Component guide · Intermediate · 4 min read
Heltec WiFi LoRa 32 V3 and ESP32 LoRa OLED Boards

Pins, Setup and Meshtastic
By Geekobot Learning Team · Updated 29 Oct 2026
On this page
Heltec's WiFi LoRa 32 boards combine an ESP32 or ESP32-S3, a LoRa radio and a 0.96 inch OLED on one board with a battery connector. V3 boards use the SX1262; older and generic copies use the SX1278. They are the quickest way to build a LoRa link, a single-channel test node or a Meshtastic handset. Choose the frequency version for your region.
Key specs at a glance
- MCU
- ESP32-S3 (V3, Wireless Stick, CT62 uses ESP32-C3) or ESP32 (older)
- Radio
- SX1262 (V3) or SX1278 (older 433 MHz boards)
- Display
- 0.96 inch SSD1306 OLED (not on Stick Lite or CT62)
- Power
- USB-C 5 V or 3.7 V Li-Po with on-board charging
- Wireless
- Wi-Fi, Bluetooth LE and LoRa
- Antenna
- IPEX or SMA LoRa antenna, supplied
Models in this guide
These are alternatives. Pick the one that fits your project; you only need one.
Option 1Heltec Automation LoRa32 V3 ESP32-S3 SX1262 OLED Development Board (433-510MHz)₹2,519
Option 2Heltec Automation ESP32-S3 LoRa Development Board V3 w/ SX1262 & OLED (433MHz)₹2,839
Option 3Heltec Automation LoRa ESP32 OLED Display Development Board w/ SX1262₹2,809
Option 4Heltec Automation ESP32 LoRa SX1278 0.96-Inch OLED WiFi Module₹2,739
Option 5ESP32 LoRa SX1278 0.96-Inch OLED Display Module w/ Type-C₹2,179
Option 6Heltec Automation Wireless Stick ESP32-S3 v3 LoRaWAN BLE Dev Board w/ OLED₹2,319
What the Heltec ESP32 LoRa OLED board is
On the V3 the LoRa pins are fixed: NSS 8, SCK 9, MOSI 10, MISO 11, RST 12, BUSY 13 and DIO1 14. The OLED is on SDA 17, SCL 18 with reset 21, and its power is switched by GPIO 36 (Vext). Older SX1278 boards use NSS 18, RST 14 and DIO0 26.
Meshtastic, an open source off-grid messaging firmware, supports the V3 directly; flash it from the web flasher and pair a phone over Bluetooth.
In India the licence-free LoRa band is 865 to 867 MHz (LoRaWAN plan IN865). 433 MHz modules are widely used by hobbyists, but check local rules before a commercial deployment.
Heltec ESP32 LoRa OLED board pinout
The pins on the Heltec ESP32 LoRa OLED board and what each one does.
| Pin | Function |
|---|---|
| LoRa NSS / SCK / MOSI / MISO | GPIO 8 / 9 / 10 / 11 (V3) |
| LoRa RST / BUSY / DIO1 | GPIO 12 / 13 / 14 (V3) |
| OLED SDA / SCL / RST | GPIO 17 / 18 / 21 (V3) |
| Vext | GPIO 36, LOW turns on OLED and external 3.3 V |
| VBAT ADC | GPIO 1 with ADC_Ctrl on GPIO 37 |
| PRG button | GPIO 0 |
| LED | GPIO 35 |
- LoRa NSS / SCK / MOSI / MISO
- GPIO 8 / 9 / 10 / 11 (V3)
- LoRa RST / BUSY / DIO1
- GPIO 12 / 13 / 14 (V3)
- OLED SDA / SCL / RST
- GPIO 17 / 18 / 21 (V3)
- Vext
- GPIO 36, LOW turns on OLED and external 3.3 V
- VBAT ADC
- GPIO 1 with ADC_Ctrl on GPIO 37
- PRG button
- GPIO 0
- LED
- GPIO 35
Wiring the Heltec ESP32 LoRa OLED board
Everything is on the board, so only the antenna and an optional battery need connecting. Never power up without the LoRa antenna fitted. Use a 3.7 V Li-Po with the correct JST 1.25 polarity.
| Heltec ESP32 LoRa OLED board pin | Uno | Heltec V3 |
|---|---|---|
| LoRa radio | Built in | Built in |
| OLED | Built in | Built in |
| Battery | JST 1.25 Li-Po | JST 1.25 Li-Po |
| Sensor (I2C) | Use GPIO 41/42 on V3 | Use GPIO 41/42 on V3 |
- LoRa radio
- Uno:
- Built in
- Heltec V3:
- Built in
- OLED
- Uno:
- Built in
- Heltec V3:
- Built in
- Battery
- Uno:
- JST 1.25 Li-Po
- Heltec V3:
- JST 1.25 Li-Po
- Sensor (I2C)
- Uno:
- Use GPIO 41/42 on V3
- Heltec V3:
- Use GPIO 41/42 on V3
Example code
Install the Heltec ESP32 board package or use the generic ESP32-S3 Dev Module. For older SX1278 boards use the LoRa library with LoRa.setPins(18, 14, 26).
