Component guide · Intermediate · 6 min read
ESP32-C6 Boards

Wi-Fi 6, Zigbee and Thread Pinout and Setup
By Geekobot Learning Team · Updated 29 Oct 2026
On this page
The ESP32-C6 is a 160 MHz RISC-V chip with Wi-Fi 6, Bluetooth 5 LE and an 802.15.4 radio for Zigbee and Thread, plus a second low-power core. It is the ESP32 to choose for Matter, Zigbee sensors and smart-home devices. Boards range from bare MINI-1 and WROOM-1 modules to the Espressif DevKitC-1, XIAO ESP32C6, Beetle C6 and Waveshare and WeAct mini boards.
Key specs at a glance
- CPU
- RISC-V 160 MHz high-power core plus 20 MHz low-power core
- Memory
- 512 KB SRAM, 4 or 8 MB flash
- Wireless
- Wi-Fi 6 (802.11ax) 2.4 GHz, Bluetooth 5 LE, IEEE 802.15.4 (Zigbee 3.0, Thread)
- GPIO
- Up to 30 on the chip, about 11 to 23 on boards
- ADC
- 12-bit, 7 channels
- USB
- Native USB serial and JTAG on GPIO 12 and 13
- Logic level
- 3.3 V only
- Deep sleep
- About 7 uA on the chip
Models in this guide
These are alternatives. Pick the one that fits your project; you only need one.
Option 1Espressif ESP32-C6-DevKitC-1-N8 Wi-Fi 6 & BLE Dev Board₹1,209
Option 2Espressif ESP32-C6-DevKitM-1-N4 Dev Board₹1,093
Option 3Espressif ESP32-C6-MINI-1-N4 Wi-Fi 6 + Bluetooth 5 + IEEE 802.15.4 Module₹309
Option 4Espressif ESP32-C6-WROOM-1-N8 Wi-Fi 6 & BLE 5.0 Module₹409
Option 5Adafruit ESP32-C6 Feather – STEMMA QT Wi-Fi 6 & BLE 5 IoT Dev Board₹1,849
Option 6DFRobot Beetle ESP32-C6 Mini Development Board w/ BLE, Wi-Fi 6, Zigbee₹629
What the ESP32-C6 is
Wi-Fi 6 on the C6 brings Target Wake Time, so a battery device can stay connected while sleeping most of the time. The 802.15.4 radio lets the same chip be a Zigbee end device, router or coordinator, or a Thread node for Matter.
Use the DevKitC-1 or DevKitM-1 for full pin access, the XIAO, Beetle, NanoC6 or TinyC6 for small builds, the FireBeetle 2 C6 for solar and battery projects, and the Waveshare Type B board when you need a 5 to 36 V supply input.
ESP32-C6 pinout
The pins on the ESP32-C6 and what each one does.
| Pin | Function |
|---|---|
| GPIO 0 to 6 | ADC inputs and general I/O |
| GPIO 8, 9, 15 | Strapping pins: keep GPIO 9 (BOOT) high at reset |
| GPIO 12, 13 | Native USB D- and D+ |
| GPIO 16, 17 | UART0 TX and RX |
| LP GPIO 0 to 7 | Pins the low-power core can use in sleep |
| Any free GPIO | I2C, SPI, PWM and UART can be mapped freely |
| 5V / 3V3 / GND | USB 5 V, 3.3 V regulator output, ground |
| RGB LED | GPIO 8 on DevKitC-1 and many mini boards (WS2812) |
- GPIO 0 to 6
- ADC inputs and general I/O
- GPIO 8, 9, 15
- Strapping pins: keep GPIO 9 (BOOT) high at reset
- GPIO 12, 13
- Native USB D- and D+
- GPIO 16, 17
- UART0 TX and RX
- LP GPIO 0 to 7
- Pins the low-power core can use in sleep
- Any free GPIO
- I2C, SPI, PWM and UART can be mapped freely
- 5V / 3V3 / GND
- USB 5 V, 3.3 V regulator output, ground
- RGB LED
- GPIO 8 on DevKitC-1 and many mini boards (WS2812)
Wiring the ESP32-C6
Pin names change between boards, so follow the silkscreen of your board. All signals are 3.3 V; use a level shifter for 5 V modules. The XIAO ESP32C6 has an RF switch for its internal or external antenna, set by GPIO 3 and GPIO 14.
