Component guide · Intermediate · 4 min read
SX1262 LoRa Module

Pinout, Wiring and RadioLib Code
By Geekobot Learning Team · Updated 29 Oct 2026
On this page
The Semtech SX1262 is the newer LoRa transceiver that replaces the SX1276 in most current LoRaWAN and Meshtastic devices. It transmits up to 22 dBm, draws less current when receiving, and covers 150 to 960 MHz, so the same chip serves 433, 868 and 915 MHz boards. It connects over SPI with extra BUSY and DIO1 pins and runs at 3.3 V; RadioLib is the easiest library.
Key specs at a glance
- Chip
- Semtech SX1262 (SX1268 is the China-band twin)
- Frequency
- 150 to 960 MHz (module tuned for one band, e.g. 433, 868 or 915)
- Output power
- Up to +22 dBm (1 W on E22-M30S modules with a PA)
- Sensitivity
- Down to about -148 dBm
- Interface
- SPI plus BUSY, DIO1, RESET (and RXEN/TXEN on some modules)
- Supply
- 3.3 V logic, about 4.6 mA receiving
Models in this guide
These are alternatives. Pick the one that fits your project; you only need one.
Option 1G-NiceRF LoRa1262-915 SX1262 915MHz LoRa Module w/ ESD Protection₹889
Option 2EByte E22-900M22S SX1262 900MHz LoRa Module SMD w/ TCXO₹669
Option 3EByte E22-900M30S SX1262/SX1268 1W 900MHz LoRa Module₹1,039
Option 4EByte E22-900T22D-V2 SX1262 LoRa 868MHz Module w/ SMA-K Antenna₹989
Option 5IndieSemiC ISC-SX1262-B LoRa Module – SX1262 Transceiver, 868/915MHz₹549
Option 6LRTC-1262 LoRa Transceiver Module, SX1262₹452
What the SX1262 LoRa module is
LoRa trades speed for range: a few hundred bytes per second can reach several kilometres line-of-sight. Compared with the SX1276, the SX1262 has a cleaner command interface (it waits on a BUSY pin), more power and lower receive current.
It is not pin-compatible with SX1276 boards, and the libraries differ, so check the chip before copying code. Modules include EByte E22, Seeed Wio-SX1262, Waveshare Core1262 and Raspberry Pi HATs.
SX1262 LoRa module pinout
The pins on the SX1262 LoRa module and what each one does.
| Pin | Function |
|---|---|
| VCC / GND | 3.3 V supply and ground |
| SCK / MOSI / MISO | SPI bus |
| NSS (CS) | SPI chip select |
| BUSY | HIGH while the chip is busy; wait for LOW before each command |
| DIO1 | Interrupt: transmit done, packet received |
| NRST | Reset, active low |
| RXEN / TXEN | RF switch control on modules that have them (E22) |
| ANT | Antenna (u.FL, SMA or pad) |
- VCC / GND
- 3.3 V supply and ground
- SCK / MOSI / MISO
- SPI bus
- NSS (CS)
- SPI chip select
- BUSY
- HIGH while the chip is busy; wait for LOW before each command
- DIO1
- Interrupt: transmit done, packet received
- NRST
- Reset, active low
- RXEN / TXEN
- RF switch control on modules that have them (E22)
- ANT
- Antenna (u.FL, SMA or pad)
Wiring the SX1262 LoRa module
The SX1262 is 3.3 V only. An ESP32, RP2040 or nRF52 connects directly; a 5 V Uno needs level shifting on every line. Always connect the antenna before transmitting.
| SX1262 LoRa module pin | Arduino Uno | ESP32 |
|---|---|---|
| VCC | 3.3V (with level shifter on signals) | 3V3 |
| GND | GND | GND |
| SCK | D13 | GPIO 18 |
| MISO | D12 | GPIO 19 |
| MOSI | D11 | GPIO 23 |
| NSS | D10 | GPIO 5 |
| BUSY | D4 | GPIO 4 |
| DIO1 | D2 | GPIO 26 |
| NRST | D3 | GPIO 14 |
- VCC
- Arduino Uno:
- 3.3V (with level shifter on signals)
- ESP32:
- 3V3
- GND
- Arduino Uno:
- GND
- ESP32:
- GND
- SCK
- Arduino Uno:
- D13
- ESP32:
- GPIO 18
- MISO
- Arduino Uno:
- D12
- ESP32:
- GPIO 19
- MOSI
- Arduino Uno:
- D11
- ESP32:
- GPIO 23
- NSS
- Arduino Uno:
- D10
- ESP32:
- GPIO 5
- BUSY
- Arduino Uno:
- D4
- ESP32:
- GPIO 4
- DIO1
- Arduino Uno:
- D2
- ESP32:
- GPIO 26
- NRST
- Arduino Uno:
- D3
- ESP32:
- GPIO 14
Example code
Install RadioLib by Jan Gromeš. Use the frequency your module is built for and that is allowed where you are (865-867 MHz in India). Some modules need setTCXO(1.8) or RXEN/TXEN pins set in code.
