Component guide · Advanced · 4 min read
ESP32-S3-WROOM-1 and S3-MINI-1 Modules

Minimum Circuit and Native USB Flashing
By Geekobot Learning Team · Updated 29 Oct 2026
On this page
The ESP32-S3-WROOM-1 is the module behind most ESP32-S3 boards, with flash and optional PSRAM inside. Its big advantage on a custom PCB is native USB: wire GPIO 19 and 20 to a USB-C socket and you can flash and debug without a USB to serial chip. Add a 3.3 V regulator, EN pull-up and capacitor, and a BOOT button on GPIO 0.
Key specs at a glance
- Chip
- ESP32-S3, dual-core 240 MHz
- Memory
- N4, N8, N16 flash; R2 quad or R8 octal PSRAM
- Antenna
- PCB (WROOM-1) or IPEX (WROOM-1U)
- USB
- Full-speed USB OTG and USB serial/JTAG
- Supply
- 3.0 to 3.6 V, 500 mA peak
- Smaller options
- ESP32-S3-MINI-1, M5Stamp S3, NanoS3
Models in this guide
These are alternatives. Pick the one that fits your project; you only need one.
Option 1Espressif ESP32-S3-WROOM-1-N16R8 Wi-Fi & Bluetooth LE AIoT Module₹449
Option 2Espressif ESP32-S3-WROOM-1-N8R8 Wi-Fi & BLE 5.0 AIoT Module₹409
Option 3Espressif ESP32-S3-WROOM-1-N4R8 Wi-Fi & BLE Module₹419
Option 4Espressif ESP32-S3-WROOM-1U-N16R8 Wi-Fi & Bluetooth LE Module₹469
Option 5Espressif ESP32-S3-WROOM-1U-N8R8 Wi-Fi & BLE 5.0 AIoT Module₹409
Option 6Espressif ESP32-S3-WROOM-1U-N4R8 Wi-Fi & BLE 5.0 Module₹399
What the ESP32-S3-WROOM-1 module is
The built-in USB serial/JTAG controller lets the module enumerate as a COM port and accept uploads straight away, even with a blank flash. Add a 22 ohm series resistor on each data line, ESD protection, and 5.1 k CC resistors on the USB-C socket.
Octal PSRAM versions (R8) use GPIO 35 to 37. Stamp modules such as the M5Stamp S3 and NanoS3 put the module on a tiny carrier for hand soldering.
ESP32-S3-WROOM-1 module pinout
The pins on the ESP32-S3-WROOM-1 module and what each one does.
| Pin | Function |
|---|---|
| 3V3 / GND | Supply |
| EN | Reset (10k pull-up, 1 uF) |
| IO0 | BOOT |
| IO19 / IO20 | USB D- / D+ |
| IO43 / IO44 | UART0 TX / RX |
| IO45, IO46, IO3 | Strapping pins |
- 3V3 / GND
- Supply
- EN
- Reset (10k pull-up, 1 uF)
- IO0
- BOOT
- IO19 / IO20
- USB D- / D+
- IO43 / IO44
- UART0 TX / RX
- IO45, IO46, IO3
- Strapping pins
Wiring the ESP32-S3-WROOM-1 module
Keep the antenna end clear of copper. A 500 mA or larger 3.3 V regulator with 10 uF and 100 nF capacitors next to the module is the minimum.
| ESP32-S3-WROOM-1 module pin | USB-C socket | Notes |
|---|---|---|
| IO19 | USB D- | - |
| IO20 | USB D+ | - |
| 3V3 | 3.3 V regulator output | - |
| IO0 | BOOT button to GND | - |
| EN | Reset button to GND, 10k to 3V3 | - |
- IO19
- USB-C socket:
- USB D-
- Notes:
- -
- IO20
- USB-C socket:
- USB D+
- Notes:
- -
- 3V3
- USB-C socket:
- 3.3 V regulator output
- Notes:
- -
- IO0
- USB-C socket:
- BOOT button to GND
- Notes:
- -
- EN
- USB-C socket:
- Reset button to GND, 10k to 3V3
- Notes:
- -
Example code
If the port does not appear, hold BOOT while plugging in USB. After your sketch enables TinyUSB, the port name can change.
esptool.py --chip esp32s3 --port COM7 erase_flash
esptool.py --chip esp32s3 --port COM7 write_flash 0x0 firmware.bin
# Arduino: board ESP32S3 Dev Module, USB Mode: Hardware CDC and JTAGSetup and tuning
match flash size and PSRAM mode (QSPI for R2, OPI for R8).
add 5.1 k pull-downs on CC1 and CC2 or chargers will not supply 5 V.
OpenOCD works over the built-in USB JTAG, no probe needed.
fit an antenna on 1U versions.
