Comparison · Beginner · 3 min read
ESP32-S3, C3, C6 and Other ESP32 Variants
Which One to Choose
By Geekobot Learning Team · Updated 29 Oct 2026
On this page
Choose the ESP32-S3 for cameras, displays, USB and AI work, the ESP32-C3 for cheap small Wi-Fi and BLE projects, and the ESP32-C6 for Wi-Fi 6 plus Thread or Zigbee. The original ESP32 is still the most widely supported and the only one with classic Bluetooth. Read the module name: N8R8 means 8 MB flash and 8 MB PSRAM.
Key specs at a glance
- ESP32 (original)
- Dual Xtensa LX6, Wi-Fi 4, Bluetooth classic and BLE
- ESP32-S2
- Single Xtensa LX7, Wi-Fi 4, USB OTG, no Bluetooth
- ESP32-S3
- Dual Xtensa LX7, Wi-Fi 4, BLE 5, USB OTG, AI vector instructions, up to 8 MB octal PSRAM
- ESP32-C3
- Single RISC-V, Wi-Fi 4, BLE 5, low cost
- ESP32-C6
- RISC-V, Wi-Fi 6, BLE 5, 802.15.4 (Thread and Zigbee)
- ESP32-H2
- RISC-V, BLE 5, 802.15.4, no Wi-Fi
The family at a glance
All of them run the Espressif IDF and work with the Arduino core, so code mostly ports between them. The differences are in the CPU, radios and how many pins are available.
| Chip | CPU | Wireless | Notable features | Pick it for |
|---|---|---|---|---|
| ESP32 | 2 × Xtensa LX6, up to 240 MHz | Wi-Fi 4, BT classic, BLE 4.2 | Widest library support | General projects, Bluetooth audio |
| ESP32-S2 | 1 × Xtensa LX7 | Wi-Fi 4 | USB OTG, no Bluetooth | USB devices, low-cost Wi-Fi |
| ESP32-S3 | 2 × Xtensa LX7 | Wi-Fi 4, BLE 5 | USB OTG, camera and LCD interfaces, vector instructions, PSRAM | Cameras, touch displays, voice and AI |
| ESP32-C3 | 1 × RISC-V, 160 MHz | Wi-Fi 4, BLE 5 | Small and cheap, USB serial/JTAG | Sensors, smart plugs, simple IoT |
| ESP32-C6 | 1 × RISC-V, 160 MHz | Wi-Fi 6, BLE 5, 802.15.4 | Thread and Zigbee support, Matter | Smart home devices |
| ESP32-H2 | 1 × RISC-V, 96 MHz | BLE 5, 802.15.4 | No Wi-Fi | Thread or Zigbee end nodes |
- ESP32
- CPU:
- 2 × Xtensa LX6, up to 240 MHz
- Wireless:
- Wi-Fi 4, BT classic, BLE 4.2
- Notable features:
- Widest library support
- Pick it for:
- General projects, Bluetooth audio
- ESP32-S2
- CPU:
- 1 × Xtensa LX7
- Wireless:
- Wi-Fi 4
- Notable features:
- USB OTG, no Bluetooth
- Pick it for:
- USB devices, low-cost Wi-Fi
- ESP32-S3
- CPU:
- 2 × Xtensa LX7
- Wireless:
- Wi-Fi 4, BLE 5
- Notable features:
- USB OTG, camera and LCD interfaces, vector instructions, PSRAM
- Pick it for:
- Cameras, touch displays, voice and AI
- ESP32-C3
- CPU:
- 1 × RISC-V, 160 MHz
- Wireless:
- Wi-Fi 4, BLE 5
- Notable features:
- Small and cheap, USB serial/JTAG
- Pick it for:
- Sensors, smart plugs, simple IoT
- ESP32-C6
- CPU:
- 1 × RISC-V, 160 MHz
- Wireless:
- Wi-Fi 6, BLE 5, 802.15.4
- Notable features:
- Thread and Zigbee support, Matter
- Pick it for:
- Smart home devices
- ESP32-H2
- CPU:
- 1 × RISC-V, 96 MHz
- Wireless:
- BLE 5, 802.15.4
- Notable features:
- No Wi-Fi
- Pick it for:
- Thread or Zigbee end nodes
Reading board and module names
Espressif's module families. A trailing U (as in WROOM-1U) means a connector for an external antenna instead of a PCB antenna.
flash size in MB.
PSRAM size in MB. N8R8 therefore has 8 MB flash and 8 MB PSRAM.
Espressif development boards with USB and the pins broken out.
the S3 exposes many more GPIOs than the C3, which is limited to about 22.
Which should I buy?
S3 with PSRAM. See ESP32-CAM and touchscreen boards.
C3, and read deep sleep tips.
C6 or H2.
original ESP32.
any ESP32 DevKit; the most tutorials target the original ESP32 and S3.
Practical notes
- Use the matching board definition in the Arduino IDE or PlatformIO. A sketch built for one variant will not run on another.
- Some pins are reserved for flash and PSRAM on S3 modules (especially octal PSRAM). Check the module data sheet before using GPIO 26 to 37 on S3.
- Strapping pins control boot mode; keep them free of external pull-ups. See ESP32 basics and ESP32 vs ESP8266.
Try it: Esp32 pwm resolution calculator
Change the values and the diagram and results update as you type.
Common mistakes to avoid
- Choosing an S3 module without PSRAM for a camera project.
- Expecting Bluetooth classic on an S3, C3 or C6.
- Using pins that are tied to PSRAM or flash.
- Uploading a sketch compiled for the wrong chip.
- Buying a -U module without an antenna.
Frequently asked questions
ESP32-S3 or ESP32-C3?
C3 is cheaper and enough for simple sensors. S3 is more powerful and has more pins, PSRAM and camera and display interfaces.
Does ESP32-C6 have Zigbee?
Yes, the 802.15.4 radio supports Zigbee and Thread, along with Wi-Fi 6 and BLE 5.
What does N8R8 mean?
8 MB flash and 8 MB PSRAM.
Can I run MicroPython on all of them?
Yes, MicroPython supports the main variants, though feature support varies by chip.
Is the original ESP32 outdated?
No, it remains well supported. Newer chips add features, but it is still a safe choice for most projects.
Parts for this guide
Calculators
Terms in this guide
Projects that use it
Put this into practice: 7 step-by-step builds in our project library use parts from this guide.
Keep learning
Sources
Written by the Geekobot team from manufacturer datasheets. Always check the datasheet for the exact part and variant you buy.




