Component guide · Beginner · 3 min read
SHTC3 Humidity and Temperature Sensor

Pinout, Wiring and Code
By Geekobot Learning Team · Updated 29 Oct 2026
On this page
The Sensirion SHTC3 is a tiny, low-power digital humidity and temperature sensor on I2C at address 0x70, with ±2 % RH and ±0.2 °C accuracy. It sleeps between readings at under 1 µA, which makes it ideal for battery and coin-cell projects. Breakouts from Adafruit, SparkFun and DFRobot add a regulator and Qwiic or STEMMA QT connectors.
Key specs at a glance
- Humidity
- 0 to 100 % RH, ±2 %
- Temperature
- -40 to +125 °C, ±0.2 °C
- Interface
- I2C, fixed address 0x70
- Supply
- 1.62 to 3.6 V (breakouts 3.3 to 5 V)
- Current
- About 0.3 µA asleep, under 1 µA average at 1 reading per second
- Package
- 2 × 2 mm DFN (on breakouts for hobby use)
A shorted, over-charged or damaged lithium cell can get very hot and catch fire. Use a protection board or BMS, never short the terminals, charge on a non-flammable surface and do not leave a charging pack alone. Throw away cells that are swollen or dented.
Models in this guide
These are alternatives. Pick the one that fits your project; you only need one.
Option 1DFRobot Fermion SHTC3 Humidity & Temperature Sensor – I2C Interface₹609
Option 2Adafruit Sensirion SHTC3 Temperature & Humidity Sensor – STEMMA QT / Qwiic Breakout₹1,103
Option 3SparkFun SHTC3 Humidity Sensor Breakout (Qwiic) – I2C Digital Sensor Module₹939
Option 4Sensirion SHTC3 Digital Humidity & Temperature Sensor – I²C Interface, Ultra-Low Power₹87
Option 5Sensirion SHTC3-TR-10KS Humidity & Temperature Sensor IC, 0 to 100%RH, −40°C to +125°C, I2C Interface₹83
Option 6Sensirion SHTC3-TR-2.5KS Humidity & Temperature Sensor IC, 0 to 100%RH, −40°C to +125°C, I2C Interface₹108
What the SHTC3 sensor is
The SHTC3 was designed for phones and wearables, so it wakes, measures and goes back to sleep quickly. Its accuracy is close to the SHT31 at lower cost and power.
The bare chip is very small; buy a breakout unless you are designing a PCB. Its I2C address (0x70) is the same as the TCA9548A multiplexer, so watch for conflicts.
SHTC3 sensor pinout
The pins on the SHTC3 sensor and what each one does.
| Pin | Function |
|---|---|
| VIN / VCC | Supply (3.3 or 5 V on breakouts) |
| GND | Ground |
| SDA | I2C data |
| SCL | I2C clock |
- VIN / VCC
- Supply (3.3 or 5 V on breakouts)
- GND
- Ground
- SDA
- I2C data
- SCL
- I2C clock
Wiring the SHTC3 sensor
Most breakouts have pull-up resistors and a regulator, so they run from 3.3 V or 5 V. Bare sensor ICs are 3.3 V (or 1.8 V) only: solder them to a breakout first and use a level shifter with 5 V boards.
| SHTC3 sensor pin | Arduino Uno | ESP32 |
|---|---|---|
| VCC | 5V (or 3.3V) | 3V3 |
| GND | GND | GND |
| SDA | A4 | GPIO 21 |
| SCL | A5 | GPIO 22 |
- VCC
- Arduino Uno:
- 5V (or 3.3V)
- ESP32:
- 3V3
- GND
- Arduino Uno:
- GND
- ESP32:
- GND
- SDA
- Arduino Uno:
- A4
- ESP32:
- GPIO 21
- SCL
- Arduino Uno:
- A5
- ESP32:
- GPIO 22
Example code
The SparkFun SHTC3 library works too. The sensor sleeps automatically between readings with these libraries.
