Component guide · Intermediate · 3 min read
Bosch BMI088 (Chip and Seeed Grove)

and BMI085 High-Performance 6-Axis IMUs for Drones and Robots
By Geekobot Learning Team · Updated 29 Oct 2026
On this page
The Bosch BMI088 is a 6-axis IMU built to cope with vibration, which is why many flight controllers use it. It has a ±24 g accelerometer and a ±2000 °/s gyroscope that work as two separate devices on the bus, each with its own address. The BMI085 is a similar part for AR and robotics, and the Seeed Grove board makes the BMI088 plug and play.
Key specs at a glance
- Accelerometer
- ±3 to ±24 g (BMI088), ±2 to ±16 g (BMI085)
- Gyroscope
- ±125 to ±2000 °/s
- Interface
- I2C or SPI; accel and gyro have separate addresses
- Addresses
- Accel 0x18 or 0x19, gyro 0x68 or 0x69
- Supply
- 2.4 to 3.6 V (Grove 3.3 or 5 V)
- Strength
- Vibration robust, low drift
Models in this guide
These are alternatives. Pick the one that fits your project; you only need one.
Option 1Bosch Sensortec BMI088 LGA-16 High-Precision Accelerometer Gyroscope IMU₹979
Option 2Seeed Studio BMI088 Grove 6-Axis Accelerometer & Gyroscope Module – I2C Interface₹4,409
Option 3Bosch BMI085 High-Precision 6-Axis IMU Sensor, 16-bit Accel & Gyro, ±16g, ±2000 dps, 2000Hz, Low Noise, I2C/SPI₹1,529
What the BMI088 and BMI085 high-performance IMUs is
The Bosch BMI088 and BMI085 are 6-axis IMUs built to reject vibration, so drones and robots get clean accelerometer and gyro data even with motors running.
Treat the BMI088 as two sensors: an accelerometer and a gyroscope with separate addresses and settings. An I2C scan shows both.
Its high accelerometer range and vibration tolerance suit drones, rockets and robots that bump.
BMI088 and BMI085 high-performance IMUs pinout
The pins on the BMI088 and BMI085 high-performance IMUs and what each one does.
| Pin | Function |
|---|---|
| VCC | Supply |
| GND | Ground |
| SCL / SDA | I2C |
| CSB1 / CSB2 | SPI selects for accel and gyro |
| INT1 to INT4 | Interrupts |
- VCC
- Supply
- GND
- Ground
- SCL / SDA
- I2C
- CSB1 / CSB2
- SPI selects for accel and gyro
- INT1 to INT4
- Interrupts
Wiring the BMI088 and BMI085 high-performance IMUs
Modules with a regulator run from 3.3 V or 5 V. Bare chips (LGA or QFN parts) are 1.8 to 3.6 V only: mount them on a breakout and use a level shifter with 5 V boards.
| BMI088 and BMI085 high-performance IMUs pin | Arduino Uno | ESP32 |
|---|---|---|
| VCC | 5V (or 3.3V) | 3V3 |
| GND | GND | GND |
| SDA | A4 | GPIO 21 |
| SCL | A5 | GPIO 22 |
- VCC
- Arduino Uno:
- 5V (or 3.3V)
- ESP32:
- 3V3
- GND
- Arduino Uno:
- GND
- ESP32:
- GND
- SDA
- Arduino Uno:
- A4
- ESP32:
- GPIO 21
- SCL
- Arduino Uno:
- A5
- ESP32:
- GPIO 22
Example code
Bolder Flight's Bmi088 library is another good choice, with SPI support.
#include "BMI088.h"
BMI088 bmi088(BMI088_ACC_ADDRESS, BMI088_GYRO_ADDRESS);
void setup() {
Serial.begin(115200);
Wire.begin();
while (!bmi088.isConnection()) { Serial.println("BMI088 not found"); delay(1000); }
bmi088.initialize();
}
void loop() {
float ax, ay, az, gx, gy, gz;
bmi088.getAcceleration(&ax, &ay, &az); // mg
bmi088.getGyroscope(&gx, &gy, &gz); // dps
Serial.printf("acc mg %.0f %.0f %.0f gyro dps %.1f %.1f %.1f\n", ax, ay, az, gx, gy, gz);
delay(100);
}Setup and tuning
the accelerometer and gyro have separate I2C addresses or SPI chip selects; set both in the library.
SPI gives faster, more reliable data at high sample rates.
run at 3.3 V; the Grove module adds level shifting for 5 V boards.
mount close to the centre of gravity with soft damping.
set output data rate and bandwidth to match your control loop.
What you need
Shop this list5 of 7 found in our store · ₹7,475
Bosch Sensortec BMI088 LGA-16 High-Precision Accelerometer Gyroscope IMU: the part this guide coversBosch Sensortec BMI088 LGA-16 High-Precision Accelerometer Gyroscope IMU₹979
Seeed Studio Studio BMI088 Grove 6-Axis Accelerometer & Gyroscope Module – I2C Interface: another version this guide coversSeeed Studio BMI088 Grove 6-Axis Accelerometer & Gyroscope Module – I2C Interface₹4,409
Bosch BMI085 High-Precision 6-Axis IMU Sensor, 16-bit Accel & Gyro, ±16g, ±2000 dps, 2000Hz, Low Noise, I2C/SPI: another version this guide coversBosch BMI085 High-Precision 6-Axis IMU Sensor, 16-bit Accel & Gyro, ±16g, ±2000 dps, 2000Hz, Low Noise, I2C/SPI₹1,529
ESP32-WROOM-32 38-pin development board: for Wi-Fi logging and dashboardsESP32-WROOM-32 38-Pin Development Board₹389- Uno R3 development board: the controller used in the wiring tableFind this part
GY-521 MPU6050 6-axis module: the classic low-cost IMUGY-521 MPU6050 6-Axis Gyro and Accelerometer Module₹169Closest match, check the specs- BNO085 IMU module: gives ready-made orientationFind this part
Alternatives and when to choose them
- ICM-42688-P: another flight-controller IMU.
- BMI270: low-power Bosch IMU.
- Flight controllers: boards that already include IMUs.
Common mistakes to avoid
- Setting only one of the two I2C addresses.
- Running the bare chip at 5 V.
- Hard-mounting it on a vibrating frame.
- Reading at a rate far below the control loop.
Frequently asked questions
Why is the BMI088 used in drones?
Its design rejects motor vibration better than consumer IMUs, giving cleaner data for flight control.
Does the BMI088 have a magnetometer?
No. It is a 6-axis IMU; add a separate magnetometer for heading.
Why does only the gyro respond?
The accelerometer needs its own address or chip select and a power-up command; check both are set.
Can I use it with Arduino?
Yes, with Bosch or Seeed libraries over I2C or SPI.
BMI085 or BMI088?
They are very similar; the BMI085 is a smaller variant with similar performance.
Parts for this guide
Keep learning
Sources
Written by the Geekobot team from manufacturer datasheets. Always check the datasheet for the exact part and variant you buy.


