Comparison · Intermediate · 4 min read
TFT Displays for Arduino and ESP32
ILI9341 vs ST7735 vs ST7789
By Geekobot Learning Team · Updated 24 Oct 2026
On this page
Small colour TFT and IPS displays use a driver chip that sets the resolution and the library you need: ST7735 for 1.44 to 1.8 inch 128x160 screens, ST7789 for sharp 240x240 or 240x320 IPS screens, ILI9341 for 2.4 to 3.2 inch 240x320 screens, and GC9A01 for round screens. All use SPI at 3.3 V logic. Pair them with an ESP32 or Pico and TFT_eSPI.
Key specs at a glance
- ST7735
- 128x128 or 128x160, 0.96 to 1.8 in
- ST7789
- 240x240, 240x280 or 240x320 IPS, 1.3 to 2 in
- ILI9341
- 240x320, 2.2 to 3.2 in, often with XPT2046 touch and SD slot
- GC9A01
- 240x240 round, 1.28 in
- Interface
- 4-wire SPI plus DC and RESET; backlight pin
- Logic
- 3.3 V; level shifting needed from a 5 V Arduino
Driver chips compared
| Driver | Resolution | Sizes | Panel | Notes |
|---|---|---|---|---|
| ST7735 | 128x160 / 128x128 | 0.96 to 1.8 in | TFT (narrow viewing angle) | Cheap; fine for menus |
| ST7789 | 240x240 / 240x320 | 1.3 to 2.0 in | Usually IPS | Sharp and bright; very popular with ESP32 |
| ILI9341 | 240x320 | 2.2 to 3.2 in | TFT | Often has touch and microSD on the same board |
| GC9A01 | 240x240 | 1.28 in round | IPS | Watch faces and gauges |
| ILI9488 / ST7796 | 320x480 | 3.5 to 4 in | TFT or IPS | Needs more RAM and SPI speed; ESP32-S3 recommended |
- ST7735
- Resolution:
- 128x160 / 128x128
- Sizes:
- 0.96 to 1.8 in
- Panel:
- TFT (narrow viewing angle)
- Notes:
- Cheap; fine for menus
- ST7789
- Resolution:
- 240x240 / 240x320
- Sizes:
- 1.3 to 2.0 in
- Panel:
- Usually IPS
- Notes:
- Sharp and bright; very popular with ESP32
- ILI9341
- Resolution:
- 240x320
- Sizes:
- 2.2 to 3.2 in
- Panel:
- TFT
- Notes:
- Often has touch and microSD on the same board
- GC9A01
- Resolution:
- 240x240
- Sizes:
- 1.28 in round
- Panel:
- IPS
- Notes:
- Watch faces and gauges
- ILI9488 / ST7796
- Resolution:
- 320x480
- Sizes:
- 3.5 to 4 in
- Panel:
- TFT or IPS
- Notes:
- Needs more RAM and SPI speed; ESP32-S3 recommended
Typical SPI wiring
| Display pin | Function | ESP32 (VSPI) | Raspberry Pi Pico |
|---|---|---|---|
| VCC | Power, 3.3 or 5 V (check the board) | 3V3 | 3V3 |
| GND | Ground | GND | GND |
| SCL / SCK | SPI clock | GPIO 18 | GP18 |
| SDA / MOSI | SPI data in | GPIO 23 | GP19 |
| CS | Chip select | GPIO 15 | GP17 |
| DC / RS / A0 | Data or command | GPIO 2 | GP20 |
| RES / RST | Reset | GPIO 4 | GP21 |
| BL / LED | Backlight | 3V3 or a PWM pin | 3V3 or a PWM pin |
| MISO | Read back (optional) | GPIO 19 | GP16 |
- VCC
- Function:
- Power, 3.3 or 5 V (check the board)
- ESP32 (VSPI):
- 3V3
- Raspberry Pi Pico:
- 3V3
- GND
- Function:
- Ground
- ESP32 (VSPI):
- GND
- Raspberry Pi Pico:
- GND
- SCL / SCK
- Function:
- SPI clock
- ESP32 (VSPI):
- GPIO 18
- Raspberry Pi Pico:
- GP18
- SDA / MOSI
- Function:
- SPI data in
- ESP32 (VSPI):
- GPIO 23
- Raspberry Pi Pico:
- GP19
- CS
- Function:
- Chip select
- ESP32 (VSPI):
- GPIO 15
- Raspberry Pi Pico:
- GP17
- DC / RS / A0
- Function:
- Data or command
- ESP32 (VSPI):
- GPIO 2
- Raspberry Pi Pico:
- GP20
- RES / RST
- Function:
- Reset
- ESP32 (VSPI):
- GPIO 4
- Raspberry Pi Pico:
- GP21
- BL / LED
- Function:
- Backlight
- ESP32 (VSPI):
- 3V3 or a PWM pin
- Raspberry Pi Pico:
- 3V3 or a PWM pin
- MISO
- Function:
- Read back (optional)
- ESP32 (VSPI):
- GPIO 19
- Raspberry Pi Pico:
- GP16
Which library to use
(ESP32, ESP8266, RP2040): the fastest choice. Configure your driver and pins in User_Setup.h or a file selected in User_Setup_Select.h, not in the sketch. It supports sprites for flicker-free updates and anti-aliased fonts.
