Component guide · Intermediate · 4 min read
ESP32-WROVER Module and DevKitC Board

PSRAM, Pins and Camera Use
By Geekobot Learning Team · Updated 29 Oct 2026
On this page
The ESP32-WROVER is the ESP32 module with extra PSRAM (external RAM), usually 8 MB, next to the flash. That memory makes room for camera frames, large web pages, audio buffers and LVGL screens. It runs the same code as a WROOM board, but you must enable PSRAM in the board settings, and GPIO 16 and 17 are used by the PSRAM so they are not free.
Key specs at a glance
- Chip
- ESP32-D0WD(-V3), dual-core 240 MHz
- PSRAM
- 4 or 8 MB (sometimes listed as 32 or 64 Mbit)
- Flash
- 4, 8 or 16 MB
- Antenna
- PCB (WROVER, -E) or IPEX (-I, -IE, IPEX)
- Size
- 18 x 31.4 mm
- Boards
- ESP32-DevKitC V4 with WROVER, CH340 core boards
Models in this guide
These are alternatives. Pick the one that fits your project; you only need one.
Option 1ESP32-WROVER-E ESP32-DEVKITC V4 Development Board₹1,739
Option 2ESP32-WROVER-E ESP32-DEVKITC Core Board w/ CH340₹737
Option 3ESP32 WROVER-E CH340 ESP32-DEVKITC Core Board₹1,659
Option 4ESP32-WROVER-B Development Board w/ PSRAM & RGB LED₹749
Option 5Espressif ESP32-WROVER-IE ESP32-DEVKITC Development Board₹2,259
Option 6ESP32-WROVER Module 4MB Flash 32MB PSRAM Wi-Fi Bluetooth₹296
What the ESP32-WROVER module and board is
Listings often give PSRAM in megabits: 32 Mbit is 4 MB and 64 Mbit is 8 MB. The ESP32 can map up to 4 MB directly; the rest is reachable through bank switching in ESP-IDF.
ESP32-CAM style projects, TFT dashboards and audio players are where WROVER helps. If you do not need the RAM, a WROOM board leaves two more pins free.
ESP32-WROVER module and board pinout
The pins on the ESP32-WROVER module and board and what each one does.
| Pin | Function |
|---|---|
| GPIO 16 / 17 | Used by PSRAM, not available |
| GPIO 21 / 22 | I2C |
| GPIO 18, 19, 23, 5 | SPI |
| GPIO 0 | BOOT |
| EN | Reset |
| 3V3 / 5V / GND | Power |
- GPIO 16 / 17
- Used by PSRAM, not available
- GPIO 21 / 22
- I2C
- GPIO 18, 19, 23, 5
- SPI
- GPIO 0
- BOOT
- EN
- Reset
- 3V3 / 5V / GND
- Power
Wiring the ESP32-WROVER module and board
Wiring matches a WROOM DevKit except GPIO 16 and 17. The middle column is unused here.
| ESP32-WROVER module and board pin | I2C sensor | ESP32-WROVER board |
|---|---|---|
| VCC | 5V (or 3.3V) | 3V3 |
| GND | GND | GND |
| SDA | A4 | GPIO 21 |
| SCL | A5 | GPIO 22 |
- VCC
- I2C sensor:
- 5V (or 3.3V)
- ESP32-WROVER board:
- 3V3
- GND
- I2C sensor:
- GND
- ESP32-WROVER board:
- GND
- SDA
- I2C sensor:
- A4
- ESP32-WROVER board:
- GPIO 21
- SCL
- I2C sensor:
- A5
- ESP32-WROVER board:
- GPIO 22
Example code
Select ESP32 Wrover Module (or ESP32 Dev Module with PSRAM: Enabled) in Arduino. If psramFound() is false, PSRAM is disabled in the board settings.
void setup() {
Serial.begin(115200);
delay(500);
Serial.printf("PSRAM found: %s\n", psramFound() ? "yes" : "no");
Serial.printf("PSRAM size: %u bytes\n", ESP.getPsramSize());
Serial.printf("Free PSRAM: %u bytes\n", ESP.getFreePsram());
uint8_t* buf = (uint8_t*) ps_malloc(1024 * 1024); // 1 MB in PSRAM
Serial.println(buf ? "1 MB buffer OK" : "allocation failed");
}
void loop() {}Setup and tuning
choose ESP32 Wrover Module or enable PSRAM.
frame buffers go to PSRAM automatically when it is enabled.
fit a 2.4 GHz antenna.
921600 works on most CH340 and CP2102 boards; drop to 115200 if uploads fail.
