Component guide · Intermediate · 4 min read
4G with GNSS (Crowtail A7670E, 4G LTE GNSS BLE Shield, Vanix EC200U)

and Ready Trackers (SenseCAP T1000-A, HoneyComm)
By Geekobot Learning Team · Updated 29 Oct 2026
On this page
These products send location over a network. The Crowtail A7670E, 4G LTE GNSS shield and Vanix EC200U board combine a 4G modem and GNSS for vehicle and asset trackers you build yourself. The SenseCAP T1000-A is a ready LoRaWAN tracker card, and the HoneyComm units are finished GPS and Bluetooth trackers with apps. Each needs a SIM or network plan.
Key specs at a glance
- Network
- 4G LTE Cat-1 (A7670E, EC200U), LoRaWAN (T1000-A)
- GNSS
- GPS, GLONASS, BeiDou (model dependent)
- Interface
- UART AT commands (modules); app or LoRaWAN (trackers)
- Supply
- 5 V or Li-ion; modems need 2 A peaks
- SIM
- Nano or micro SIM with data
- Use
- Vehicle, asset and personal tracking
Models in this guide
These are alternatives. Pick the one that fits your project; you only need one.
Option 1Elecrow Crowtail-4G SIM A7670E Module w/ GPS GLONASS BDS₹3,439
Option 24G LTE GNSS BLE 5.0 IoT Shield for Arduino & Raspberry Pi₹4,011
Option 3Vanix Tracx-1b Quectel EC200U-CN 4G GPS Module₹2,639
Option 4SenseCAP T1000-A LoRaWAN Tracker₹4,717
Option 5HoneyComm HC039 Smart GPS Tracker w/ Magnetic Mount & 3-Year Battery₹1,779
Option 6HoneyComm HC034 Android Air Tracker GPS & BLE₹889
What the 4G GNSS modules and GPS trackers is
These products combine a 4G or LoRaWAN radio with GNSS so a device can find its position and send it to a server, either as modules you build with or as finished trackers.
Modems draw short current peaks of about 2 A when transmitting, so a weak USB supply causes resets. Use a good 5 V supply or a Li-ion cell.
For the A7670E, GNSS is turned on and read with AT commands (AT+CGNSSPWR=1, then AT+CGNSSINFO).
4G GNSS modules and GPS trackers pinout
The pins on the 4G GNSS modules and GPS trackers and what each one does.
| Pin | Function |
|---|---|
| VCC / VBAT | Supply |
| GND | Ground |
| TX / RX | UART AT commands |
| PWRKEY | Power on |
| GNSS antenna | Separate SMA or IPEX |
- VCC / VBAT
- Supply
- GND
- Ground
- TX / RX
- UART AT commands
- PWRKEY
- Power on
- GNSS antenna
- Separate SMA or IPEX
Wiring the 4G GNSS modules and GPS trackers
Connect the 4G GNSS modules and GPS trackers like this.
| 4G GNSS modules and GPS trackers pin | Arduino Uno | ESP32 |
|---|---|---|
| VCC | External 5 V 2 A | External 5 V 2 A |
| GND | GND (common) | GND (common) |
| TX | D10 (SoftwareSerial RX) | GPIO 16 |
| RX | D11 | GPIO 17 |
| PWRKEY | D7 | GPIO 4 |
- VCC
- Arduino Uno:
- External 5 V 2 A
- ESP32:
- External 5 V 2 A
- GND
- Arduino Uno:
- GND (common)
- ESP32:
- GND (common)
- TX
- Arduino Uno:
- D10 (SoftwareSerial RX)
- ESP32:
- GPIO 16
- RX
- Arduino Uno:
- D11
- ESP32:
- GPIO 17
- PWRKEY
- Arduino Uno:
- D7
- ESP32:
- GPIO 4
Example code
Quectel EC200U uses AT+QGPS=1 and AT+QGPSLOC=2 instead. Check your module's AT manual.
void at(const char *c, int wait = 1000) {
Serial2.println(c);
unsigned long t = millis();
while (millis() - t < wait) while (Serial2.available()) Serial.write(Serial2.read());
}
void setup() {
Serial.begin(115200);
Serial2.begin(115200, SERIAL_8N1, 16, 17);
at("AT");
at("AT+CGNSSPWR=1", 3000); // GNSS power on (A7670 series)
}
void loop() {
at("AT+CGNSSINFO"); // lat, lon, date, time, altitude, speed
delay(5000);
}Setup and tuning
use an active data SIM, disable its PIN lock in a phone first, and check the network supports LTE Cat-1 in your area.
