Component guide · Beginner · 4 min read
SHT20 Humidity Sensor and Probe

Pinout, Wiring and Code
By Geekobot Learning Team · Updated 29 Oct 2026
On this page
The Sensirion SHT20 is a digital humidity and temperature sensor on I2C at address 0x40, with ±3 % RH accuracy. The SHT21 (±2 %) and SHT25 (±1.8 %) are the same family with better accuracy. They are often sold inside stainless steel or filtered probes on a cable, which makes them a common choice for greenhouses, incubators and cold rooms.
Key specs at a glance
- Humidity
- 0 to 100 % RH, ±3 % (SHT20), ±2 % (SHT21), ±1.8 % (SHT25)
- Temperature
- -40 to +125 °C, about ±0.3 °C
- Interface
- I2C, fixed address 0x40
- Supply
- 2.1 to 3.6 V for the chip (probes often 3.3 to 5 V)
- Resolution
- 12-bit RH, 14-bit temperature (default)
- Probe wires
- Usually red VCC, black GND, yellow SDA, green or blue SCL (check yours)
Models in this guide
These are alternatives. Pick the one that fits your project; you only need one.
Option 1Sensirion SHT20 Humidity & Temperature Sensor, 0 to 100%RH, −40°C to +125°C, ±3%RH, I²C Interface, DFN Package₹135
Option 2Sensirion SHT21 Humidity & Temperature Sensor, 0 to 100%RH, −40 °C to +125 °C, I2C Interface₹279
Option 3Sensirion SHT25 Humidity & Temperature Sensor, 0-100%RH, −40°C to +125°C, ±1.8%RH, I2C Interface, DFN-6 Package₹779
Option 4Ascenta ASHT20/21 MEMS Temperature & Humidity Sensor – I2C Digital Output₹71
Option 5Sensirion SHT20 Digital Temperature & Humidity Probe – Stainless Steel Sensor w/ 1m Cable₹239
Option 6Renke SHT-58 Temperature Sensor Probe for SHT20, 58mm Length – Digital I2C₹1,359
What the SHT20 sensor is
The sensor measures humidity with a capacitive element and temperature with a band-gap sensor on the same chip, then sends calibrated values over I2C.
Probe versions put the chip behind a sintered filter or PTFE membrane so it can work in dusty or damp air. Long probe cables add capacitance; keep I2C cables under about 2 m or add stronger pull-ups. The RS485 transmitter versions are different products with Modbus output.
SHT20 sensor pinout
The pins on the SHT20 sensor and what each one does.
| Pin | Function |
|---|---|
| VCC | Supply (3.3 V for bare chips) |
| GND | Ground |
| SDA | I2C data |
| SCL | I2C clock |
- VCC
- Supply (3.3 V for bare chips)
- GND
- Ground
- SDA
- I2C data
- SCL
- I2C clock
Wiring the SHT20 sensor
Most breakouts have pull-up resistors and a regulator, so they run from 3.3 V or 5 V. Bare sensor ICs are 3.3 V (or 1.8 V) only: solder them to a breakout first and use a level shifter with 5 V boards. Cable probes usually have no pull-ups: add 4.7 kΩ from SDA and SCL to 3.3 V.
| SHT20 sensor pin | Arduino Uno | ESP32 |
|---|---|---|
| VCC / VIN | 3.3V (5V only if the board has a regulator) | 3V3 |
| GND | GND | GND |
| SDA | A4 (through a level shifter on bare 3.3 V boards) | GPIO 21 |
| SCL | A5 | GPIO 22 |
- VCC / VIN
- Arduino Uno:
- 3.3V (5V only if the board has a regulator)
- ESP32:
- 3V3
- GND
- Arduino Uno:
- GND
- ESP32:
- GND
- SDA
- Arduino Uno:
- A4 (through a level shifter on bare 3.3 V boards)
- ESP32:
- GPIO 21
- SCL
- Arduino Uno:
- A5
- ESP32:
- GPIO 22
Example code
This direct code works for SHT20, SHT21 and SHT25. Libraries such as DFRobot_SHT20 or uFire_SHT20 wrap the same commands.
#include <Wire.h>
float readSHT(byte cmd, bool hum) {
Wire.beginTransmission(0x40);
Wire.write(cmd); // 0xF5 = RH, 0xF3 = temperature (no hold)
Wire.endTransmission();
delay(hum ? 30 : 90);
Wire.requestFrom(0x40, 3);
uint16_t raw = (Wire.read() << 8) | Wire.read();
Wire.read(); // CRC, ignored here
raw &= 0xFFFC;
return hum ? -6.0 + 125.0 * raw / 65536.0 : -46.85 + 175.72 * raw / 65536.0;
}
void setup() { Wire.begin(); Serial.begin(115200); }
void loop() {
Serial.print(readSHT(0xF5, true), 1); Serial.print(" %RH ");
Serial.print(readSHT(0xF3, false), 1); Serial.println(" C");
delay(2000);
}Setup and tuning
add 4.7 kΩ pull-ups for bare chips and cable probes.
keep I2C under about 2 m; for longer runs use the RS485 transmitter versions.
after the sensor gets wet, readings stay high until it dries; a filter cap helps.
read every few seconds, not continuously, to avoid warming the sensor.