#include <RadioLib.h>
// NSS, DIO1, NRST, BUSY
SX1262 radio = new Module(5, 26, 14, 4);
void setup() {
Serial.begin(115200);
// 868.0 MHz, 125 kHz bandwidth, SF9, CR 4/7, sync word, 14 dBm
int state = radio.begin(868.0, 125.0, 9, 7, RADIOLIB_SX126X_SYNC_WORD_PRIVATE, 14);
if (state != RADIOLIB_ERR_NONE) { Serial.print("LoRa failed: "); Serial.println(state); while (1); }
radio.setDio2AsRfSwitch(true); // many modules use DIO2 for the RF switch
}
void loop() {
int state = radio.transmit("Hello from SX1262");
Serial.println(state == RADIOLIB_ERR_NONE ? "Sent" : "Send failed");
delay(5000);
}Setup and tuning
an 868 MHz module will not work well on 433 MHz even though the chip can tune there.
modules with a TCXO need radio.setTCXO(1.8) (or the voltage in their datasheet) before begin.
transmitting without an antenna can damage the PA, especially on 1 W modules.
start with SF9 and 125 kHz; raise the spreading factor for range, lower it for speed.
What you need
Shop this list16 of 16 found in our store · ₹15,436
G-NiceRF LoRa1262-915 SX1262 915MHz LoRa Module w/ ESD Protection: the part this guide coversG-NiceRF LoRa1262-915 SX1262 915MHz LoRa Module w/ ESD Protection₹889
EByte E22-900M22S SX1262 900MHz LoRa Module SMD w/ TCXO: another version this guide coversEByte E22-900M22S SX1262 900MHz LoRa Module SMD w/ TCXO₹669
EByte E22-900M30S SX1262/SX1268 1W 900MHz LoRa Module: another version this guide coversEByte E22-900M30S SX1262/SX1268 1W 900MHz LoRa Module₹1,039
EByte E22-900T22D-V2 SX1262 LoRa 868MHz Module w/ SMA-K Antenna: another version this guide coversEByte E22-900T22D-V2 SX1262 LoRa 868MHz Module w/ SMA-K Antenna₹989
IndieSemiC ISC-SX1262-B LoRa Module – SX1262 Transceiver, 868/915MHz: another version this guide coversIndieSemiC ISC-SX1262-B LoRa Module – SX1262 Transceiver, 868/915MHz₹549
LRTC-1262 LoRa Transceiver Module, SX1262: another version this guide coversLRTC-1262 LoRa Transceiver Module, SX1262₹452
LWM2-62 LoRaWAN Module, SX1262: another version this guide coversLWM2-62 LoRaWAN Module, SX1262₹835
Seeed Studio Studio Wio-SX1262 LoRa Module for XIAO: another version this guide coversSeeed Studio Wio-SX1262 LoRa Module for XIAO₹1,989Closest match, check the specs
Seeed Studio Studio Wio-SX1262-LF LoRa Module (433/470MHz, SX1262): another version this guide coversSeeed Studio Wio-SX1262-LF LoRa Module (433/470MHz, SX1262)₹689Closest match, check the specs
Waveshare Core1262 HF 850-930MHz LoRa Module w/ SX1262: another version this guide coversWaveshare Core1262 HF 850-930MHz LoRa Module w/ SX1262₹789
Waveshare SX1262 LoRa HAT for Raspberry Pi 868MHz: another version this guide coversWaveshare SX1262 LoRa HAT for Raspberry Pi 868MHz₹2,885
Waveshare SX1262 LoRa HAT for Raspberry Pi 915MHz: another version this guide coversWaveshare SX1262 LoRa HAT for Raspberry Pi 915MHz₹2,885
ESP32-WROOM-32 38-pin development board: for Wi-Fi logging and dashboardsESP32-WROOM-32 38-Pin Development Board₹389
LoRa antenna 433 MHz SMA: choose the antenna for your module's bandWaveshare LPWA LoRa Antenna₹200Closest match, check the specs
0.96 inch OLED display 128x64: to show readings without a computer0.96" OLED Display 128x64₹139Closest match, check the specs
Dupont jumper wires: for the connectionsDupont Jumper Wires (40 pcs)₹49Closest match, check the specs
Alternatives and when to choose them
- LoRa SX1278 and SX1276: the older, widely used LoRa chips.
- LoRaWAN nodes and gateways: building a network with The Things Network.
- HC-12 wireless module: simple 433 MHz serial link without LoRa.
Common mistakes to avoid
- Using SX1276 code or libraries with an SX1262.
- Not waiting for BUSY, or leaving BUSY unconnected.
- Forgetting setTCXO or the RF switch pins, so nothing transmits.
- Transmitting with no antenna connected.
Frequently asked questions
SX1262 or SX1276?
SX1262 for new designs: more power, lower receive current and current library support.
Does it work with Meshtastic?
Yes, most Meshtastic devices use the SX1262.
What frequency should I use in India?
865 to 867 MHz; check the rules for your country.
Can I use it with Arduino Uno?
Only with level shifting; a 3.3 V board such as an ESP32 is much simpler.
How far can it reach?
Several kilometres line-of-sight with good antennas; a few hundred metres in a city.
Parts for this guide
Projects that use it
Put this into practice: 57 step-by-step builds in our project library use parts from this guide.
Keep learning
Sources
Written by the Geekobot team from manufacturer datasheets. Always check the datasheet for the exact part and variant you buy.