What you need
Shop this list20 of 20 found in our store · ₹12,859
ESP32-WROVER-E ESP32-DEVKITC V4 Development Board: the part this guide coversESP32-WROVER-E ESP32-DEVKITC V4 Development Board₹1,739
ESP32-WROVER-E ESP32-DEVKITC Core Board w/ CH340: another version this guide coversESP32-WROVER-E ESP32-DEVKITC Core Board w/ CH340₹737
ESP32 WROVER-E CH340 ESP32-DEVKITC Core Board: another version this guide coversESP32 WROVER-E CH340 ESP32-DEVKITC Core Board₹1,659
ESP32-WROVER-B Development Board w/ PSRAM & RGB LED: another version this guide coversESP32-WROVER-B Development Board w/ PSRAM & RGB LED₹749
Espressif ESP32-WROVER-IE ESP32-DEVKITC Development Board: another version this guide coversEspressif ESP32-WROVER-IE ESP32-DEVKITC Development Board₹2,259
ESP32-WROVER Module 4MB Flash 32MB PSRAM Wi-Fi Bluetooth: another version this guide coversESP32-WROVER Module 4MB Flash 32MB PSRAM Wi-Fi Bluetooth₹296
ESP32-WROVER WiFi Bluetooth Module 8MB Flash 64MB PSRAM: another version this guide coversESP32-WROVER WiFi Bluetooth Module 8MB Flash 64MB PSRAM₹349
ESP32-WROVER-B Module 16MB Flash 128MB PSRAM WiFi Bluetooth: another version this guide coversESP32-WROVER-B Module 16MB Flash 128MB PSRAM WiFi Bluetooth₹489
ESP32-WROVER-B WiFi Bluetooth Module 4MB Flash 32MB PSRAM: another version this guide coversESP32-WROVER-B WiFi Bluetooth Module 4MB Flash 32MB PSRAM₹359
ESP32-WROVER-B WiFi Bluetooth Module w/ 4MB Flash & 8MB PSRAM: another version this guide coversESP32-WROVER-B WiFi Bluetooth Module w/ 4MB Flash & 8MB PSRAM₹399
ESP32-WROVER-IB WiFi Bluetooth Module 16MB Flash 8MB PSRAM: another version this guide coversESP32-WROVER-IB WiFi Bluetooth Module 16MB Flash 8MB PSRAM₹481
ESP32-WROVER-IPEX WiFi Bluetooth Module 16MB Flash 128MB PSRAM: another version this guide coversESP32-WROVER-IPEX WiFi Bluetooth Module 16MB Flash 128MB PSRAM₹455
ESP32-WROVER-IPEX WiFi Bluetooth Module 8MB Flash 64MB PSRAM: another version this guide coversESP32-WROVER-IPEX WiFi Bluetooth Module 8MB Flash 64MB PSRAM₹369
ESP32-WROVER-IPEX WiFi Bluetooth Module w/ 4MB Flash & 32MB PSRAM: another version this guide coversESP32-WROVER-IPEX WiFi Bluetooth Module w/ 4MB Flash & 32MB PSRAM₹389
Espressif ESP32-WROVER-E-N4R8 Wi-Fi + Bluetooth Module: another version this guide coversEspressif ESP32-WROVER-E-N4R8 Wi-Fi + Bluetooth Module₹419
Espressif ESP32-WROVER-IE-N4R8 Wi-Fi + Bluetooth Module: another version this guide coversEspressif ESP32-WROVER-IE-N4R8 Wi-Fi + Bluetooth Module₹369
ESP32-WROVER Burn Fixture Test Board: another version this guide coversESP32-WROVER Burn Fixture Test Board₹635
USB Type-C cable 1 m: a data cable for programming (not charge-only)24-Core USB Type-C Cable, 1 m₹500Closest match, check the specs
0.96 inch OLED display 128x64: to show readings without a computer0.96" OLED Display 128x64₹139Closest match, check the specs
Solderless breadboard: to build without solderingSolderless Breadboard₹68
Alternatives and when to choose them
- ESP32 DevKit board: the WROOM version without PSRAM.
- ESP32-CAM: a WROVER-class board with a camera.
- ESP32-S3 DevKitC: newer chip with up to 16 MB octal PSRAM.
Common mistakes to avoid
- Leaving PSRAM disabled, so allocations fail.
- Using GPIO 16 and 17 for a UART or sensor.
- Confusing Mbit and MB in listings.
- Transmitting from an IPEX module without an antenna.
Frequently asked questions
WROVER or WROOM?
WROVER when you need RAM for cameras, displays or audio; WROOM otherwise.
How much PSRAM can Arduino use?
Up to 4 MB directly; 8 MB modules need ESP-IDF tricks for the rest.
Is it slower than internal RAM?
Yes, somewhat; keep time-critical data in internal RAM.
Can I use it for MicroPython?
Yes, use the SPIRAM firmware build.
What is a burn fixture?
A pogo-pin jig to flash bare modules before soldering.
Parts for this guide
Keep learning
Sources
Written by the Geekobot team from manufacturer datasheets. Always check the datasheet for the exact part and variant you buy.


