Component guide · Beginner · 3 min read
ESP32 Expansion Board (30 and 38 Pin)

Screw Terminals, Power and Pin Headers
By Geekobot Learning Team · Updated 29 Oct 2026
On this page
An ESP32 expansion board is a base that your ESP32 DevKit plugs into. It brings every pin out to screw terminals or to three-pin G-V-S headers next to a power rail, and many add a DC jack and 5 V and 3.3 V regulators. It saves breadboard space and makes servo and sensor wiring neat. Match the board to your DevKit's pin count and width.
Key specs at a glance
- Fits
- 30-pin or 38-pin ESP32 DevKit (check row spacing)
- Connections
- Screw terminals, or GPIO + VCC + GND header triples
- Power input
- DC jack 6.5 to 16 V on many, or USB on Type-C versions
- Regulators
- 5 V and 3.3 V outputs on powered versions
- Extras
- Power LED, jumper to choose 3.3 or 5 V on header rails
- FireBeetle
- DFRobot terminal board for FireBeetle 2 ESP32-E
Models in this guide
These are alternatives. Pick the one that fits your project; you only need one.
Option 1ESP32 38-Pin Expansion Board₹194
Option 2ESP32 30-Pin Expansion Board₹90
Option 3ESP32 38-Pin Expansion Board w/ Type-C Interface₹147
Option 4ESP32 Development Board 38-Pin GPIO Expansion Board w/ Type-C & Micro USB₹198
Option 530-Pin ESP32 Expansion Board w/ Type-C & Micro USB₹126
Option 6ESP32 Breakout Board 30-Pin Development Module₹239
What the ESP32 expansion board is
DevKit boards come in two widths (about 25.4 mm and 28 mm between rows) as well as two pin counts, so a 38-pin narrow board may not fit a wide base. Compare the photo and the board's row spacing before buying.
When the VCC rail is set to 5 V, servos and 5 V sensors get power, but the signal pins are still 3.3 V and must not receive 5 V outputs.
ESP32 expansion board pinout
The pins on the ESP32 expansion board and what each one does.
| Pin | Function |
|---|---|
| G / V / S triples | Ground, power rail and the GPIO signal |
| VCC jumper | Selects 3.3 V or 5 V on the V rail |
| DC jack | External supply input |
| 5V / 3V3 / GND terminals | Power outputs |
| GPIO terminals | Every ESP32 pin |
- G / V / S triples
- Ground, power rail and the GPIO signal
- VCC jumper
- Selects 3.3 V or 5 V on the V rail
- DC jack
- External supply input
- 5V / 3V3 / GND terminals
- Power outputs
- GPIO terminals
- Every ESP32 pin
Wiring the ESP32 expansion board
Do not power the board from both USB and a high-current DC supply without checking the board's diode arrangement. Servos need a supply that can deliver their stall current.
| ESP32 expansion board pin | Device | Notes |
|---|---|---|
| Servo | G-V-S header on GPIO 13 with V at 5 V | - |
| DS18B20 | Screw terminals GPIO 4, 3V3, GND with 4.7k | - |
| Power | DC jack 9 to 12 V | - |
- Servo
- Device:
- G-V-S header on GPIO 13 with V at 5 V
- Notes:
- -
- DS18B20
- Device:
- Screw terminals GPIO 4, 3V3, GND with 4.7k
- Notes:
- -
- Power
- Device:
- DC jack 9 to 12 V
- Notes:
- -
Example code
Install the ESP32Servo library. Set the V rail to 5 V for the servo and use an external supply for more than one servo.
#include <ESP32Servo.h>
Servo s;
void setup() { s.attach(13); }
void loop() {
for (int a = 0; a <= 180; a += 5) { s.write(a); delay(20); }
for (int a = 180; a >= 0; a -= 5) { s.write(a); delay(20); }
}Setup and tuning
30 vs 38 pins and narrow vs wide rows.
set the VCC jumper before connecting sensors.
pin labels follow the most common DevKit; verify against your board's silkscreen.
expansion boards often have mounting holes for a DIN carrier or box.
What you need
Shop this list13 of 13 found in our store · ₹5,024
ESP32 38-Pin Expansion Board: the part this guide coversESP32 38-Pin Expansion Board₹194
ESP32 30-Pin Expansion Board: another version this guide coversESP32 30-Pin Expansion Board₹90
ESP32 38-Pin Expansion Board w/ Type-C Interface: another version this guide coversESP32 38-Pin Expansion Board w/ Type-C Interface₹147
ESP32 Development Board 38-Pin GPIO Expansion Board w/ Type-C & Micro USB: another version this guide coversESP32 Development Board 38-Pin GPIO Expansion Board w/ Type-C & Micro USB₹198
Generic 30-Pin ESP32 Expansion Board w/ Type-C & Micro USB: another version this guide covers30-Pin ESP32 Expansion Board w/ Type-C & Micro USB₹126
Generic ESP32 Breakout Board 30-Pin Development Module: another version this guide coversESP32 Breakout Board 30-Pin Development Module₹239
Generic Black ESP32 Breakout Board for 38-Pin Development: another version this guide coversBlack ESP32 Breakout Board for 38-Pin Development₹209
ESP32-DEVKITC Development Board Backboard: another version this guide coversESP32-DEVKITC Development Board Backboard₹195
DFRobot Terminal Block Board for FireBeetle 2 ESP32-E: another version this guide coversDFRobot Terminal Block Board for FireBeetle 2 ESP32-E₹2,099
ESP32-WROOM-32 38-pin development board: a ready board with USB for comparisonESP32-WROOM-32 38-Pin Development Board₹389
USB Type-C cable 1 m: a data cable for programming (not charge-only)24-Core USB Type-C Cable, 1 m₹500Closest match, check the specs
SMPS power supply in metal enclosure (5/12/24 V): a 12 V supply for the DC jackSMPS Power Supply, Metal Enclosure (5V / 12V / 24V)₹298Closest match, check the specs
DS18B20 waterproof temperature probe: a first sensor to readSonoff DS18B20 Waterproof Temperature Sensor Probe w/ 1m Cable – 1-Wire Interface₹340Closest match, check the specs
Alternatives and when to choose them
- ESP32 DevKit board: the board that plugs in.
- ESP32 D1 R32: Uno shape for Arduino shields.
- Arduino shields: stacking add-on boards.
Common mistakes to avoid
- Buying the wrong width or pin count.
- Feeding 5 V signals back into GPIO pins.
- Running several servos from USB power.
- Leaving the VCC jumper on 5 V for 3.3 V-only sensors.
Frequently asked questions
Will my ESP32 fit?
Only if pin count and row spacing match.
Can it power servos?
Yes from the 5 V rail with an adequate DC supply.
Does it change the pinout?
No, it just brings the pins out.
Can I still use USB?
Yes, for programming and power.
What is the FireBeetle terminal board?
A screw-terminal base for DFRobot's FireBeetle 2 ESP32-E.
Parts for this guide
Projects that use it
Put this into practice: 6 step-by-step builds in our project library use parts from this guide.
Keep learning
Sources
Written by the Geekobot team from manufacturer datasheets. Always check the datasheet for the exact part and variant you buy.

