Component guide · Beginner · 4 min read
Waveshare ESP32-S3-Zero and ESP32-S3 Mini Boards

Pinout and Setup
By Geekobot Learning Team · Updated 29 Oct 2026
On this page
ESP32-S3 Zero and Mini boards squeeze a full ESP32-S3 onto a thumb-sized board with a USB-C port, BOOT and reset buttons and an RGB LED. Most use the ESP32-S3FH4R2, with 4 MB flash and 2 MB PSRAM inside the chip, and program over native USB. They are ideal for wearables, keyboards, small sensors and anything where a DevKit is too big.
Key specs at a glance
- Chip
- ESP32-S3FH4R2 (4 MB flash, 2 MB PSRAM) or S3 with external N8R8
- USB
- Native USB-C, no UART chip
- GPIO
- About 18 to 24 pins on headers or castellated pads
- LED
- WS2812 RGB (GPIO 21 on Waveshare Zero)
- Size
- About 18 x 23 mm (Zero)
- Power
- 5 V USB or 3.7 V battery on some boards
Models in this guide
These are alternatives. Pick the one that fits your project; you only need one.
Option 1Waveshare ESP32-S3-Zero-N8R8 Mini Development Board, ESP32-S3 Dual-Core, 8MB Flash/PSRAM₹969
Option 2Waveshare ESP32-S3 Mini Dev Board w/ 8MB Flash & 8MB PSRAM₹849
Option 3Waveshare ESP32-S3 Mini Dev Board w/ ESP32-S3-PICO-1-N8R8, 8MB Flash & PSRAM₹929
Option 4Waveshare ESP32-S3 Mini Development Board w/ ESP32-S3FH4R2₹759
Option 5Waveshare ESP32-S3 Mini Development Board w/ ESP32-S3FH4R2 4MB Flash 2MB PSRAM₹719
Option 6Waveshare ESP32-S3 Mini Development Board w/ ESP32-S3FH4R2, 240MHz, Wi-Fi & BLE 5₹609
What the ESP32-S3 Zero and Mini board is
Because there is no UART bridge, the board appears as a USB device created by the chip. If a sketch crashes early or turns off USB, the port vanishes; hold BOOT while plugging in to get it back.
Castellated edges let the Zero be soldered flat onto your own PCB. Unexpected Maker TinyS3 and Adafruit QT Py S3 are similar small boards with extra battery or STEMMA QT features.
ESP32-S3 Zero and Mini board pinout
The pins on the ESP32-S3 Zero and Mini board and what each one does.
| Pin | Function |
|---|---|
| 5V / 3V3 / GND | Power |
| GPIO 0 | BOOT |
| GPIO 21 | RGB LED (Waveshare Zero) |
| GPIO 19 / 20 | USB D- / D+ (not on headers) |
| TX / RX | UART0 on GPIO 43 / 44 |
- 5V / 3V3 / GND
- Power
- GPIO 0
- BOOT
- GPIO 21
- RGB LED (Waveshare Zero)
- GPIO 19 / 20
- USB D- / D+ (not on headers)
- TX / RX
- UART0 on GPIO 43 / 44
Wiring the ESP32-S3 Zero and Mini board
Pick any free GPIO for I2C and pass them to Wire.begin(sda, scl). Check the pin map for your exact board; layouts differ by maker.
| ESP32-S3 Zero and Mini board pin | I2C sensor | Mini board |
|---|---|---|
| VCC | 3V3 | 3V3 |
| GND | GND | GND |
| SDA | GPIO 1 (any) | GPIO 8 (any) |
| SCL | GPIO 2 (any) | GPIO 9 (any) |
- VCC
- I2C sensor:
- 3V3
- Mini board:
- 3V3
- GND
- I2C sensor:
- GND
- Mini board:
- GND
- SDA
- I2C sensor:
- GPIO 1 (any)
- Mini board:
- GPIO 8 (any)
- SCL
- I2C sensor:
- GPIO 2 (any)
- Mini board:
- GPIO 9 (any)
Example code
Board: ESP32S3 Dev Module, Flash 4MB, PSRAM: QSPI PSRAM for S3FH4R2, USB CDC On Boot: Enabled. Change RGB_PIN for your board.
#define RGB_PIN 21 // Waveshare ESP32-S3-Zero
void setup() { Serial.begin(115200); }
void loop() {
neopixelWrite(RGB_PIN, 40, 0, 0); delay(400); // red
neopixelWrite(RGB_PIN, 0, 40, 0); delay(400); // green
neopixelWrite(RGB_PIN, 0, 0, 40); delay(400); // blue
Serial.println("tick");
}Setup and tuning
hold BOOT while connecting USB to recover.
