Comparison · Intermediate · 3 min read
Flight Controllers
F4 vs F7 vs H7, Betaflight, INAV and ArduPilot
By Geekobot Learning Team · Updated 24 Oct 2026
On this page
A flight controller reads its gyro thousands of times a second and adjusts each motor to keep the craft stable and follow your sticks. For freestyle and racing quads, an F405 or F722 board running Betaflight is the standard. For GPS missions, return-to-home and fixed-wing, use INAV on an F4 or F7 board, or ArduPilot and PX4 on an H7 board. Count UARTs before buying: receiver, video, GPS and telemetry each need one.
Key specs at a glance
- F4 (STM32F405 / F411)
- Budget and mainstream; F411 has few UARTs
- F7 (STM32F722 / F745)
- More UARTs and headroom
- H7 (STM32H743)
- Fastest; needed for full ArduPilot features
- Gyros
- ICM-42688-P, BMI270, MPU6000
- Mounting
- 30.5x30.5, 20x20 and 25.5x25.5 mm (whoop)
- Firmware
- Betaflight, INAV, ArduPilot, PX4
Which firmware fits your flying?
| Firmware | Best for | Strengths | Typical board |
|---|---|---|---|
| Betaflight | FPV freestyle and racing | Best stick feel, filtering, huge community | F405, F722 |
| INAV | GPS FPV, fixed-wing, long range | Return-to-home, position hold, waypoints | F405, F722, H743 |
| ArduPilot | Autonomous missions, survey, rovers and boats | Mature mission planning, many vehicle types | H743 and Pixhawk-class boards |
| PX4 | Research, companion-computer and ROS 2 projects | Modular, widely used in industry and universities | Pixhawk-class boards |
- Betaflight
- Best for:
- FPV freestyle and racing
- Strengths:
- Best stick feel, filtering, huge community
- Typical board:
- F405, F722
- INAV
- Best for:
- GPS FPV, fixed-wing, long range
- Strengths:
- Return-to-home, position hold, waypoints
- Typical board:
- F405, F722, H743
- ArduPilot
- Best for:
- Autonomous missions, survey, rovers and boats
- Strengths:
- Mature mission planning, many vehicle types
- Typical board:
- H743 and Pixhawk-class boards
- PX4
- Best for:
- Research, companion-computer and ROS 2 projects
- Strengths:
- Modular, widely used in industry and universities
- Typical board:
- Pixhawk-class boards
Hardware features that matter
each serial device (receiver, digital video, GPS, ESC telemetry, Bluetooth) needs one. F411 boards have only two or three; F405 and F722 boards usually have five or six.
most boards now use ICM-42688-P or BMI270 chips. Mount the board on soft grommets to reduce vibration.
onboard flash for flight logs helps tuning.
analog boards carry an AT7456E chip for on-screen text; digital systems (DJI, Walksnail, HDZero) use MSP DisplayPort over a UART instead.
look for a 5 V and a 9 or 10 V regulator for the receiver, camera and video transmitter.
a matching flight controller and 4-in-1 ESC of the same size simplify wiring.
First setup checklist
- 1Flash the latest stable firmware with the Betaflight, INAV or Mission Planner configurator; pick the target that matches your board name exactly.
- 2Set board orientation and calibrate the accelerometer on a level surface.
- 3Configure ports: receiver protocol (CRSF for ExpressLRS, SBUS or IBUS for FlySky) on the right UART.
- 4Check the receiver tab: sticks move the right channels in the right direction.
- 5With props off, check motor order and spin direction in the motors tab, and reverse motors in ESC firmware if needed.
- 6Set up arming on a switch, failsafe, and modes (angle, acro, GPS rescue).
Can you build a flight controller with an Arduino or ESP32?
Yes, as a learning project: there are open projects for ESP32 and STM32 'Blue Pill' boards with an MPU6050 gyro. They teach PID control well, but they are not as safe or reliable as a proper flight controller with tuned filters, failsafes and good gyros. For anything that flies near people, use proven hardware and firmware.
Common mistakes to avoid
- Buying an F411 board and running out of UARTs for GPS and video.
- Flashing the wrong target and bricking the configuration (reflash with the correct one).
- Testing motor direction with props on.
- Hard-mounting the board so vibration ruins the gyro data.
- Ignoring failsafe setup.
Frequently asked questions
Which flight controller is best for beginners?
An F405 or F722 board running Betaflight, ideally as a stack with a matching 4-in-1 ESC. They are well documented and widely supported.
What is the difference between F4, F7 and H7?
The STM32 processor family. F7 and H7 are faster and usually have more UARTs and memory; H7 boards are needed for the full ArduPilot feature set.
Betaflight or INAV?
Betaflight for freestyle and racing. INAV if you want GPS features such as return-to-home, position hold and waypoint missions, or for fixed-wing planes.
How many UARTs do I need?
One each for the receiver, digital video or VTX control, GPS and any telemetry. Most builds need three to five.
Can a drone flight controller run ArduPilot?
Many F4, F7 and H7 boards are supported, but newer ArduPilot releases need more memory, so H7 boards are the safest choice.
Parts for this guide
Terms in this guide
Projects that use it
Put this into practice: 1 step-by-step build in our project library uses parts from this guide.
Keep learning
Sources
- Betaflight and INAV documentation
- ArduPilot and PX4 hardware support lists
- STMicroelectronics STM32F4, F7 and H7 datasheets
Written by the Geekobot team from manufacturer datasheets. Always check the datasheet for the exact part and variant you buy.




