Component guide · Beginner · 3 min read
AHT20 / AHT10 Temperature and Humidity Sensor

Pinout, Wiring, Code
By Geekobot Learning Team · Updated 29 Oct 2026
On this page
The AHT20 is a small I2C temperature and humidity sensor with about ±2 percent RH and ±0.3 °C accuracy, a good modern replacement for the DHT11 and DHT22. It uses I2C address 0x38, runs at 2 to 5.5 V and reads in about 80 ms. The older AHT10 is similar but less tolerant of sharing the I2C bus.
Key specs at a glance
- Humidity
- 0 to 100 % RH, ±2 % typical
- Temperature
- −40 to +85 °C, ±0.3 °C typical
- Interface
- I2C, address 0x38 (fixed)
- Supply
- 2.0 to 5.5 V
- Measurement time
- About 80 ms
- Variants
- AHT10 (older), AHT20, AHT21 (better long-term stability)
Models in this guide
These are alternatives. Pick the one that fits your project; you only need one.
Option 1Asair AHT20 Temperature & Humidity Sensor -40°C to +85°C – I2C Digital Output₹56
Option 2DFRobot Gravity AHT20 Temperature Humidity Sensor – I2C Interface₹529
Option 3DFRobot Fermion AHT20 Temperature Humidity Sensor Breakout – I2C Interface₹469
Option 4AHT10 High Precision Digital Temperature & Humidity Sensor Module – I2C Interface₹84
Option 5AHT20 Digital Temperature & Humidity Probe – 1m Cable, I2C Interface, Stainless Steel₹429
What the AHT20 sensor is
The AHT20 from Aosong (Asair) combines a capacitive humidity sensor and a temperature sensor with a calibrated digital output. Unlike the DHT11 and DHT22, it uses the standard I2C bus, so it shares two wires with displays and other sensors and needs no special timing.
Probe versions put the sensor in a vented stainless shell on a cable for greenhouses, incubators and outdoor boxes.
AHT20 sensor pinout
The pins on the AHT20 sensor and what each one does.
| Pin | Function |
|---|---|
| VCC (VIN) | 2.0 to 5.5 V |
| GND | Ground |
| SCL | I2C clock |
| SDA | I2C data |
- VCC (VIN)
- 2.0 to 5.5 V
- GND
- Ground
- SCL
- I2C clock
- SDA
- I2C data
Wiring the AHT20 sensor
The address is fixed at 0x38. To use two AHT20 sensors, put them on separate I2C buses (ESP32 has two) or use an I2C multiplexer.
| AHT20 sensor pin | Arduino Uno | ESP32 |
|---|---|---|
| VCC | 5V (or 3.3V) | 3V3 |
| GND | GND | GND |
| SDA | A4 | GPIO 21 |
| SCL | A5 | GPIO 22 |
- VCC
- Arduino Uno:
- 5V (or 3.3V)
- ESP32:
- 3V3
- GND
- Arduino Uno:
- GND
- ESP32:
- GND
- SDA
- Arduino Uno:
- A4
- ESP32:
- GPIO 21
- SCL
- Arduino Uno:
- A5
- ESP32:
- GPIO 22
Example code
The Adafruit AHTX0 library supports both the AHT10 and AHT20.
#include <Adafruit_AHTX0.h>
Adafruit_AHTX0 aht;
void setup() {
Serial.begin(115200);
if (!aht.begin()) { Serial.println("AHT not found"); while (1); }
}
void loop() {
sensors_event_t hum, temp;
aht.getEvent(&hum, &temp);
Serial.printf("%.1f C %.1f %%RH\n", temp.temperature, hum.relative_humidity);
delay(2000);
}Setup and tuning
reading continuously warms the sensor slightly; one reading every 2 s or slower is plenty.
keep it away from the microcontroller, voltage regulators and direct sun. Inside a box, give it vents.
at 100 % RH water can form on the sensor; probe versions with a filter cap handle this better.
AHT20 + BMP280 modules add air pressure on the same two wires.
What you need
Shop this list7 of 7 found in our store · ₹2,095
Asair AHT20 temperature and humidity sensor: the bare sensorAsair AHT20 Temperature & Humidity Sensor -40°C to +85°C – I2C Digital Output₹56
DFRobot Gravity AHT20 sensor: Gravity connectorDFRobot Gravity AHT20 Temperature Humidity Sensor – I2C Interface₹529
DFRobot Fermion AHT20 breakout: breadboard friendlyDFRobot Fermion AHT20 Temperature Humidity Sensor Breakout – I2C Interface₹469Closest match, check the specs
AHT10 temperature and humidity module: the older AHT10 versionAHT10 High Precision Digital Temperature & Humidity Sensor Module – I2C Interface₹84Closest match, check the specs
AHT20 stainless steel probe, 1 m cable: for outdoor or damp placesAHT20 Digital Temperature & Humidity Probe – 1m Cable, I2C Interface, Stainless Steel₹429Closest match, check the specs
ESP32-WROOM-32 38-pin development board: for Wi-Fi logging and dashboardsESP32-WROOM-32 38-Pin Development Board₹389
0.96 inch OLED display 128x64: to show readings without a computer0.96" OLED Display 128x64₹139Closest match, check the specs
Alternatives and when to choose them
- DHT11 vs DHT22: single-wire sensors used in many tutorials.
- SHT3x sensors: higher accuracy and long-term stability.
- BME280: adds air pressure for weather stations.
Try it: I2c pullup calculator
Change the values and the diagram and results update as you type.
Common mistakes to avoid
- Placing the sensor next to the ESP32 or regulator, which reads several degrees high.
- Polling continuously, which causes self-heating.
- Trying to use two AHT20s on one bus.
- Sealing it in a box without vents.
Frequently asked questions
Is AHT20 better than DHT22?
Similar accuracy, but the AHT20 uses I2C, reads faster and is more reliable on long-running projects.
AHT10 or AHT20?
Choose AHT20. The AHT10 can lock the I2C bus when other devices share it.
What is its I2C address?
0x38, and it cannot be changed.
Does it work at 3.3 V?
Yes, from 2.0 to 5.5 V.
Can it be used outdoors?
Use a probe version in a vented shield, out of direct sun and rain.
How often can I read it?
Every 2 seconds or slower is ideal to avoid self-heating.
Parts for this guide
Calculators
Terms in this guide
Projects that use it
Put this into practice: 26 step-by-step builds in our project library use parts from this guide.
Keep learning
Sources
Written by the Geekobot team from manufacturer datasheets. Always check the datasheet for the exact part and variant you buy.
