Buying guide · Beginner · 3 min read
Arduino Shields
Types, Pin Conflicts and How to Choose One
By Geekobot Learning Team · Updated 29 Oct 2026
On this page
An Arduino shield is a board that plugs onto an Uno or Mega to add a function such as motor driving, Ethernet, an LCD or easy sensor wiring. Check the shield's pin table before buying, because each shield uses fixed pins. Two shields that need the same pin cannot stack. Uno R3 shields usually fit the R4 and Mega, but check the SPI and I2C pins.
Key specs at a glance
- Form factor
- Uno R3 header layout: 14 digital + 6 analog + power pins, plus ICSP
- Logic level
- 5 V for Uno R3, Mega and most shields; R4 is 5 V with weaker pin drive
- Mega compatibility
- Header positions match, but SPI and I2C pins differ; use ICSP and SDA/SCL pins
- Common SPI pins (Uno)
- D10 (CS), D11 (MOSI), D12 (MISO), D13 (SCK)
- Common I2C pins (Uno)
- A4 (SDA), A5 (SCL)
Common shield types
These are the shields you will meet most often:
| Shield | What it does | Pins it uses (Uno) | Notes |
|---|---|---|---|
| Proto shield | Solder or breadboard your own circuit on top of the Uno | None; all pins pass through | Mini breadboard versions are handy for testing |
| Sensor shield | Breaks out every pin as 3-pin signal, 5 V, GND headers | None; passthrough | Makes connecting servos and sensors tidy |
| Motor shield | H-bridge for DC motors and steppers | D3 and D11 PWM; D12 and D13 direction; D8 and D9 brake; A0 and A1 current sense | Needs a separate motor supply |
| Ethernet shield | Wired network and microSD | D10, D11, D12, D13 (W5100/W5500 chip) and D4 (SD) | Uses SPI, so avoid other SPI devices on D10 |
| LCD keypad shield | 16x2 LCD with six buttons | D4 to D9 and A0 (buttons share one analog pin) | Fixed pins limit what else you can attach |
| CNC shield V3 | Four stepper driver sockets for GRBL | D2 to D13 and A0 to A3 | Pairs with A4988 or DRV8825 drivers on an Uno |
| Relay shield | 2 to 4 relays on board | Typically D4 to D7 | Check relay coil voltage and isolation |
- Proto shield
- What it does:
- Solder or breadboard your own circuit on top of the Uno
- Pins it uses (Uno):
- None; all pins pass through
- Notes:
- Mini breadboard versions are handy for testing
- Sensor shield
- What it does:
- Breaks out every pin as 3-pin signal, 5 V, GND headers
- Pins it uses (Uno):
- None; passthrough
- Notes:
- Makes connecting servos and sensors tidy
- Motor shield
- What it does:
- H-bridge for DC motors and steppers
- Pins it uses (Uno):
- D3 and D11 PWM; D12 and D13 direction; D8 and D9 brake; A0 and A1 current sense
- Notes:
- Needs a separate motor supply
- Ethernet shield
- What it does:
- Wired network and microSD
- Pins it uses (Uno):
- D10, D11, D12, D13 (W5100/W5500 chip) and D4 (SD)
- Notes:
- Uses SPI, so avoid other SPI devices on D10
- LCD keypad shield
- What it does:
- 16x2 LCD with six buttons
- Pins it uses (Uno):
- D4 to D9 and A0 (buttons share one analog pin)
- Notes:
- Fixed pins limit what else you can attach
- CNC shield V3
- What it does:
- Four stepper driver sockets for GRBL
- Pins it uses (Uno):
- D2 to D13 and A0 to A3
- Notes:
- Pairs with A4988 or DRV8825 drivers on an Uno
- Relay shield
- What it does:
- 2 to 4 relays on board
- Pins it uses (Uno):
- Typically D4 to D7
- Notes:
- Check relay coil voltage and isolation
Compatibility: Uno, R4, Mega and Nano
The R4 keeps the shield headers, but each pin can supply only about 8 mA, so shields that drive LEDs or logic directly from pins may need resistors or buffer chips.
Headers match the Uno, but SPI is on pins 50 to 53 and I2C is on pins 20 and 21. Good shields route SPI through the ICSP header and I2C through the SDA/SCL header so they still work.
They have no shield headers. Use a Nano IO shield or terminal adapter board instead.
Never plug a 5 V shield onto a 3.3 V board without checking level shifting.
Avoiding pin conflicts
Write down the pins each shield uses before you stack them. Two shields that both use D10 for chip select or D4 for the SD card will fight. Fixes include cutting a header leg and rerouting with a jumper, picking another shield with a different pin layout, or moving one device to a separate board connected by wires. A sensor shield or proto shield sits well at the bottom or top because it passes every pin through.
Power and heat
Motor and relay shields draw far more current than the Uno's regulator can supply. Use the shield's separate power terminal for motors, keep the jumper settings as the manual describes and share the ground. Stacked shields also tend to hide the Uno's USB and power jacks, so check you can still plug in.
Common mistakes to avoid
- Stacking two shields that both claim D10 or the SPI pins.
- Powering motors from the Uno's 5 V pin.
- Plugging an Uno shield into a Mega and expecting SPI to work.
- Forgetting that LCD keypad shields use A0 for the buttons.
- Using a 5 V shield on a 3.3 V board.
Frequently asked questions
Do Uno shields work on the Uno R4?
Mostly yes, since the headers match. Check the shield's pin current needs because R4 pins deliver less current.
Can I use an Uno shield on an ESP32?
Only boards in the Uno footprint, such as some ESP32 Uno-format boards, and only if the shield accepts 3.3 V logic.
What is the difference between a shield and a module?
A shield plugs directly onto the board's headers. A module connects with jumper wires.
Can I stack three shields?
Yes if their pin use does not overlap and the stack height still lets the headers mate.
Are shields reprogrammable?
Shields are mostly passive. Programming happens on the Uno underneath.
What is a proto shield used for?
It gives you a soldered mini-board that sits on the Uno, so a prototype can become a compact permanent build.
Parts for this guide
Terms in this guide
Projects that use it
Put this into practice: 1 step-by-step build in our project library uses parts from this guide.
Keep learning
Sources
- Arduino documentation: Uno R3, Uno R4 and Mega 2560 pin mapping
- Arduino Motor Shield Rev3 and Ethernet Shield 2 datasheets
Written by the Geekobot team from manufacturer datasheets. Always check the datasheet for the exact part and variant you buy.