4G modems draw 2 A peaks. Use a supply or Li-ion cell that can deliver this, with a large capacitor near the module.
connect both the LTE and GNSS antennas before powering up, and place the GNSS antenna with a clear view of the sky.
the first GNSS fix outdoors can take 30 seconds to a few minutes; later fixes are faster.
test with a USB-serial adapter first (AT, AT+CPIN?, AT+CSQ) before writing your own firmware.
What you need
Shop this list10 of 10 found in our store · ₹27,590
Elecrow Crowtail-4G SIM A7670E Module w/ GPS GLONASS BDS: the part this guide coversElecrow Crowtail-4G SIM A7670E Module w/ GPS GLONASS BDS₹3,439
4G LTE GNSS BLE 5.0 IoT Shield for Arduino & Raspberry Pi: another version this guide covers4G LTE GNSS BLE 5.0 IoT Shield for Arduino & Raspberry Pi₹4,011
Vanix Tracx-1b Quectel EC200U-CN 4G GPS Module: another version this guide coversVanix Tracx-1b Quectel EC200U-CN 4G GPS Module₹2,639
SenseCAP T1000-A LoRaWAN Tracker: another version this guide coversSenseCAP T1000-A LoRaWAN Tracker₹4,717
HoneyComm HC039 Smart GPS Tracker w/ Magnetic Mount & 3-Year Battery: another version this guide coversHoneyComm HC039 Smart GPS Tracker w/ Magnetic Mount & 3-Year Battery₹1,779
HoneyComm HC034 Android Air Tracker GPS & BLE: another version this guide coversHoneyComm HC034 Android Air Tracker GPS & BLE₹889
HoneyComm HC299 Air Tag Anti-Lost Tracker w/ Bluetooth & GPS: another version this guide coversHoneyComm HC299 Air Tag Anti-Lost Tracker w/ Bluetooth & GPS₹639
Waveshare SIM7600G-H 4G LTE and GNSS module: a 4G modem with GNSS built inWaveshare SIM7600G-H 4G LTE & GNSS Communication Module₹8,809
ESP32-WROOM-32 38-pin development board: for Wi-Fi logging and dashboardsESP32-WROOM-32 38-Pin Development Board₹389
GPS antenna 1575.42 MHz, SMA, 3 m cable: an external antenna for better receptionGPS Antenna 1575.42MHz SMA Male 3M Cable₹279Closest match, check the specs
Alternatives and when to choose them
- SIM808: 2G GSM with GPS.
- LilyGO T-Beam: LoRa and GPS.
- GNSS modules and trackers: overview.
Common mistakes to avoid
- Using a weak power supply, so the modem resets whenever it transmits.
- Leaving the SIM PIN lock on, so the modem never registers.
- Powering up without antennas, which can damage the RF stage.
- Testing GPS indoors and assuming the module is faulty.
Frequently asked questions
Do I need a SIM card for the 4G modules?
Yes. The 4G modules need an active data SIM. The SenseCAP T1000-A uses LoRaWAN instead and needs a LoRaWAN gateway or network.
Why does GPS not get a fix indoors?
GNSS signals are very weak and do not pass through roofs well. Test outdoors or by a window with a clear view of the sky.
Can an Arduino Uno run a 4G tracker?
It can send AT commands over serial, but an ESP32 or STM32 is easier, with more memory and a spare hardware UART.
How much data does a GPS tracker use?
Sending a position every minute uses only a few megabytes a month, so a small data plan is enough.
Will a 2G-only module work instead?
2G networks are shutting down in many regions, so a 4G Cat-1 module is the safer choice for new projects.
Parts for this guide
Keep learning
Sources
Written by the Geekobot team from manufacturer datasheets. Always check the datasheet for the exact part and variant you buy.