| ESP32-C6 pin | DevKitC-1 | XIAO ESP32C6 |
|---|---|---|
| I2C SDA | GPIO 6 | D4 (GPIO 22) |
| I2C SCL | GPIO 7 | D5 (GPIO 23) |
| Relay or LED | GPIO 4 | D2 (GPIO 2) |
| Analog sensor | GPIO 0 to 5 | A0 to A2 (GPIO 0 to 2) |
| Sensor VCC / GND | 3V3 / GND | 3V3 / GND |
- I2C SDA
- DevKitC-1:
- GPIO 6
- XIAO ESP32C6:
- D4 (GPIO 22)
- I2C SCL
- DevKitC-1:
- GPIO 7
- XIAO ESP32C6:
- D5 (GPIO 23)
- Relay or LED
- DevKitC-1:
- GPIO 4
- XIAO ESP32C6:
- D2 (GPIO 2)
- Analog sensor
- DevKitC-1:
- GPIO 0 to 5
- XIAO ESP32C6:
- A0 to A2 (GPIO 0 to 2)
- Sensor VCC / GND
- DevKitC-1:
- 3V3 / GND
- XIAO ESP32C6:
- 3V3 / GND
Example code
Needs the Espressif Arduino core 3.0 or newer, which added the C6. For Zigbee, open File > Examples > Zigbee, set Tools > Zigbee mode to End device (or Coordinator) and the matching partition scheme.
#include <WiFi.h>
const char* SSID = "your-wifi";
const char* PASS = "your-password";
void setup() {
Serial.begin(115200);
WiFi.begin(SSID, PASS);
while (WiFi.status() != WL_CONNECTED) { delay(300); Serial.print("."); }
Serial.print("\nIP: "); Serial.println(WiFi.localIP());
Serial.print("RSSI: "); Serial.println(WiFi.RSSI());
}
void loop() {
rgbLedWrite(RGB_BUILTIN, 0, 40, 0); // green (core 3.x)
delay(500);
rgbLedWrite(RGB_BUILTIN, 0, 0, 0);
delay(500);
}Setup and tuning
"esp32 by Espressif Systems" 3.0 or newer; choose "ESP32C6 Dev Module" or your board.
Enabled on boards without a USB-serial chip.
use the Zigbee examples in the Arduino core, or ESP-IDF with esp-zigbee-sdk or OpenThread. Matter needs ESP-IDF with esp-matter.
a C6 Zigbee end device pairs with ZHA or Zigbee2MQTT; over Wi-Fi it can use MQTT or ESPHome.
Wi-Fi 6 peaks near 350 mA, so supply at least 500 mA at 3.3 V on bare modules.
What you need
Shop this list20 of 20 found in our store · ₹16,243
Espressif ESP32-C6-DevKitC-1-N8 Wi-Fi 6 & BLE Dev Board: the part this guide coversEspressif ESP32-C6-DevKitC-1-N8 Wi-Fi 6 & BLE Dev Board₹1,209
Espressif ESP32-C6-DevKitM-1-N4 Dev Board: another version this guide coversEspressif ESP32-C6-DevKitM-1-N4 Dev Board₹1,093
Espressif ESP32-C6-MINI-1-N4 Wi-Fi 6 + Bluetooth 5 + IEEE 802.15.4 Module: another version this guide coversEspressif ESP32-C6-MINI-1-N4 Wi-Fi 6 + Bluetooth 5 + IEEE 802.15.4 Module₹309
Espressif ESP32-C6-WROOM-1-N8 Wi-Fi 6 & BLE 5.0 Module: another version this guide coversEspressif ESP32-C6-WROOM-1-N8 Wi-Fi 6 & BLE 5.0 Module₹409
Adafruit ESP32-C6 Feather – STEMMA QT Wi-Fi 6 & BLE 5 IoT Dev Board: another version this guide coversAdafruit ESP32-C6 Feather – STEMMA QT Wi-Fi 6 & BLE 5 IoT Dev Board₹1,849
DFRobot Beetle ESP32-C6 Mini Development Board w/ BLE, Wi-Fi 6, Zigbee: another version this guide coversDFRobot Beetle ESP32-C6 Mini Development Board w/ BLE, Wi-Fi 6, Zigbee₹629
DFRobot FireBeetle 2 ESP32-C6 IoT Dev Board (Wi-Fi 6, BLE 5, Solar): another version this guide coversDFRobot FireBeetle 2 ESP32-C6 IoT Dev Board (Wi-Fi 6, BLE 5, Solar)₹839
LilyGO T7-C6 ESP32-C6 Wi-Fi 6 & BLE 5 Dev Board: another version this guide coversLilyGO T7-C6 ESP32-C6 Wi-Fi 6 & BLE 5 Dev Board₹1,059
M5Stack NanoC6 Dev Kit ESP32-C6 Wi-Fi 6 Zigbee Thread Matter: another version this guide coversM5Stack NanoC6 Dev Kit ESP32-C6 Wi-Fi 6 Zigbee Thread Matter₹979