What you need
Shop this list15 of 16 found in our store · ₹12,057
Sensirion SHT20 Humidity & Temperature Sensor, 0 to 100%RH, −40°C to +125°C, ±3%RH, I²C Interface, DFN Package: the part this guide coversSensirion SHT20 Humidity & Temperature Sensor, 0 to 100%RH, −40°C to +125°C, ±3%RH, I²C Interface, DFN Package₹135
Sensirion SHT21 Humidity & Temperature Sensor, 0 to 100%RH, −40 °C to +125 °C, I2C Interface: another version this guide coversSensirion SHT21 Humidity & Temperature Sensor, 0 to 100%RH, −40 °C to +125 °C, I2C Interface₹279
Sensirion SHT25 Humidity & Temperature Sensor, 0-100%RH, −40°C to +125°C, ±1.8%RH, I2C Interface, DFN-6 Package: another version this guide coversSensirion SHT25 Humidity & Temperature Sensor, 0-100%RH, −40°C to +125°C, ±1.8%RH, I2C Interface, DFN-6 Package₹779
Ascenta ASHT20/21 MEMS Temperature & Humidity Sensor – I2C Digital Output: another version this guide coversAscenta ASHT20/21 MEMS Temperature & Humidity Sensor – I2C Digital Output₹71
Sensirion SHT20 Digital Temperature & Humidity Probe – Stainless Steel Sensor w/ 1m Cable: another version this guide coversSensirion SHT20 Digital Temperature & Humidity Probe – Stainless Steel Sensor w/ 1m Cable₹239
Renke SHT-58 Temperature Sensor Probe for SHT20, 58mm Length – Digital I2C: another version this guide coversRenke SHT-58 Temperature Sensor Probe for SHT20, 58mm Length – Digital I2C₹1,359
Renke SHT-68 Hard Cover Temperature & Humidity Sensor Probe (SHT20, I²C), 68mm Length: another version this guide coversRenke SHT-68 Hard Cover Temperature & Humidity Sensor Probe (SHT20, I²C), 68mm Length₹775
Renke SHT-70 PE Temperature Sensor Probe for SHT20, 70mm Length: another version this guide coversRenke SHT-70 PE Temperature Sensor Probe for SHT20, 70mm Length₹994
Renke SHT-71 Temperature & Humidity Sensor Probe for SHT20, 71mm Length – Digital I2C: another version this guide coversRenke SHT-71 Temperature & Humidity Sensor Probe for SHT20, 71mm Length – Digital I2C₹1,749
Renke SHT-77 Temperature Sensor Probe for SHT20 – 77mm Length, I2C Digital Output: another version this guide coversRenke SHT-77 Temperature Sensor Probe for SHT20 – 77mm Length, I2C Digital Output₹1,359
Renke SHT-155-LW Quarter Pipe Thread Temperature Sensor Probe for SHT20: another version this guide coversRenke SHT-155-LW Quarter Pipe Thread Temperature Sensor Probe for SHT20₹3,491- Uno R3 development board: the controller used in the wiring tableFind this part
ESP32-WROOM-32 38-pin development board: for Wi-Fi logging and dashboardsESP32-WROOM-32 38-Pin Development Board₹389
0.96 inch OLED display 128x64: to show readings without a computer0.96" OLED Display 128x64₹139Closest match, check the specs
Resistor assortment kit: for pull-up and divider resistorsResistor Assortment Kit₹250
Dupont jumper wires: for the connectionsDupont Jumper Wires (40 pcs)₹49Closest match, check the specs
Alternatives and when to choose them
- SHT3x and SHT4x sensors: newer, faster and more accurate.
- SHTC3 sensor: tiny low-power Sensirion sensor.
- HTU21D: a compatible sensor at the same 0x40 address.
Try it: I2c pullup calculator
Change the values and the diagram and results update as you type.
Common mistakes to avoid
- No pull-ups on a cable probe, so I2C reads fail.
- Running a 5 m I2C cable to a probe.
- Two sensors on one bus: the 0x40 address is fixed.
- Reading it as fast as possible, which self-heats it.
Frequently asked questions
What is the SHT20 I2C address?
0x40, and it cannot be changed.
SHT20, SHT21 or SHT25?
Same pins and code; they differ in accuracy, with the SHT25 the most accurate.
Can I use two on one Arduino?
Use an I2C multiplexer such as the TCA9548A, or two I2C buses on an ESP32.
Does it work with 5 V Arduino?
Probe and module versions with a regulator do; bare chips need 3.3 V and level shifting.
Is it waterproof?
The probes resist dust and splashes, but the sensor itself must not stay wet.
Parts for this guide
Sensirion SHT20 Humidity & Temperature Sensor, 0 to 100%RH, −40°C to +125°C, ±3%RH, I²C Interface, DFN Package₹135View- ₹279View
Sensirion SHT25 Humidity & Temperature Sensor, 0-100%RH, −40°C to +125°C, ±1.8%RH, I2C Interface, DFN-6 Package₹779View- ₹71View
- ₹239View
- ₹1,359View
- ₹775View
- ₹994View
- ₹1,749View
- ₹1,359View
- ₹3,491View
- ₹359View
- ₹389View
- ₹139View
- ₹33View
- ₹49View
Calculators
Projects that use it
Put this into practice: 1 step-by-step build in our project library uses parts from this guide.
Keep learning
Sources
Written by the Geekobot team from manufacturer datasheets. Always check the datasheet for the exact part and variant you buy.