What you need
Shop this list17 of 17 found in our store · ₹79,285
Espressif ESP32-S3-WROOM-1-N16R8 Wi-Fi & Bluetooth LE AIoT Module: the part this guide coversEspressif ESP32-S3-WROOM-1-N16R8 Wi-Fi & Bluetooth LE AIoT Module₹449
Espressif ESP32-S3-WROOM-1-N8R8 Wi-Fi & BLE 5.0 AIoT Module: another version this guide coversEspressif ESP32-S3-WROOM-1-N8R8 Wi-Fi & BLE 5.0 AIoT Module₹409
Espressif ESP32-S3-WROOM-1-N4R8 Wi-Fi & BLE Module: another version this guide coversEspressif ESP32-S3-WROOM-1-N4R8 Wi-Fi & BLE Module₹419
Espressif ESP32-S3-WROOM-1U-N16R8 Wi-Fi & Bluetooth LE Module: another version this guide coversEspressif ESP32-S3-WROOM-1U-N16R8 Wi-Fi & Bluetooth LE Module₹469
Espressif ESP32-S3-WROOM-1U-N8R8 Wi-Fi & BLE 5.0 AIoT Module: another version this guide coversEspressif ESP32-S3-WROOM-1U-N8R8 Wi-Fi & BLE 5.0 AIoT Module₹409
Espressif ESP32-S3-WROOM-1U-N4R8 Wi-Fi & BLE 5.0 Module: another version this guide coversEspressif ESP32-S3-WROOM-1U-N4R8 Wi-Fi & BLE 5.0 Module₹399
ESP32-S3-N8R2 Wi-Fi & Bluetooth LE Module: another version this guide coversESP32-S3-N8R2 Wi-Fi & Bluetooth LE Module₹529
Espressif ESP32-S3-MINI-1-N8 Wi-Fi & BLE MCU Module w/ PCB Antenna: another version this guide coversEspressif ESP32-S3-MINI-1-N8 Wi-Fi & BLE MCU Module w/ PCB Antenna₹399
ESP32-S3-MOD-8M Module (8MB Flash, Wi-Fi & BLE 5): another version this guide coversESP32-S3-MOD-8M Module (8MB Flash, Wi-Fi & BLE 5)₹413
M5Stack M5Stamp ESP32S3 Module w/ 8MB Flash & 3D Antenna: another version this guide coversM5Stack M5Stamp ESP32S3 Module w/ 8MB Flash & 3D Antenna₹1,209
M5Stack M5StampS3A ESP32-S3 Wi-Fi IoT Module: another version this guide coversM5Stack M5StampS3A ESP32-S3 Wi-Fi IoT Module₹1,189
Unexpected Maker NanoS3 ESP32-S3 IoT Module – Ultra Compact WiFi + Bluetooth Dev Board with 8MB PSRAM: another version this guide coversUnexpected Maker NanoS3 ESP32-S3 IoT Module – Ultra Compact WiFi + Bluetooth Dev Board with 8MB PSRAM₹1,359
USB Type-C cable 1 m: a data cable for programming (not charge-only)24-Core USB Type-C Cable, 1 m₹500Closest match, check the specs
Breadboard power supply module 3.3V/5V: a 3.3 V supply for bare modulesBreadboard Power Supply Module (3.3V / 5V)₹71
USB to TTL serial converter: to talk to the module from a PCUSB to TTL Serial Converter (CH340G / CP2102 / FT232RL / PL2303)₹85Closest match, check the specs
Digital multimeter: to check supply and signal voltagesDigital Multimeter₹177
ESP32-S3 DevKitC-1 N8R8: a reference board to test code firstKikobot C1 6-Axis Robotic Arm for Education and Research₹70,800
Alternatives and when to choose them
- ESP32-S3 DevKitC: the module on a ready board.
- ESP32-WROOM-32 module: the older module without native USB.
- ESP32-S3 Zero and Mini: tiny ready boards.
Common mistakes to avoid
- Missing CC resistors on USB-C.
- Wiring peripherals to the octal PSRAM pins.
- Weak 3.3 V regulator.
- Copper under the antenna.
Frequently asked questions
Do I need a USB to serial chip?
No, native USB can program and print serial.
N8R8 or N16R8?
N16R8 for large apps or files; same price class.
What is the MINI-1?
A smaller module with the same chip, PCB antenna and 8 MB flash.
Is it certified?
Yes, as a module; your product still needs its own approval.
Can I use USB and UART together?
Yes, UART0 stays on GPIO 43 and 44.
Parts for this guide
Keep learning
Sources
Written by the Geekobot team from manufacturer datasheets. Always check the datasheet for the exact part and variant you buy.