with Adafruit_ST7735, Adafruit_ST7789 or Adafruit_ILI9341: works on almost any board, including the Uno, with pins set in the sketch. Slower, but simplest to start.
similar speed to TFT_eSPI, configured in code.
a full GUI library (buttons, sliders, charts) that runs on top of a display driver; best on ESP32-S3 with PSRAM.
Can you use a TFT with an Arduino Uno?
Yes, with limits. The Uno has 2 KB of RAM, while one full 240x320 frame in 16-bit colour needs about 150 KB, so it can only draw shapes and text directly, and full-screen updates are slow. Most bare display modules have 3.3 V logic: add a level shifter or 1 kΩ to 2.2 kΩ series resistors on each signal line (a common quick fix, not a guaranteed one) or buy a 5 V shield version. For anything animated, an ESP32 or Pico is a far better host.
Touch and SD card on ILI9341 boards
The common red 2.4 to 2.8 inch ILI9341 boards add an XPT2046 resistive touch controller and a microSD slot, both on the same SPI bus with their own chip-select pins (T_CS and SD_CS). Keep all unused chip-select pins HIGH. Resistive touch needs calibration and a firm press; TFT_eSPI includes a calibration sketch. Some cheap SD slots do not release the MISO line, which stops the display reading back; use a separate SPI bus or skip reading from the display.
Try it: Display memory and refresh rate calculator
Change the values and the diagram and results update as you type.
Common mistakes to avoid
- Setting pins in the sketch when TFT_eSPI reads them only from User_Setup.h.
- Driving a 3.3 V display directly from 5 V Uno pins.
- Choosing the wrong driver (ST7735 vs ST7789) because the boards look alike.
- Leaving the backlight pin unconnected and seeing a black screen.
- Redrawing the whole screen every loop instead of updating only what changed.
Frequently asked questions
What is the difference between ST7735 and ST7789?
Resolution and panel type. ST7735 drives smaller 128x160 screens; ST7789 drives sharper 240x240 or 240x320 screens, usually IPS with wide viewing angles.
Why is my TFT display showing a white screen?
Usually wrong driver selected, wrong pins, a 5 V logic problem, or missing reset wiring. Check User_Setup.h if you use TFT_eSPI.
Which TFT display is best for ESP32?
A 240x240 or 240x320 ST7789 IPS module for small sharp screens, or a 2.8 inch ILI9341 with touch for a control panel.
Can an Arduino Uno drive a 240x320 TFT?
Yes, for text, simple graphics and menus, but slowly and without a frame buffer. Use an ESP32 or Pico for animation.
Is IPS better than TFT?
IPS is a type of TFT panel with better colours and viewing angles. Ordinary TFT panels look washed out from the side.
Parts for this guide
Terms in this guide
Projects that use it
Put this into practice: 171 step-by-step builds in our project library use parts from this guide.
Keep learning
Sources
Written by the Geekobot team from manufacturer datasheets. Always check the datasheet for the exact part and variant you buy.



