Component guide · Beginner · 6 min read
ESP32-C3 Boards

SuperMini, DevKit and XIAO Pinout and Setup
By Geekobot Learning Team · Updated 29 Oct 2026
On this page
The ESP32-C3 is a low-cost single-core 160 MHz RISC-V chip with Wi-Fi 4 and Bluetooth 5 LE. Boards such as the C3 SuperMini, XIAO ESP32C3 and Espressif DevKitM are tiny and cheap, upload over native USB with no serial chip, and run the same Arduino and ESP-IDF code as other ESP32s. It has fewer pins than the classic ESP32 and no Classic Bluetooth.
Key specs at a glance
- CPU
- 32-bit RISC-V, single core, 160 MHz
- Memory
- 400 KB SRAM, 4 MB flash on most boards
- Wireless
- Wi-Fi 802.11 b/g/n 2.4 GHz, Bluetooth 5 LE (no Classic BT)
- GPIO
- Up to 22 (about 11 to 13 on SuperMini and XIAO boards)
- ADC
- 12-bit, 6 channels (ADC1 on GPIO 0 to 4 is the reliable one)
- USB
- Native USB serial and JTAG on GPIO 18 and 19
- Logic level
- 3.3 V only, pins are not 5 V tolerant
- Deep sleep
- About 5 uA on the chip (board LEDs and regulator add more)
Models in this guide
These are alternatives. Pick the one that fits your project; you only need one.
Option 1ESP32-C3 SuperMini Development Board w/ WiFi & Bluetooth 5.0₹269
Option 2ESP32-C3 PRO MINI WiFi & Bluetooth Development Board w/ Unsoldered Headers₹329
Option 3Elecrow ESP32-C3 Mini Development Board w/ Wi-Fi & Bluetooth 5₹549
Option 4Espressif ESP32-C3-DevKitC-02 Development Board₹799
Option 5Espressif ESP32-C3-DevKitM-1-N4X Development Board₹1,143
Option 6Waveshare ESP32-C3 Mini Development Board w/ ESP32-C3FH4 RISC-V₹529
What the ESP32-C3 is
Espressif made the C3 as a cheaper, lower-power replacement for the ESP8266, with ESP32 security features (secure boot, flash encryption) and a RISC-V core. Most dev boards here are either bare modules (ESP32-C3-MINI-1, WROOM-02) for your own PCB, or small boards with USB-C, a 3.3 V regulator, a BOOT button and an LED.
The C3 SuperMini and XIAO ESP32C3 are the smallest; the Espressif DevKitM-1 and DevKitC-02 break out every pin; the DevKit-RUST boards add an IMU and temperature sensor for learning embedded Rust.
ESP32-C3 pinout
The pins on the ESP32-C3 and what each one does.
| Pin | Function |
|---|---|
| GPIO 0 to 4 | ADC1 inputs, also general I/O |
| GPIO 2, 8, 9 | Strapping pins: leave GPIO 9 (BOOT) high at reset; 8 is the LED on many boards |
| GPIO 18, 19 | Native USB D- and D+ (used for upload and Serial) |
| GPIO 20, 21 | UART0 RX and TX |
| Any free GPIO | I2C, SPI, PWM and UART can be mapped to almost any pin |
| 5V / VBUS | USB 5 V in or out |
| 3V3 | 3.3 V from the on-board regulator |
| EN / RST | Reset (pull low to reset) |
- GPIO 0 to 4
- ADC1 inputs, also general I/O
- GPIO 2, 8, 9
- Strapping pins: leave GPIO 9 (BOOT) high at reset; 8 is the LED on many boards
- GPIO 18, 19
- Native USB D- and D+ (used for upload and Serial)
- GPIO 20, 21
- UART0 RX and TX
- Any free GPIO
- I2C, SPI, PWM and UART can be mapped to almost any pin
- 5V / VBUS
- USB 5 V in or out
- 3V3
- 3.3 V from the on-board regulator
- EN / RST
- Reset (pull low to reset)
Wiring the ESP32-C3
Pin labels differ between boards, so check the silkscreen of your board. On the SuperMini, GPIO 8 and 9 are also the LED and BOOT pins: they work for I2C, but keep anything that pulls GPIO 9 low at power-up off it. Feed 5 V into 5V/VBUS only, never into a GPIO.
