Buying guide · Intermediate · 3 min read
Bluetooth LE Modules
HM-10, nRF52840, JDY and EByte Compared
By Geekobot Learning Team · Updated 29 Oct 2026
On this page
Bluetooth Low Energy (BLE) modules come in two types: serial modules such as the HM-10, HC-08 and JDY-29 that pass UART data to a phone with no firmware work, and programmable modules such as the nRF52840 that run your own code. iPhones only connect to BLE, not to classic Bluetooth SPP modules like the HC-05, so choose BLE if iOS support matters.
Key specs at a glance
- Serial BLE modules
- HM-10 (CC2541), HC-08, HC-42, JDY-29/JDY-23: UART in, BLE out
- Programmable BLE SoCs
- nRF52832, nRF52840 (BLE 5, Thread, Zigbee, USB), EByte E73 and Holyiot modules
- Bluetooth versions
- BLE 4.0 to 5.4; 5.x adds longer range and faster modes
- Supply
- Usually 1.8 to 3.6 V on the chip; modules sold at 3.3 or 5 V
- Logic level
- 3.3 V on most; a 5 V Arduino TX needs a divider
- Range
- Typically 10 to 50 m indoors
Classic Bluetooth vs BLE
Classic Bluetooth (HC-05, HC-06, JDY-31) streams like a wireless serial cable and uses more power. BLE sends small packets, sleeps between them and runs for months on a coin cell. The key trap: iOS apps cannot open a classic Bluetooth serial link. If you want your project to work with an iPhone, you need a BLE module. Android supports both. Read HC-05 for the classic option.
Which module should you use?
Choose by how much firmware you want to write.
| Type | Examples | How you use it | Best for |
|---|---|---|---|
| Serial BLE modules | HM-10, HC-08, HC-42, JDY-29 | Send text over UART; a phone app talks to it | Quick Arduino-to-phone links, remote controls |
| Programmable BLE modules | nRF52832, nRF52840, EByte E73, Holyiot | Write your own firmware (Arduino, Zephyr, nRF Connect SDK) | Low-power sensors, beacons, wearables |
| Wi-Fi + BLE SoC | ESP32, ESP32-C3, Ai-WB2 | Program the chip directly | Projects that also need Wi-Fi |
| Beacon modules | iBeacon and Eddystone modules | Broadcast a fixed ID | Indoor location, asset tags |
- Serial BLE modules
- Examples:
- HM-10, HC-08, HC-42, JDY-29
- How you use it:
- Send text over UART; a phone app talks to it
- Best for:
- Quick Arduino-to-phone links, remote controls
- Programmable BLE modules
- Examples:
- nRF52832, nRF52840, EByte E73, Holyiot
- How you use it:
- Write your own firmware (Arduino, Zephyr, nRF Connect SDK)
- Best for:
- Low-power sensors, beacons, wearables
- Wi-Fi + BLE SoC
- Examples:
- ESP32, ESP32-C3, Ai-WB2
- How you use it:
- Program the chip directly
- Best for:
- Projects that also need Wi-Fi
- Beacon modules
- Examples:
- iBeacon and Eddystone modules
- How you use it:
- Broadcast a fixed ID
- Best for:
- Indoor location, asset tags
Wiring a serial BLE module to Arduino
Connect VCC to 3.3 V (or 5 V if the board has a regulator), GND to GND, module TX to Arduino pin 2 and module RX to pin 3 through a voltage divider (for example 1 kΩ to the pin and 2 kΩ to GND), because the module's RX is a 3.3 V input. This sketch passes text both ways so you can use AT commands.
#include <SoftwareSerial.h>
SoftwareSerial ble(2, 3); // RX, TX on the Arduino
void setup() {
Serial.begin(9600);
ble.begin(9600); // HM-10 default baud rate
Serial.println("Type AT commands (set 'No line ending')");
}
void loop() {
if (ble.available()) Serial.write(ble.read());
if (Serial.available()) ble.write(Serial.read());
}
// Try: AT -> OK AT+NAMEmyble -> OKsetName AT+VERSION?Testing and connecting
Use a free app such as nRF Connect or LightBlue to scan, connect and send data. Serial BLE modules expose a GATT characteristic (often FFE1 on HM-10-style parts) that the app writes to and reads from. The module's name shows up during scanning because it is advertising. See ESP32 if you want to write BLE firmware directly.
Range, power and security
- Antenna placement matters: keep the antenna end of a PCB module away from metal and batteries.
- Sleep modes drop current from milliamps to microamps; read the module's AT command list.
- Default PINs are weak. If you control hardware, add pairing or an application-level check.
Try it: Voltage divider calculator
Change the values and the diagram and results update as you type.
Common mistakes to avoid
- Buying an HC-05 for an iPhone project.
- Connecting a 5 V Arduino TX straight to the module RX.
- Sending AT commands with line endings an HM-10 does not expect.
- Placing the antenna against a metal case.
- Leaving default names and no authentication on a device that controls something real.
Frequently asked questions
Does the HM-10 work with iPhone?
Yes, it is BLE, so iOS apps can connect to it.
HM-10 or HC-08?
Both are serial BLE modules. HC-08 and JDY parts are newer and often cheaper; check the AT command set before you rely on a library.
Can the ESP32 replace a BLE module?
Yes. The ESP32 has BLE built in, so you can write your own services.
What does nRF52840 add?
BLE 5 with long range, a USB port, Thread and Zigbee support and very low power.
How far will BLE reach?
10 to 50 m indoors, more in open air with BLE 5 long-range mode and a good antenna.
Can two BLE modules talk to each other?
Yes, if one acts as central and the other as peripheral. Many serial modules support only the peripheral role.
Parts for this guide
Calculators
Terms in this guide
Keep learning
Sources
- Bluetooth SIG: Core Specification
- Nordic Semiconductor nRF52840 product specification
- TI CC2541 datasheet and HM-10 AT command set
Written by the Geekobot team from manufacturer datasheets. Always check the datasheet for the exact part and variant you buy.




