Component guide · Beginner · 4 min read
Arduino Display Shields

3.5 Inch ILI9486 TFT and Touch Shields, 4D Systems uLCD-32PTU, 1602 LCD Keypad Shield, Mega TFT Expansion Shield, Waveshare 2.8 Inch Touch Shield, E-Paper Driver Shield, Colorduino and GIGA Display Shield
By Geekobot Learning Team · Updated 29 Oct 2026
On this page
Display shields plug a screen straight onto an Arduino. The 1602 LCD keypad shield is the easiest: a 16x2 text LCD and five buttons on one analog pin. 3.5 inch ILI9486 shields use an 8-bit parallel bus and MCUFRIEND_kbv. The 2.8 inch Waveshare shield adds touch. The GIGA Display Shield is an 800x480 touch screen for the Arduino GIGA R1.
Key specs at a glance
- 1602 keypad
- 16x2 LCD, 5 buttons on A0
- ILI9486 3.5 inch
- 480x320, 8-bit parallel, uses most Uno pins
- Waveshare 2.8 inch
- 320x240, SPI, resistive touch, microSD
- 4D uLCD-32PTU
- Smart display with its own processor, serial commands
- E-paper shield
- Drives Waveshare SPI e-paper panels
- GIGA Display
- 3.97 inch 800x480 touch, IMU, microphone, camera connector
Models in this guide
These are alternatives. Pick the one that fits your project; you only need one.
Option 13.5″ ILI9486 TFT LCD Module 480×320 for Arduino Uno₹989
Option 23.5″ ILI9486 TFT Touch Shield LCD 480×320 for Arduino Uno₹909
Option 34D Systems 3.2″ uLCD-32PTU-AR LCD Module w/ Arduino Shield₹8,799
Option 4Arduino 1602 LCD Keypad Shield – Blue Backlight₹190
Option 5TFT LCD Expansion Shield V2.2 for Arduino MEGA₹237
Option 6Waveshare 2.8inch Touch LCD Shield₹1,619
What the Arduino TFT, LCD keypad, e-paper and LED matrix shields is
Display shields plug a screen straight onto an Arduino header, from a 16x2 text LCD with buttons to full-colour touch TFTs.
The 3.5 inch parallel shields use almost every Uno pin, leaving only A5 and a few digital pins free; a Mega has spare pins. The Mega TFT expansion shield adapts these screens to the Mega's faster port.
On the LCD keypad shield, all buttons share A0 through a resistor ladder, so read A0 and compare against ranges. Clone shields have slightly different values.
Arduino TFT, LCD keypad, e-paper and LED matrix shields pinout
The pins on the Arduino TFT, LCD keypad, e-paper and LED matrix shields and what each one does.
| Pin | Function |
|---|---|
| Uno R3 headers | D0-D13, A0-A5, power pins and the IOREF pin |
| ICSP header | SPI on 6 pins, used by many shields |
| IOREF | Tells the shield whether the board is 5V or 3.3V |
| Stacking headers | Let another shield sit on top |
| Reset button | Repeated on top of most shields |
- Uno R3 headers
- D0-D13, A0-A5, power pins and the IOREF pin
- ICSP header
- SPI on 6 pins, used by many shields
- IOREF
- Tells the shield whether the board is 5V or 3.3V
- Stacking headers
- Let another shield sit on top
- Reset button
- Repeated on top of most shields
Wiring the Arduino TFT, LCD keypad, e-paper and LED matrix shields
Some 3.5 inch shields are 3.3V-only screens with level shifting on board; do not remove parts. Remove the screen's protective film after testing.
| Arduino TFT, LCD keypad, e-paper and LED matrix shields pin | Connection | Note |
|---|---|---|
| Shield | Straight onto Uno or Mega | Check the screen sits clear of USB |
| Touch | Shares pins with the display | Calibrate first |
| E-paper panel | FPC cable into the shield | Contacts facing the right way |
- Shield
- Connection:
- Straight onto Uno or Mega
- Note:
- Check the screen sits clear of USB
- Touch
- Connection:
- Shares pins with the display
- Note:
- Calibrate first
- E-paper panel
- Connection:
- FPC cable into the shield
- Note:
- Contacts facing the right way
Example code
Print analogRead(A0) to the serial monitor to tune the ranges for your shield. For ILI9486 shields, run MCUFRIEND_kbv's diagnose example first.