QSPI for S3FH4R2 boards, OPI for N8R8 boards.
solder castellated boards flat, or use pin headers on a breadboard.
only boards with a charger (such as TinyS3) take a Li-Po directly.
What you need
Shop this list15 of 15 found in our store · ₹8,91,438
Waveshare ESP32-S3-Zero-N8R8 Mini Development Board, ESP32-S3 Dual-Core, 8MB Flash/PSRAM: the part this guide coversWaveshare ESP32-S3-Zero-N8R8 Mini Development Board, ESP32-S3 Dual-Core, 8MB Flash/PSRAM₹969
Waveshare ESP32-S3 Mini Dev Board w/ 8MB Flash & 8MB PSRAM: another version this guide coversWaveshare ESP32-S3 Mini Dev Board w/ 8MB Flash & 8MB PSRAM₹849
Waveshare ESP32-S3 Mini Dev Board w/ ESP32-S3-PICO-1-N8R8, 8MB Flash & PSRAM: another version this guide coversWaveshare ESP32-S3 Mini Dev Board w/ ESP32-S3-PICO-1-N8R8, 8MB Flash & PSRAM₹929
Waveshare ESP32-S3 Mini Development Board w/ ESP32-S3FH4R2: another version this guide coversWaveshare ESP32-S3 Mini Development Board w/ ESP32-S3FH4R2₹759
Waveshare ESP32-S3 Mini Development Board w/ ESP32-S3FH4R2 4MB Flash 2MB PSRAM: another version this guide coversWaveshare ESP32-S3 Mini Development Board w/ ESP32-S3FH4R2 4MB Flash 2MB PSRAM₹719
Waveshare ESP32-S3 Mini Development Board w/ ESP32-S3FH4R2, 240MHz, Wi-Fi & BLE 5: another version this guide coversWaveshare ESP32-S3 Mini Development Board w/ ESP32-S3FH4R2, 240MHz, Wi-Fi & BLE 5₹609
WeAct Studio ESP32-S3FH4R2 Mini IoT Board w/ 4MB Flash 2MB PSRAM: another version this guide coversWeAct Studio ESP32-S3FH4R2 Mini IoT Board w/ 4MB Flash 2MB PSRAM₹709
Waveshare ESP32-S3-Nano Development Board w/o Headers: another version this guide coversWaveshare ESP32-S3-Nano Development Board w/o Headers₹1,129
Unexpected Maker TinyS3 ESP32-S3 Dev Board: another version this guide coversUnexpected Maker TinyS3 ESP32-S3 Dev Board₹1,579
Adafruit QT Py S3 ESP32-S3 WiFi Dev Board w/ 2MB PSRAM & STEMMA QT: another version this guide coversAdafruit QT Py S3 ESP32-S3 WiFi Dev Board w/ 2MB PSRAM & STEMMA QT₹2,519
USB Type-C cable 1 m: a data cable for programming (not charge-only)24-Core USB Type-C Cable, 1 m₹500Closest match, check the specs
Solderless breadboard: to build without solderingSolderless Breadboard₹68
Dupont jumper wires: for the connectionsDupont Jumper Wires (40 pcs)₹49Closest match, check the specs
0.96 inch OLED display 128x64: to show readings without a computer0.96" OLED Display 128x64₹139Closest match, check the specs
18650 Li-ion cell: for battery boards with a charger18650 Li-ion Cell, More Capacities₹88Closest match, check the specs
Alternatives and when to choose them
- ESP32-S3 DevKitC: full-size board with more pins.
- ESP32-C3 boards: cheaper single-core mini boards.
- Seeed XIAO boards: another tiny family.
Common mistakes to avoid
- Wrong PSRAM mode for the S3FH4R2.
- Forgetting USB CDC On Boot, so Serial shows nothing.
- Copying the RGB pin from another maker's board.
- Powering 5 V sensors from the 3V3 pin at high current.
Frequently asked questions
Can it use Wi-Fi and BLE?
Yes, the full ESP32-S3 radio.
How much PSRAM?
2 MB on S3FH4R2 boards, 8 MB on N8R8 versions.
Can it act as a USB keyboard?
Yes, with the USBHIDKeyboard library.
Does it have a battery charger?
The Waveshare Zero does not; TinyS3 and some others do.
Why does Windows not see it?
Use a data cable, and hold BOOT while plugging in if the sketch disabled USB.
Parts for this guide
Keep learning
Sources
Written by the Geekobot team from manufacturer datasheets. Always check the datasheet for the exact part and variant you buy.

