Component guide · Beginner · 3 min read
Arduino Modulino Modules

Buzzer, Distance (ToF), Knob (Rotary Encoder), Latch Relay, Movement (IMU), Thermo, Pixels and Buttons
By Geekobot Learning Team · Updated 29 Oct 2026
On this page
Modulino modules are small Arduino boards that connect with Qwiic cables to the Qwiic port on the UNO R4 WiFi, Nano R4 or UNO Q, or to any board with an adapter. Each has one job: a buzzer, ToF distance sensor, rotary knob, latching relay, 6-axis IMU, temperature and humidity sensor, eight RGB pixels or three buttons. One library, Arduino_Modulino, drives them all.
Key specs at a glance
- Connection
- Qwiic (4-pin JST SH), I2C, 3.3V
- Distance
- VL53L4CD time-of-flight, up to about 1.2 m
- Movement
- LSM6DSOX 6-axis IMU
- Thermo
- HS3003 temperature and humidity
- Knob
- Rotary encoder with push
- Others
- Buzzer, 8 RGB LEDs, 3 buttons with LEDs, latching relay
Models in this guide
These are alternatives. Pick the one that fits your project; you only need one.
Option 1Arduino Modulino Buzzer Module ABX00108₹689
Option 2Arduino Modulino Distance Sensor Module ABX00102₹1,249
Option 3Arduino Modulino Knob ABX00107 – Qwiic Rotary Encoder₹919
Option 4Arduino Modulino Latch Relay ABX00138₹1,089
Option 5Arduino Modulino Movement Module ABX00101₹1,209
Option 6Arduino Modulino Thermo Sensor Module ABX00103₹869
What the Arduino Modulino Qwiic modules (Buzzer, Distance, Knob, Latch Relay, Movement, Thermo, Pixels, Buttons) is
Modulino modules are small Arduino I2C boards that connect with Qwiic cables, each with one job such as distance, motion, buttons or a buzzer.
Chain several modules with Qwiic cables; each has its own I2C address. Some modules (Buttons, Buzzer, Knob, Pixels) have a small microcontroller on board, so they answer as I2C devices too.
Modulino is part of the Arduino Plug and Make Kit. The latch relay keeps its state without power and is for low-voltage loads.
Arduino Modulino Qwiic modules (Buzzer, Distance, Knob, Latch Relay, Movement, Thermo, Pixels, Buttons) pinout
The pins on the Arduino Modulino Qwiic modules (Buzzer, Distance, Knob, Latch Relay, Movement, Thermo, Pixels, Buttons) and what each one does.
| Pin | Function |
|---|---|
| Qwiic in | 3.3V, GND, SDA, SCL |
| Qwiic out | Daisy-chain to the next module |
| Relay terminals | On the Latch Relay |
| Mounting holes | Fit the Plug and Make base |
| Address pads | On some modules |
- Qwiic in
- 3.3V, GND, SDA, SCL
- Qwiic out
- Daisy-chain to the next module
- Relay terminals
- On the Latch Relay
- Mounting holes
- Fit the Plug and Make base
- Address pads
- On some modules
Wiring the Arduino Modulino Qwiic modules (Buzzer, Distance, Knob, Latch Relay, Movement, Thermo, Pixels, Buttons)
On the UNO R4 WiFi, the Qwiic port is Wire1 in code; the library handles this.
| Arduino Modulino Qwiic modules (Buzzer, Distance, Knob, Latch Relay, Movement, Thermo, Pixels, Buttons) pin | Connection | Note |
|---|---|---|
| Module | Qwiic cable to the board's Qwiic port | Click fully home |
| Chain | Out to next module's in | Keep the chain short |
| Non-Qwiic board | SDA, SCL, 3.3V, GND jumpers | 3.3V only |
- Module
- Connection:
- Qwiic cable to the board's Qwiic port
- Note:
- Click fully home
- Chain
- Connection:
- Out to next module's in
- Note:
- Keep the chain short
- Non-Qwiic board
- Connection:
- SDA, SCL, 3.3V, GND jumpers
- Note:
- 3.3V only
Example code
Install Arduino_Modulino from the Library Manager. Names come from its examples.
#include <Modulino.h>
ModulinoDistance distance;
ModulinoPixels pixels;
void setup() {
Modulino.begin();
distance.begin();
pixels.begin();
}
void loop() {
if (distance.available()) {
int mm = distance.get();
int n = constrain(map(mm, 50, 400, 8, 0), 0, 8);
for (int i = 0; i < 8; i++)
pixels.set(i, i < n ? RED : GREEN, 20);
pixels.show();
}
}Setup and tuning
chain modules with Qwiic cables from the board's Qwiic port; no soldering or breadboard is needed.
install the Arduino Modulino library and call Modulino.begin() before using each module.
each module type has its own default I2C address. Two of the same type need an address change.
Qwiic is 3.3 V. Use the UNO R4 WiFi or Nano R4 Qwiic port, or an adapter on other boards.
keep the total Qwiic chain short, about a metre, for reliable I2C.
What you need
Shop this list9 of 9 found in our store · ₹8,365
Arduino Modulino Buzzer Module ABX00108: the part this guide coversArduino Modulino Buzzer Module ABX00108₹689
Arduino Modulino Distance Sensor Module ABX00102: another version this guide coversArduino Modulino Distance Sensor Module ABX00102₹1,249
Arduino Modulino Knob ABX00107 – Qwiic Rotary Encoder: another version this guide coversArduino Modulino Knob ABX00107 – Qwiic Rotary Encoder₹919
Arduino Modulino Latch Relay ABX00138: another version this guide coversArduino Modulino Latch Relay ABX00138₹1,089
Arduino Modulino Movement Module ABX00101: another version this guide coversArduino Modulino Movement Module ABX00101₹1,209
Arduino Modulino Thermo Sensor Module ABX00103: another version this guide coversArduino Modulino Thermo Sensor Module ABX00103₹869
Arduino NODE09 NEOP Pixels Module ABX00109: another version this guide coversArduino NODE09 NEOP Pixels Module ABX00109₹1,279
Arduino NODE10 BUTTON Module ABX00110: another version this guide coversArduino NODE10 BUTTON Module ABX00110₹899
USB-C cable: for power and programmingUSB-C Power Cable with On/Off Switch for Raspberry Pi 4₹163
Alternatives and when to choose them
- VL53L4CX ToF: breakout version.
- LSM6DSO IMU: similar IMU.
- KY-040 encoder: simple knob.
Common mistakes to avoid
- Chaining very long Qwiic cables, which makes I2C unreliable.
- Using two identical modules without changing an address.
- Wiring a module to 5 V I2C without level shifting.
- Forgetting to call Modulino.begin() before reading.
Frequently asked questions
Which boards can use Modulino modules?
Any board with a Qwiic port, such as the UNO R4 WiFi, Nano R4 and UNO Q, or other boards with a Qwiic adapter.
Can I use two of the same Modulino?
Yes, after changing one module's I2C address as the library describes.
Are Modulino modules 5 V?
No. They run on 3.3 V Qwiic. The UNO R4 Qwiic port already provides 3.3 V.
How far can the Distance module measure?
It uses the VL53L4CD time-of-flight sensor and reads up to about 1.2 m.
Do they work with Qwiic boards from SparkFun?
Yes. They use the same Qwiic connector and I2C, so they mix with other Qwiic boards.
Parts for this guide
Keep learning
Sources
Written by the Geekobot team from manufacturer datasheets. Always check the datasheet for the exact part and variant you buy.