#include <LiquidCrystal.h>
LiquidCrystal lcd(8, 9, 4, 5, 6, 7);
const char* key(int v) {
if (v < 60) return "RIGHT ";
if (v < 200) return "UP ";
if (v < 400) return "DOWN ";
if (v < 600) return "LEFT ";
if (v < 800) return "SELECT";
return "none ";
}
void setup() { lcd.begin(16, 2); lcd.print("Press a key"); }
void loop() {
lcd.setCursor(0, 1);
lcd.print(key(analogRead(A0)));
delay(100);
}Setup and tuning
use LiquidCrystal for the 1602 keypad shield and MCUFRIEND_kbv for ILI9486 parallel shields.
parallel TFT shields use almost all Uno pins. Plan other sensors on the remaining pins or use a Mega.
turn the pot on the 1602 shield until the characters appear; blank blocks mean the contrast is wrong.
run the touch calibration sketch and copy its values into your code.
read the 1602 shield buttons with analogRead on A0 and compare value ranges.
What you need
Shop this list9 of 10 found in our store · ₹22,280
3.5″ ILI9486 TFT LCD Module 480×320 for Arduino Uno: the part this guide covers3.5″ ILI9486 TFT LCD Module 480×320 for Arduino Uno₹989
3.5″ ILI9486 TFT Touch Shield LCD 480×320 for Arduino Uno: another version this guide covers3.5″ ILI9486 TFT Touch Shield LCD 480×320 for Arduino Uno₹909
4D Systems 3.2″ uLCD-32PTU-AR LCD Module w/ Arduino Shield: another version this guide covers4D Systems 3.2″ uLCD-32PTU-AR LCD Module w/ Arduino Shield₹8,799
Arduino 1602 LCD Keypad Shield – Blue Backlight: another version this guide coversArduino 1602 LCD Keypad Shield – Blue Backlight₹190
TFT LCD Expansion Shield V2.2 for Arduino MEGA: another version this guide coversTFT LCD Expansion Shield V2.2 for Arduino MEGA₹237
Waveshare 2.8inch Touch LCD Shield: another version this guide coversWaveshare 2.8inch Touch LCD Shield₹1,619
Waveshare E-Paper Driver Shield (B) for Arduino NUCLEO: another version this guide coversWaveshare E-Paper Driver Shield (B) for Arduino NUCLEO₹809
Colorduino LED RGB Driver Board w/ 5mm 8×8 Matrix for Arduino: another version this guide coversColorduino LED RGB Driver Board w/ 5mm 8×8 Matrix for Arduino₹1,609
Arduino GIGA Display Shield ASX00039: another version this guide coversArduino GIGA Display Shield ASX00039₹7,119- Uno R3 development board: the controller used in the wiring tableFind this part
Alternatives and when to choose them
- ILI9488 TFT display: SPI module version.
- ILI9341 touch display: 2.4-2.8 inch SPI.
- Waveshare e-paper modules: panels for the shield.
Common mistakes to avoid
- Adding sensors on pins already used by the TFT shield.
- Leaving the 1602 contrast pot at the wrong setting.
- Using touch values without running calibration.
- Picking a library for a different controller chip.
Frequently asked questions
Why does my 1602 keypad shield show only blocks?
The contrast pot is set wrong or the LCD is not initialised. Adjust the pot and check the pin numbers in LiquidCrystal.
Can I use a 3.5 inch TFT shield with sensors?
Only on the few free pins. The parallel bus uses most of the Uno, so a Mega or an SPI display is better for bigger projects.
Does the 3.5 inch shield work on a Mega?
Yes, it fits the Mega header and MCUFRIEND_kbv supports it, though it is slower than on an Uno.
How do I read the five buttons on the LCD shield?
They share A0 through resistors. Read A0 and match the value to each button's range.
What is the 4D Systems display good for?
It has its own processor, so the Arduino sends simple serial commands while the screen handles graphics and touch.
Parts for this guide
Keep learning
Sources
Written by the Geekobot team from manufacturer datasheets. Always check the datasheet for the exact part and variant you buy.