Seeed Studio Studio XIAO ESP32C6 MCU (Wi-Fi 6, BLE 5.0, Zigbee, Thread): another version this guide coversSeeed Studio XIAO ESP32C6 MCU (Wi-Fi 6, BLE 5.0, Zigbee, Thread)₹759
Unexpected Maker TinyC6 ESP32-C6 Dev Board w/ Onboard Antenna: another version this guide coversUnexpected Maker TinyC6 ESP32-C6 Dev Board w/ Onboard Antenna₹1,319
Waveshare ESP32-C6 Dev Board w/ WiFi 6, BLE 5, Zigbee & Thread: another version this guide coversWaveshare ESP32-C6 Dev Board w/ WiFi 6, BLE 5, Zigbee & Thread₹899
Waveshare ESP32-C6 Development Board, WiFi 6 & BLE, 160MHz RISC-V: another version this guide coversWaveshare ESP32-C6 Development Board, WiFi 6 & BLE, 160MHz RISC-V₹889
Waveshare ESP32-C6 Mini Development Board w/ ESP32-C6FH4, WiFi 6 & BLE 5: another version this guide coversWaveshare ESP32-C6 Mini Development Board w/ ESP32-C6FH4, WiFi 6 & BLE 5₹619
Waveshare ESP32-C6 Mini Wi-Fi 6 Development Board Type B, 5-36V Wide Voltage: another version this guide coversWaveshare ESP32-C6 Mini Wi-Fi 6 Development Board Type B, 5-36V Wide Voltage₹769
Waveshare ESP32-C6-WROOM-1-N8 WiFi 6 & Bluetooth 5 Dev Board: another version this guide coversWaveshare ESP32-C6-WROOM-1-N8 WiFi 6 & Bluetooth 5 Dev Board₹939
WeAct Studio ESP32-C6-A-N4 Dev Board ESP32C6 RISC-V WiFi6 BLE Zigbee: another version this guide coversWeAct Studio ESP32-C6-A-N4 Dev Board ESP32C6 RISC-V WiFi6 BLE Zigbee₹969
WeAct Studio ESP32-C6-MiNi Dev Board ESP32C6 RISC-V WiFi6 BLE Zigbee: another version this guide coversWeAct Studio ESP32-C6-MiNi Dev Board ESP32C6 RISC-V WiFi6 BLE Zigbee₹499
0.96 inch OLED display 128x64: to show readings without a computer0.96" OLED Display 128x64₹139Closest match, check the specs
Solderless breadboard: to build without solderingSolderless Breadboard₹68
Alternatives and when to choose them
- ESP32-S3, C3 and C6 compared: choose the right chip.
- ESP32-C3 boards: cheaper, Wi-Fi 4 and BLE only.
- Zigbee and XBee: how Zigbee networks work.
- MQTT and Home Assistant: send C6 readings to a dashboard.
Common mistakes to avoid
- Using an Arduino core older than 3.0, where the C6 is missing.
- Expecting Zigbee and Wi-Fi at full speed together: they share one radio.
- Using GPIO 12 and 13 for I/O and losing USB upload.
- Forgetting the Zigbee partition scheme and getting a boot loop.
- Powering a bare module from a weak 3.3 V regulator.
Frequently asked questions
Does the ESP32-C6 support Matter?
Yes, over Wi-Fi or Thread, using Espressif's esp-matter SDK on ESP-IDF.
Can the C6 be a Zigbee coordinator?
Yes. The Arduino core has coordinator and end-device examples; for a home network most people use it as an end device or router.
Is Wi-Fi 6 needed on my router?
No. The C6 also connects to Wi-Fi 4 and 5 routers; Wi-Fi 6 features such as Target Wake Time only work with a Wi-Fi 6 router.
C6 or C3?
Choose the C6 for Zigbee, Thread, Matter or Wi-Fi 6 power saving; the C3 is cheaper for plain Wi-Fi and BLE.
Does it have Classic Bluetooth?
No, only Bluetooth 5 LE.
Parts for this guide
Keep learning
Sources
Written by the Geekobot team from manufacturer datasheets. Always check the datasheet for the exact part and variant you buy.