#include <Adafruit_SHTC3.h>
Adafruit_SHTC3 shtc3;
void setup() {
Serial.begin(115200);
if (!shtc3.begin()) { Serial.println("SHTC3 not found"); while (1); }
}
void loop() {
sensors_event_t hum, temp;
shtc3.getEvent(&hum, &temp); // wakes, measures, sleeps
Serial.print(temp.temperature, 2); Serial.print(" C ");
Serial.print(hum.relative_humidity, 1); Serial.println(" %RH");
delay(2000);
}Setup and tuning
read every few minutes and let the ESP32 deep-sleep in between.
keep it away from the regulator and ESP32, which warm the air around them.
0x70 is also the TCA9548A address; put the SHTC3 on a different bus if you use one.
a small hole in the case over the sensor gives faster, truer readings.
What you need
Shop this list10 of 11 found in our store · ₹4,105
DFRobot Fermion SHTC3 Humidity & Temperature Sensor – I2C Interface: the part this guide coversDFRobot Fermion SHTC3 Humidity & Temperature Sensor – I2C Interface₹609
Adafruit Sensirion SHTC3 Temperature & Humidity Sensor – STEMMA QT / Qwiic Breakout: another version this guide coversAdafruit Sensirion SHTC3 Temperature & Humidity Sensor – STEMMA QT / Qwiic Breakout₹1,103
SparkFun SHTC3 Humidity Sensor Breakout (Qwiic) – I2C Digital Sensor Module: another version this guide coversSparkFun SHTC3 Humidity Sensor Breakout (Qwiic) – I2C Digital Sensor Module₹939
Sensirion SHTC3 Digital Humidity & Temperature Sensor – I²C Interface, Ultra-Low Power: another version this guide coversSensirion SHTC3 Digital Humidity & Temperature Sensor – I²C Interface, Ultra-Low Power₹87
Sensirion SHTC3-TR-10KS Humidity & Temperature Sensor IC, 0 to 100%RH, −40°C to +125°C, I2C Interface: another version this guide coversSensirion SHTC3-TR-10KS Humidity & Temperature Sensor IC, 0 to 100%RH, −40°C to +125°C, I2C Interface₹83
Sensirion SHTC3-TR-2.5KS Humidity & Temperature Sensor IC, 0 to 100%RH, −40°C to +125°C, I2C Interface: another version this guide coversSensirion SHTC3-TR-2.5KS Humidity & Temperature Sensor IC, 0 to 100%RH, −40°C to +125°C, I2C Interface₹108
RAKwireless WisBlock Temperature and Humidity Sensor Sensirion SHTC3 RAK1901 – I2C Interface: another version this guide coversRAKwireless WisBlock Temperature and Humidity Sensor Sensirion SHTC3 RAK1901 – I2C Interface₹599
ESP32-WROOM-32 38-pin development board: for Wi-Fi logging and dashboardsESP32-WROOM-32 38-Pin Development Board₹389- Uno R3 development board: the controller used in the wiring tableFind this part
0.96 inch OLED display 128x64: to show readings without a computer0.96" OLED Display 128x64₹139Closest match, check the specs
Dupont jumper wires: for the connectionsDupont Jumper Wires (40 pcs)₹49Closest match, check the specs
Alternatives and when to choose them
- SHT3x and SHT4x sensors: the next step up in accuracy.
- AHT20 sensor: cheaper, slightly less accurate.
- SHT20 sensor: older family, common in probes.
Try it: I2c pullup calculator
Change the values and the diagram and results update as you type.
Common mistakes to avoid
- Using a TCA9548A multiplexer on the same bus (same 0x70 address).
- Mounting it next to the ESP32 or regulator so it reads warm.
- Soldering the bare DFN chip by hand without a breakout.
- Powering the bare chip from 5 V.
Frequently asked questions
What is the SHTC3 I2C address?
0x70, fixed.
Is it good for battery projects?
Yes, it draws under 1 µA on average at one reading a second.
SHTC3 or SHT31?
Similar accuracy; the SHTC3 uses less power, the SHT31 has an alert pin and two addresses.
Does it work with 5 V Arduino?
Breakouts with a regulator do; the bare chip is 3.3 V only.
Why is the temperature high?
Heat from nearby parts; move it away from the board or give it airflow.
Parts for this guide
Calculators
Projects that use it
Put this into practice: 1 step-by-step build in our project library uses parts from this guide.
Keep learning
Sources
Written by the Geekobot team from manufacturer datasheets. Always check the datasheet for the exact part and variant you buy.