#include <RadioLib.h>
#include <Wire.h>
#include <Adafruit_SSD1306.h>
SX1262 radio = new Module(8, 14, 12, 13); // NSS, DIO1, RST, BUSY
Adafruit_SSD1306 oled(128, 64, &Wire, 21);
int count = 0;
void setup() {
pinMode(36, OUTPUT); digitalWrite(36, LOW); // Vext on (OLED power)
Wire.begin(17, 18);
oled.begin(SSD1306_SWITCHCAPVCC, 0x3C);
SPI.begin(9, 11, 10, 8); // SCK, MISO, MOSI, NSS
radio.begin(865.0); // set your band
}
void loop() {
String msg = "count " + String(count++);
int s = radio.transmit(msg);
oled.clearDisplay(); oled.setTextColor(SSD1306_WHITE);
oled.setCursor(0, 0); oled.println(msg);
oled.println(s == RADIOLIB_ERR_NONE ? "sent" : "error");
oled.display();
delay(5000);
}Setup and tuning
add Heltec's ESP32 board URL, or pick ESP32S3 Dev Module with USB CDC on boot enabled.
flash from flasher.meshtastic.org, choose Heltec V3 and set region IN in the app.
read voltage only after setting ADC_Ctrl, and use deep sleep for long life.
the 433 MHz and 868/915 MHz boards look identical; check the label.
What you need
Shop this list15 of 15 found in our store · ₹12,13,191
Heltec Automation Automation LoRa32 V3 ESP32-S3 SX1262 OLED Development Board (433-510MHz): the part this guide coversHeltec Automation LoRa32 V3 ESP32-S3 SX1262 OLED Development Board (433-510MHz)₹2,519
Heltec Automation Automation ESP32-S3 LoRa Development Board V3 w/ SX1262 & OLED (433MHz): another version this guide coversHelical Spring Coil Antenna₹40
Heltec Automation Automation LoRa ESP32 OLED Display Development Board w/ SX1262: another version this guide coversHeltec Automation LoRa ESP32 OLED Display Development Board w/ SX1262₹2,809Closest match, check the specs
Heltec Automation Automation ESP32 LoRa SX1278 0.96-Inch OLED WiFi Module: another version this guide coversHeltec Automation ESP32 LoRa SX1278 0.96-Inch OLED WiFi Module₹2,739Closest match, check the specs
ESP32 LoRa SX1278 0.96-Inch OLED Display Module w/ Type-C: another version this guide coversESP32 LoRa SX1278 0.96-Inch OLED Display Module w/ Type-C₹2,179
Heltec Automation Automation Wireless Stick ESP32-S3 v3 LoRaWAN BLE Dev Board w/ OLED: another version this guide coversHeltec Automation Wireless Stick ESP32-S3 v3 LoRaWAN BLE Dev Board w/ OLED₹2,319
Heltec Automation Automation Wireless Stick Lite ESP32-S3 SX1262 LoRa Node (863-928MHz): another version this guide coversHeltec Automation Wireless Stick Lite ESP32-S3 SX1262 LoRa Node (863-928MHz)₹2,209
Heltec Automation Automation ESP32-S3 Wireless Shell Module w/ SX1262 LoRaWAN, Wi-Fi, BLE: another version this guide coversHeltec Automation ESP32-S3 Wireless Shell Module w/ SX1262 LoRaWAN, Wi-Fi, BLE₹1,559
Heltec Automation Automation CT62 LoRa/Wi-Fi/BLE Node w/ ESP32-C3 & SX1262 (868MHz): another version this guide coversHeltec Automation CT62 LoRa/Wi-Fi/BLE Node w/ ESP32-C3 & SX1262 (868MHz)₹1,159
Heltec Automation Automation CT62 LoRa Module ESP32-C3 SX1262 433-510MHz: another version this guide coversHeltec Automation CT62 LoRa Module ESP32-C3 SX1262 433-510MHz₹859
18650 Li-ion cell: battery power for a remote node18650 Li-ion Rechargeable Cell₹119Closest match, check the specs
868MHz 4dBi SMA antenna with 3 m cable: an outdoor antenna for 865 to 868 MHzLWC-868-MM-03 868MHz 4dBi SMA Antenna w/ 3m RG58 Cable₹412Closest match, check the specs
IPEX to SMA pigtail cable: to fit an SMA antenna to an IPEX socket5cm RG178 IPEX 1 to RP-SMA Female RF Pigtail Cable₹82Closest match, check the specs
DS18B20 waterproof temperature probe: a sensor to send over LoRaSonoff DS18B20 Waterproof Temperature Sensor Probe w/ 1m Cable – 1-Wire Interface₹340Closest match, check the specs
USB to TTL serial converter: to talk to the module from a PCUSB to TTL Serial Converter (CH340G / CP2102 / FT232RL / PL2303)₹85Closest match, check the specs
Alternatives and when to choose them
- LilyGO T-Beam: adds GPS and an 18650 holder.
- Heltec CubeCell: lower power LoRaWAN node without Wi-Fi.
- SX1262 LoRa module: the radio on its own.
Common mistakes to avoid
- Copying old SX1278 board pins to a V3.
- Forgetting to turn on Vext, so the OLED stays blank.
- Transmitting without the antenna.
- Buying the 433 MHz version for an 865 MHz network.
Frequently asked questions
Does it work with Meshtastic?
Yes, the WiFi LoRa 32 V3 and Wireless Stick V3 are supported targets.
Can it be a LoRaWAN gateway?
Only a single-channel test gateway; real gateways use SX1302 concentrators.
Which library?
RadioLib for SX1262 boards, LoRa (Sandeep Mistry) for SX1278 boards.
How long on a battery?
Days with Wi-Fi off and deep sleep; hours with Wi-Fi and the OLED on.
What is the CT62?
A tiny ESP32-C3 plus SX1262 module for building your own node.
Parts for this guide
Keep learning
Sources
- Heltec WiFi LoRa 32 V3 schematic and pin map
- Meshtastic supported hardware list
- RadioLib documentation
Written by the Geekobot team from manufacturer datasheets. Always check the datasheet for the exact part and variant you buy.



