Component guide · Intermediate · 4 min read
LilyGO T-Beam V1.2 and T-Beam Supreme

LoRa, GPS, Battery and Meshtastic
By Geekobot Learning Team · Updated 29 Oct 2026
On this page
The LilyGO T-Beam is an ESP32 board with a LoRa radio, a GPS receiver and an 18650 battery holder, managed by an AXP power chip. It is a ready-made GPS tracker, LoRaWAN mapper or Meshtastic node. The V1.2 uses an ESP32; the T-Beam Supreme moves to an ESP32-S3 with an L76K GPS, OLED and sensors. Check the radio chip and frequency on your board.
Key specs at a glance
- MCU
- ESP32 (V1.2) or ESP32-S3 (Supreme)
- Radio
- SX1276/SX1278 or SX1262 depending on version
- GPS
- NEO-6M or NEO-M8N (V1.2), L76K (Supreme)
- Power
- 18650 holder, AXP192/AXP2101 PMU, USB charging
- Extras
- Supreme: OLED, QMC6310 compass, BME280
- Related boards
- T-Lora C6 (ESP32-C6 + SX1262), T-TWR Plus (walkie-talkie)
A shorted, over-charged or damaged lithium cell can get very hot and catch fire. Use a protection board or BMS, never short the terminals, charge on a non-flammable surface and do not leave a charging pack alone. Throw away cells that are swollen or dented.
Models in this guide
These are alternatives. Pick the one that fits your project; you only need one.
Option 1LilyGO T-Beam V1.2 ESP32 LoRa 433MHz Module w/ GPS & IPEX₹4,889
Option 2LilyGO T-Beam V1.2 ESP32 LoRa 868MHz WiFi Bluetooth Module w/ IPEX & 18650 Holder₹5,249
Option 3LilyGO T-Beam SUPREME ESP32-S3 LoRa Development Board w/ L76K GPS 433MHz₹6,019
Option 4LilyGO T-Lora C6 ESP32-C6 LoRa SX1262 Dev Board₹2,209
Option 5LilyGO T-TWR Plus ESP32-S3 LoRa Walkie-Talkie Dev Board w/ OLED & GPS₹6,559
What the LilyGO T-Beam LoRa GPS board is
The power chip turns the GPS and LoRa supplies on and off. On the V1.2 with AXP2101, nothing happens until your code enables those rails through the XPowersLib library; the LilyGO examples do this at the start.
The V1.2 LoRa pins are NSS 18, SCK 5, MOSI 27, MISO 19, RST 23 and DIO0 26 (DIO1 33 for SX1262), with GPS on RX 34 and TX 12.
In India the licence-free LoRa band is 865 to 867 MHz (LoRaWAN plan IN865). 433 MHz modules are widely used by hobbyists, but check local rules before a commercial deployment.
LilyGO T-Beam LoRa GPS board pinout
The pins on the LilyGO T-Beam LoRa GPS board and what each one does.
| Pin | Function |
|---|---|
| LoRa NSS / SCK / MOSI / MISO | 18 / 5 / 27 / 19 (V1.2) |
| LoRa RST / DIO0 / DIO1 | 23 / 26 / 33 (V1.2) |
| GPS RX / TX | 34 / 12 (V1.2) |
| I2C SDA / SCL | 21 / 22, shared with the PMU |
| User button | GPIO 38 |
| 18650 | Battery holder on the back |
- LoRa NSS / SCK / MOSI / MISO
- 18 / 5 / 27 / 19 (V1.2)
- LoRa RST / DIO0 / DIO1
- 23 / 26 / 33 (V1.2)
- GPS RX / TX
- 34 / 12 (V1.2)
- I2C SDA / SCL
- 21 / 22, shared with the PMU
- User button
- GPIO 38
- 18650
- Battery holder on the back
Wiring the LilyGO T-Beam LoRa GPS board
Insert the 18650 with the right polarity: the holder has no reverse protection on some versions. Fit both the LoRa and GPS antennas before power-up.
| LilyGO T-Beam LoRa GPS board pin | T-Beam V1.2 | T-Beam Supreme |
|---|---|---|
| LoRa | Built in | Built in |
| GPS | Built in | Built in |
| OLED (optional) | SDA 21, SCL 22 | Built in |
| Battery | 18650 cell | 18650 cell |
- LoRa
- T-Beam V1.2:
- Built in
- T-Beam Supreme:
- Built in
- GPS
- T-Beam V1.2:
- Built in
- T-Beam Supreme:
- Built in
- OLED (optional)
- T-Beam V1.2:
- SDA 21, SCL 22
- T-Beam Supreme:
- Built in
- Battery
- T-Beam V1.2:
- 18650 cell
- T-Beam Supreme:
- 18650 cell
Example code
Boards with the older AXP192 use XPowersAXP192 and different rail names; LilyGO's repository has an example for each version. Add RadioLib to send the position over LoRa.