| ESP32-C3 pin | C3 SuperMini | XIAO ESP32C3 |
|---|---|---|
| I2C SDA (sensor or OLED) | GPIO 8 | D4 (GPIO 6) |
| I2C SCL | GPIO 9 | D5 (GPIO 7) |
| LED or relay input | GPIO 3 | D1 (GPIO 3) |
| Analog sensor | GPIO 0 to 4 (ADC1) | A0 to A2 (GPIO 2 to 4) |
| Sensor VCC / GND | 3V3 / GND | 3V3 / GND |
- I2C SDA (sensor or OLED)
- C3 SuperMini:
- GPIO 8
- XIAO ESP32C3:
- D4 (GPIO 6)
- I2C SCL
- C3 SuperMini:
- GPIO 9
- XIAO ESP32C3:
- D5 (GPIO 7)
- LED or relay input
- C3 SuperMini:
- GPIO 3
- XIAO ESP32C3:
- D1 (GPIO 3)
- Analog sensor
- C3 SuperMini:
- GPIO 0 to 4 (ADC1)
- XIAO ESP32C3:
- A0 to A2 (GPIO 2 to 4)
- Sensor VCC / GND
- C3 SuperMini:
- 3V3 / GND
- XIAO ESP32C3:
- 3V3 / GND
Example code
In Arduino IDE pick your board (for example "ESP32C3 Dev Module" or "XIAO_ESP32C3") and set USB CDC On Boot to Enabled, or Serial prints go nowhere. The LED pin differs: 8 on SuperMini, none on XIAO, so change LED for your board.
#include <WiFi.h>
#include <WebServer.h>
const char* SSID = "your-wifi";
const char* PASS = "your-password";
const int LED = 8; // on-board LED on most C3 SuperMini boards (active LOW)
WebServer server(80);
void page() {
server.send(200, "text/html",
"<h1>LED</h1><a href='/on'>On</a> | <a href='/off'>Off</a>");
}
void setup() {
Serial.begin(115200);
pinMode(LED, OUTPUT);
WiFi.begin(SSID, PASS);
while (WiFi.status() != WL_CONNECTED) { delay(300); Serial.print("."); }
Serial.println(WiFi.localIP());
server.on("/", page);
server.on("/on", [] { digitalWrite(LED, LOW); page(); });
server.on("/off", [] { digitalWrite(LED, HIGH); page(); });
server.begin();
}
void loop() { server.handleClient(); }Setup and tuning
install "esp32 by Espressif Systems" version 2.0.5 or newer in Arduino IDE Boards Manager.
set it to Enabled on boards without a USB-serial chip so Serial Monitor works.
hold BOOT, tap RESET, release BOOT, then upload. Press RESET after upload.
a MINI-1 or WROOM-02 needs a 3.3 V supply of at least 500 mA, EN pulled high with 10 k and 1 uF, and GPIO 9 high at boot.
the tiny ceramic antenna has short range; keep metal and hands away from it.
