version this guide coversEspressif ESP32-WROOM-32E-N4 Wi-Fi & Bluetooth 5.0 Module₹349
Espressif ESP32-WROOM-32E-N8 Wi-Fi & BLE Module: another version this guide coversEspressif ESP32-WROOM-32E-N8 Wi-Fi & BLE Module₹369
Espressif ESP32-WROOM-32UE-N16 Wi-Fi + Bluetooth Module: another version this guide coversEspressif ESP32-WROOM-32UE-N16 Wi-Fi + Bluetooth Module₹399
AI-Thinker ESP32-S Wi-Fi + Bluetooth 4.2 SoC Module w/ PCB Antenna: another version this guide coversAI-Thinker ESP32-S Wi-Fi + Bluetooth 4.2 SoC Module w/ PCB Antenna₹459
ESP32 ESP-Wroom-32 Adapter Breakout Board: another version this guide coversESP32 ESP-Wroom-32 Adapter Breakout Board₹25
Alternatives and when to choose them
- ESP32 DevKit board: the same module on a ready board.
- ESP32-WROVER module: adds PSRAM.
- ESP32-S3-WROOM-1: the newer module with native USB.
Common mistakes to avoid
- Powering from a USB to TTL adapter's weak 3.3 V pin.
- Ground pour under the antenna.
- No pull-up on EN, causing random resets.
- Using flash pins as GPIO.
Frequently asked questions
What do 32D and 32E mean?
Chip revisions; 32E uses the V3 silicon with bug fixes.
Do I need a crystal?
No, it is inside the module.
How much current does it need?
About 80 mA average with Wi-Fi and peaks near 500 mA.
Can I solder it by hand?
Yes, the castellated pads are 1.27 mm pitch.
Is the module certified?
Yes, it carries Espressif's radio certifications, but your product still needs its own checks.
Parts for this guide
Keep learning
Sources
Written by the Geekobot team from manufacturer datasheets. Always check the datasheet for the exact part and variant you buy.