#include <TinyGPSPlus.h>
#include <XPowersLib.h>
XPowersAXP2101 pmu;
TinyGPSPlus gps;
HardwareSerial gpsSerial(1);
void setup() {
Serial.begin(115200);
Wire.begin(21, 22);
pmu.begin(Wire, AXP2101_SLAVE_ADDRESS, 21, 22);
pmu.setALDO3Voltage(3300); pmu.enableALDO3(); // GPS power
pmu.setALDO2Voltage(3300); pmu.enableALDO2(); // LoRa power
gpsSerial.begin(9600, SERIAL_8N1, 34, 12);
}
void loop() {
while (gpsSerial.available()) gps.encode(gpsSerial.read());
if (gps.location.isUpdated())
Serial.printf("%.6f, %.6f sats %d\n", gps.location.lat(), gps.location.lng(), gps.satellites.value());
}Setup and tuning
select ESP32 Dev Module (V1.2) or ESP32S3 Dev Module with PSRAM (Supreme).
flash T-Beam or T-Beam S3 Supreme from the web flasher and set region IN.
the first fix outdoors can take a few minutes; the backup battery speeds later fixes.
TTN Mapper firmware turns a T-Beam into a LoRaWAN coverage mapper.
What you need
Shop this list9 of 9 found in our store · ₹12,19,385
LilyGO T-Beam V1.2 ESP32 LoRa 433MHz Module w/ GPS & IPEX: the part this guide coversLilyGO T-Beam V1.2 ESP32 LoRa 433MHz Module w/ GPS & IPEX₹4,889
LilyGO T-Beam V1.2 ESP32 LoRa 868MHz WiFi Bluetooth Module w/ IPEX & 18650 Holder: another version this guide coversLilyGO T-Beam V1.2 ESP32 LoRa 868MHz WiFi Bluetooth Module w/ IPEX & 18650 Holder₹5,249
LilyGO T-Beam SUPREME ESP32-S3 LoRa Development Board w/ L76K GPS 433MHz: another version this guide coversLilyGO T-Beam SUPREME ESP32-S3 LoRa Development Board w/ L76K GPS 433MHz₹6,019
LilyGO T-Lora C6 ESP32-C6 LoRa SX1262 Dev Board: another version this guide coversLilyGO T-Lora C6 ESP32-C6 LoRa SX1262 Dev Board₹2,209
LilyGO T-TWR Plus ESP32-S3 LoRa Walkie-Talkie Dev Board w/ OLED & GPS: another version this guide coversLilyGO T-TWR Plus ESP32-S3 LoRa Walkie-Talkie Dev Board w/ OLED & GPS₹6,559
18650 Li-ion cell: battery power for a remote node18650 Li-ion Rechargeable Cell₹119Closest match, check the specs
868MHz 4dBi SMA antenna with 3 m cable: an outdoor antenna for 865 to 868 MHzLWC-868-MM-03 868MHz 4dBi SMA Antenna w/ 3m RG58 Cable₹412Closest match, check the specs
IPEX to SMA pigtail cable: to fit an SMA antenna to an IPEX socket5cm RG178 IPEX 1 to RP-SMA Female RF Pigtail Cable₹82Closest match, check the specs
USB to TTL serial converter: to talk to the module from a PCUSB to TTL Serial Converter (CH340G / CP2102 / FT232RL / PL2303)₹85Closest match, check the specs
Alternatives and when to choose them
- Heltec WiFi LoRa 32: smaller, no GPS or 18650 holder.
- SIM808 GSM and GPS: tracker over the mobile network instead of LoRa.
- NEO-6M GPS: the GPS receiver on its own.
Common mistakes to avoid
- Not enabling the PMU rails, so GPS and LoRa stay off.
- Using pins from a different T-Beam version.
- Reversed 18650.
- Testing GPS indoors.
Frequently asked questions
Which T-Beam for Meshtastic?
Both V1.2 and Supreme are supported; the Supreme has a better GPS and sensors.
Does it charge the 18650?
Yes, over USB through the PMU.
Can it be a LoRaWAN node?
Yes, with an LMIC or RadioLib LoRaWAN sketch and the right region.
What is the T-TWR Plus?
A LilyGO walkie-talkie dev board with an ESP32-S3 and radio module.
How long does the battery last?
A day or more as a Meshtastic node; longer with GPS updates spaced out.
Parts for this guide
Keep learning
Sources
- LilyGO T-Beam V1.2 and T-Beam Supreme documentation
- XPowersLib library
- Meshtastic supported hardware list
Written by the Geekobot team from manufacturer datasheets. Always check the datasheet for the exact part and variant you buy.