What you need
Shop this list19 of 19 found in our store · ₹11,881
ESP32-C3 SuperMini Development Board w/ WiFi & Bluetooth 5.0: the part this guide coversESP32-C3 SuperMini Development Board w/ WiFi & Bluetooth 5.0₹269
ESP32-C3 PRO MINI WiFi & Bluetooth Development Board w/ Unsoldered Headers: another version this guide coversESP32-C3 PRO MINI WiFi & Bluetooth Development Board w/ Unsoldered Headers₹329
Elecrow ESP32-C3 Mini Development Board w/ Wi-Fi & Bluetooth 5: another version this guide coversElecrow ESP32-C3 Mini Development Board w/ Wi-Fi & Bluetooth 5₹549
Espressif ESP32-C3-DevKitC-02 Development Board: another version this guide coversEspressif ESP32-C3-DevKitC-02 Development Board₹799
Espressif ESP32-C3-DevKitM-1-N4X Development Board: another version this guide coversEspressif ESP32-C3-DevKitM-1-N4X Development Board₹1,143
Waveshare ESP32-C3 Mini Development Board w/ ESP32-C3FH4 RISC-V: another version this guide coversWaveshare ESP32-C3 Mini Development Board w/ ESP32-C3FH4 RISC-V₹529
WeAct Studio ESP32-C3FH4 WiFi Bluetooth RISC-V Dev Board: another version this guide coversWeAct Studio ESP32-C3FH4 WiFi Bluetooth RISC-V Dev Board₹429
µEDesign µEC3 ESP32-C3 WROOM-02 Dev Board w/ Wi-Fi & BLE: another version this guide coversµEDesign µEC3 ESP32-C3 WROOM-02 Dev Board w/ Wi-Fi & BLE₹515
Seeed Studio XIAO ESP32C3: another version this guide coversSeeed Studio XIAO ESP32C3₹745
DFRobot Beetle ESP32-C3 RISC-V Dev Board w/ Expansion: another version this guide coversDFRobot Beetle ESP32-C3 RISC-V Dev Board w/ Expansion₹1,009
Espressif ESP32-C3-MINI-1-H4 Wi-Fi & BLE Module w/ PCB Antenna: another version this guide coversEspressif ESP32-C3-MINI-1-H4 Wi-Fi & BLE Module w/ PCB Antenna₹249
Espressif ESP32-C3-WROOM-02-N4 Wi-Fi & BLE Module w/ PCB Antenna: another version this guide coversEspressif ESP32-C3-WROOM-02-N4 Wi-Fi & BLE Module w/ PCB Antenna₹269
Espressif ESP32-C3-DevKit-RUST-1 Development Board w/ IMU & Sensors: another version this guide coversEspressif ESP32-C3-DevKit-RUST-1 Development Board w/ IMU & Sensors₹1,929
Espressif ESP32-C3-DevKit-RUST-2 Development Board: another version this guide coversEspressif ESP32-C3-DevKit-RUST-2 Development Board₹2,665
0.96 inch OLED display 128x64: to show readings without a computer0.96" OLED Display 128x64₹139Closest match, check the specs
Solderless breadboard: to build without solderingSolderless Breadboard₹68
Dupont jumper wires: for the connectionsDupont Jumper Wires (40 pcs)₹49Closest match, check the specs
4-channel logic level converter (BSS138): to connect 5 V and 3.3 V signals safely4-Channel Logic Level Converter (BSS138)₹20
Digital multimeter: to check supply and signal voltagesDigital Multimeter₹177
Alternatives and when to choose them
- ESP32-S3, C3 and C6 compared: which chip fits which job.
- ESP32: the classic dual-core chip with Classic Bluetooth and more pins.
- Seeed XIAO boards: the XIAO family in one place.
- ESP32-C6 boards: Wi-Fi 6, Zigbee and Thread.
Common mistakes to avoid
- Leaving USB CDC On Boot disabled and seeing nothing in Serial Monitor.
- Pulling GPIO 9 low at power-up so the board starts in download mode.
- Using ADC2 (GPIO 5) while Wi-Fi is on.
- Connecting 5 V sensor outputs straight to a GPIO.
- Expecting Classic Bluetooth audio or serial: the C3 has BLE only.
Frequently asked questions
Is the ESP32-C3 compatible with ESP32 code?
Mostly yes. Wi-Fi, BLE, WebServer and most libraries work; code that uses Classic Bluetooth, DAC or touch pins does not.
Why does my C3 SuperMini not show a COM port?
Use a data USB cable, then hold BOOT while plugging in. It appears as a USB JTAG/serial device.
Which pins are I2C on the C3?
Any pins. Common defaults are GPIO 8 and 9 on SuperMini boards and GPIO 6 and 7 on the XIAO; set them with Wire.begin(SDA, SCL).
Can it run on a battery?
Yes. In deep sleep the chip uses about 5 uA, but board LEDs and regulators often draw more; the XIAO has a battery charger built in.
ESP32-C3 or ESP8266?
Choose the C3 for new designs: BLE, better security, native USB and a current Arduino core at a similar price.
Parts for this guide
Keep learning
Sources
- Espressif ESP32-C3 datasheet and technical reference manual
- Espressif Arduino-ESP32 core documentation
Written by the Geekobot team from manufacturer datasheets. Always check the datasheet for the exact part and variant you buy.
