Component guide · Intermediate · 4 min read
SPI E-Paper Display Modules (1.02 to 13.3 inch)

Wiring and Code
By Geekobot Learning Team · Updated 29 Oct 2026
On this page
E-paper (e-ink) modules keep their image with no power and are readable in sunlight, ideal for labels, weather stations and photo frames. All the modules here use the same 8-pin SPI interface (VCC, GND, DIN, CLK, CS, DC, RST, BUSY) and 3.3 V logic, from 1.02 inch black and white up to 13.3 inch Spectra 6 full colour. A full refresh takes 2 seconds (black and white) to 15 to 30 seconds (colour).
Key specs at a glance
- Sizes
- 1.02, 1.54, 2.13, 2.7, 2.9, 3.6, 7.3 and 13.3 inch
- Colours
- Black/white, black/white/red (3-colour), Spectra 6 (6 colours)
- Interface
- 4-wire SPI plus DC, RST and BUSY
- Logic
- 3.3 V (Waveshare driver boards include a level shifter for 5 V)
- Power
- Only during refresh, a few mA; zero to hold the image
- Refresh
- About 2 s (B/W full), 0.3 s (B/W partial), 15 to 30 s (colour)
Models in this guide
These are alternatives. Pick the one that fits your project; you only need one.
Option 12.13 Inch E-Paper Display Module, Black and White₹1,144
Option 2Waveshare 1.54 inch E-Ink Display Module, 200x200, Black/White₹1,350
Option 3Waveshare 1.54 inch E-Ink Display Module, 3-Colour, 200x200₹1,285
Option 4Waveshare 2.9 inch E-Paper Display Module (B), Red/Black/White₹1,900
Option 5Waveshare 1.02 inch E-Ink Display Module, 128x80₹1,450
Option 6Waveshare E-Paper Display HAT for Raspberry Pi₹2,450
What the SPI e-paper module is
Each size has its own controller and resolution, so the code must name the exact panel. The GxEPD2 Arduino library and Waveshare's Python and C examples cover all of these.
The HAT and photo-frame versions plug onto a Raspberry Pi; the bare modules come with a driver board or a cable to the 8-pin header.
SPI e-paper module pinout
The pins on the SPI e-paper module and what each one does.
| Pin | Function |
|---|---|
| VCC | 3.3 V (5 V only on driver boards with a regulator) |
| GND | Ground |
| DIN | SPI MOSI |
| CLK | SPI SCK |
| CS | Chip select |
| DC | Data / command |
| RST | Reset |
| BUSY | HIGH (or LOW) while refreshing |
- VCC
- 3.3 V (5 V only on driver boards with a regulator)
- GND
- Ground
- DIN
- SPI MOSI
- CLK
- SPI SCK
- CS
- Chip select
- DC
- Data / command
- RST
- Reset
- BUSY
- HIGH (or LOW) while refreshing
Wiring the SPI e-paper module
An Uno has only 2 KB RAM, which is too little for anything above about 1.54 inch without paging; use an ESP32 for 2.9 inch and larger. On a Raspberry Pi use the HAT, or SPI0 with DC on GPIO 25, RST on GPIO 17 and BUSY on GPIO 24.
| SPI e-paper module pin | Arduino Uno | ESP32 |
|---|---|---|
| VCC / GND | 3.3V / GND | 3V3 / GND |
| DIN | D11 (through level shifter if bare) | GPIO 23 |
| CLK | D13 | GPIO 18 |
| CS | D10 | GPIO 5 |
| DC | D9 | GPIO 17 |
| RST | D8 | GPIO 16 |
| BUSY | D7 | GPIO 4 |
- VCC / GND
- Arduino Uno:
- 3.3V / GND
- ESP32:
- 3V3 / GND
- DIN
- Arduino Uno:
- D11 (through level shifter if bare)
- ESP32:
- GPIO 23
- CLK
- Arduino Uno:
- D13
- ESP32:
- GPIO 18
- CS
- Arduino Uno:
- D10
- ESP32:
- GPIO 5
- DC
- Arduino Uno:
- D9
- ESP32:
- GPIO 17
- RST
- Arduino Uno:
- D8
- ESP32:
- GPIO 16
- BUSY
- Arduino Uno:
- D7
- ESP32:
- GPIO 4
Example code
GxEPD2's examples list the class for every panel; 3-colour panels use GxEPD2_3C and Spectra 6 panels use GxEPD2_7C. Use Waveshare's Python library on a Raspberry Pi.
#include <GxEPD2_BW.h>
#include <Fonts/FreeMonoBold12pt7b.h>
// CS, DC, RST, BUSY. Pick the class that matches your panel's controller.
