Comparison · Beginner · 3 min read
BME280 vs BMP280
Temperature, Humidity and Pressure Sensors
By Geekobot Learning Team · Updated 24 Oct 2026
On this page
The BMP280 measures temperature and air pressure; the BME280 adds relative humidity. Both are Bosch sensors on I2C or SPI, at address 0x76 or 0x77, and the bare chips run at 1.71 to 3.6 V. Pressure is accurate to about ±1 hPa, enough to estimate altitude changes of about a metre. The BME680 adds a gas sensor for indoor air quality. Check the chip ID, because BMP280s are often sold as BME280s.
Key specs at a glance
- Measures
- BMP280: temperature, pressure. BME280: + humidity. BME680: + gas (VOC)
- Pressure range
- 300 to 1100 hPa
- Pressure accuracy
- About ±1 hPa absolute, ±0.12 hPa relative
- Humidity accuracy
- About ±3 % RH (BME280)
- Supply
- 1.71 to 3.6 V chip; many modules add a regulator for 5 V
- Interface
- I2C (0x76 or 0x77) or SPI
Which one do you need?
| Sensor | Temperature | Humidity | Pressure | Gas | Chip ID |
|---|---|---|---|---|---|
| BMP280 | Yes | No | Yes | No | 0x58 |
| BME280 | Yes | Yes | Yes | No | 0x60 |
| BME680 / BME688 | Yes | Yes | Yes | VOC index | 0x61 |
- BMP280
- Temperature:
- Yes
- Humidity:
- No
- Pressure:
- Yes
- Gas:
- No
- Chip ID:
- 0x58
- BME280
- Temperature:
- Yes
- Humidity:
- Yes
- Pressure:
- Yes
- Gas:
- No
- Chip ID:
- 0x60
- BME680 / BME688
- Temperature:
- Yes
- Humidity:
- Yes
- Pressure:
- Yes
- Gas:
- VOC index
- Chip ID:
- 0x61
Wiring and the 0x76 / 0x77 address
Connect VIN (or VCC) to 3.3 V, GND to GND, SDA and SCL to your board's I2C pins. Use 5 V only if the module has a regulator and level shifting; a bare 3.3 V board will be damaged. The SDO pin sets the address: to GND for 0x76, to VCC for 0x77. Many Adafruit-style libraries default to 0x77 while most low-cost modules are 0x76, so if the sensor is "not found", pass the other address to begin() or run an I2C scanner.
Accurate readings and altitude
Self-heating: in continuous mode the chip warms slightly and reads high. Use forced mode, which takes one reading then sleeps, for weather logging. Mount the sensor away from regulators and the microcontroller.
Altitude: pressure falls by about 12 Pa per metre near sea level. To get absolute altitude you must give the library today's sea-level pressure from a local weather report; for relative height changes, such as a drone or a lift, just compare readings.
Fake BME280: if the humidity reads 0 or the library reports chip ID 0x58, you have a BMP280. Compare against a DHT22 if you need a second humidity reading.
Try it: I2C pull-up calculator
Change the values and the diagram and results update as you type.
Common mistakes to avoid
- Powering a bare 3.3 V module from 5 V.
- Using the wrong I2C address (0x76 vs 0x77).
- Mounting the sensor next to a hot regulator.
- Expecting absolute altitude without setting sea-level pressure.
- Buying a cheap 'BME280' that is really a BMP280.
Frequently asked questions
What is the difference between BME280 and BMP280?
The BME280 measures humidity as well as temperature and pressure. The BMP280 has no humidity sensor.
How do I tell if my sensor is a BME280 or a BMP280?
Read the chip ID register: 0x60 is a BME280 and 0x58 is a BMP280. The BME280 chip is also square while the BMP280 is rectangular.
Can the BMP280 measure altitude?
Yes, from air pressure. Relative changes of about a metre are detectable; absolute altitude needs the current sea-level pressure.
Does the BME280 work with Arduino Uno at 5 V?
Only on modules with a 3.3 V regulator and level shifting. Check the board; otherwise use a level shifter.
Is the BME680 better than the BME280?
It adds a gas sensor for an indoor air quality index, but costs more and needs Bosch's BSEC library for the IAQ value.
Parts for this guide
Calculators
Terms in this guide
Projects that use it
Put this into practice: 24 step-by-step builds in our project library use parts from this guide.
Keep learning
Sources
Written by the Geekobot team from manufacturer datasheets. Always check the datasheet for the exact part and variant you buy.