GxEPD2_BW<GxEPD2_213_BN, GxEPD2_213_BN::HEIGHT> display(GxEPD2_213_BN(5, 17, 16, 4));
void setup() {
display.init(115200);
display.setRotation(1);
display.setFont(&FreeMonoBold12pt7b);
display.setFullWindow();
display.firstPage();
do {
display.fillScreen(GxEPD_WHITE);
display.setTextColor(GxEPD_BLACK);
display.setCursor(10, 40);
display.print("Hello e-paper");
} while (display.nextPage());
display.hibernate(); // panel keeps the image with no power
}
void loop() {}Setup and tuning
check the panel version on the flex cable (for example V2, V3 or B) and choose the matching driver.
do a full refresh every few partial updates to clear ghosting.
refresh at most every few minutes; they are slow and draw more current while refreshing.
store panels away from sunlight and above 0 C; update a stored panel every few weeks.
do not bend the ribbon sharply at the panel edge.
What you need
Shop this list15 of 15 found in our store · ₹73,941
2.13 Inch E-Paper Display Module, Black and White: the part this guide covers2.13 Inch E-Paper Display Module, Black and White₹1,144
Waveshare 1.54 inch E-Ink Display Module, 200x200, Black/White: another version this guide coversWaveshare 1.54 inch E-Ink Display Module, 200x200, Black/White₹1,350
Waveshare 1.54 inch E-Ink Display Module, 3-Colour, 200x200: another version this guide coversWaveshare 1.54 inch E-Ink Display Module, 3-Colour, 200x200₹1,285
Waveshare 2.9 inch E-Paper Display Module (B), Red/Black/White: another version this guide coversWaveshare 2.9 inch E-Paper Display Module (B), Red/Black/White₹1,900
Waveshare 1.02 inch E-Ink Display Module, 128x80: another version this guide coversWaveshare 1.02 inch E-Ink Display Module, 128x80₹1,450
Waveshare E-Paper Display HAT for Raspberry Pi: another version this guide coversWaveshare E-Paper Display HAT for Raspberry Pi₹2,450
Waveshare 3.6 inch Full-Colour E-Paper Display (Spectra 6), 600x400: another version this guide coversWaveshare 3.6 inch Full-Colour E-Paper Display (Spectra 6), 600x400₹5,050
Waveshare 7.3 inch 6-Colour E-Paper Display, 800x480: another version this guide coversWaveshare 7.3 inch 6-Colour E-Paper Display, 800x480₹10,600
Waveshare 13.3 inch Spectra 6 Full-Colour E-Paper Display, 1600x1200: another version this guide coversWaveshare 13.3 inch Spectra 6 Full-Colour E-Paper Display, 1600x1200₹35,650
Waveshare 7.3 inch Full-Colour E-Paper Photo Frame for Raspberry Pi Zero: another version this guide coversWaveshare 7.3 inch Full-Colour E-Paper Photo Frame for Raspberry Pi Zero₹9,550
ESP32-WROOM-32 38-pin development board: for Wi-Fi logging and dashboardsESP32-WROOM-32 38-Pin Development Board₹389
Raspberry Pi Zero 2 W: for the HAT and photo frameRaspberry Pi Zero 2 W with Header₹3,009Closest match, check the specs
4-channel logic level converter (BSS138): to connect 5 V and 3.3 V signals safely4-Channel Logic Level Converter (BSS138)₹20
MicroSD card module: to store images for the displayMicroSD Card Module (SPI)₹45Closest match, check the specs
Dupont jumper wires: for the connectionsDupont Jumper Wires (40 pcs)₹49Closest match, check the specs
Alternatives and when to choose them
- E-paper displays: how e-paper works and when to use it.
- SSD1306 OLED: fast, small and bright, but needs power to show anything.
- TFT displays: full-colour and fast refresh.
Common mistakes to avoid
- Choosing the wrong panel class so the screen stays blank or shows noise.
- Powering a bare panel from 5 V logic without a level shifter.
- Refreshing a colour panel every few seconds.
- Using an Uno for a large panel and running out of RAM.
Frequently asked questions
Does e-paper use power to show an image?
No. It only uses power while changing the image.
Can it show video or animation?
No. A full refresh takes seconds; partial refresh on black-and-white panels allows simple updates.
Why does the screen flash black and white?
That is the full refresh clearing the old image; it is normal.
Which library should I use?
GxEPD2 on Arduino and ESP32; Waveshare's Python library on Raspberry Pi.
Can I use it outdoors?
Yes, it is readable in sunlight, but keep it out of rain and above 0 C.
Parts for this guide
Keep learning
Sources
Written by the Geekobot team from manufacturer datasheets. Always check the datasheet for the exact part and variant you buy.

