Concept explainer · Beginner · 4 min read
Drone Parts Explained
Motors, ESCs, Flight Controller, Props and Battery
By Geekobot Learning Team · Updated 24 Oct 2026
On this page
A quadcopter has a frame, four brushless motors spun by four ESCs (electronic speed controllers), a flight controller that reads its gyro and balances the craft, propellers, a LiPo battery, a radio receiver for your transmitter, and optionally an FPV camera and video transmitter. Match motor KV, prop size and battery cell count to each other, or the drone will overheat or fail to lift.
Key specs at a glance
- Frame
- Size by prop: 5-inch freestyle (210 to 230 mm), 3-inch, 7-inch long range
- Motors
- Brushless, e.g. 2207 2400 KV for 5-inch on 4S to 6S
- ESC
- 4-in-1 board, 30 to 60 A per motor, BLHeli_S/32 or AM32
- Flight controller
- F4/F7/H7 processor, Betaflight or INAV firmware
- Battery
- LiPo 4S to 6S, 1300 to 1500 mAh, 75 to 100 C for 5-inch
- Radio
- ELRS or Crossfire receiver, 2.4 GHz or 900 MHz
- FPV
- Analog 5.8 GHz or digital (DJI, HDZero, Walksnail)
A shorted, over-charged or damaged lithium cell can get very hot and catch fire. Use a protection board or BMS, never short the terminals, charge on a non-flammable surface and do not leave a charging pack alone. Throw away cells that are swollen or dented.
What each part does
| Part | Job | What to look at |
|---|---|---|
| Frame | Holds everything, absorbs crashes | Carbon fibre thickness, arm size, prop size |
| Brushless motor | Spins the prop | Stator size (2207 = 22 mm wide, 7 mm tall), KV (RPM per volt), shaft size |
| ESC | Turns the FC's throttle signal into 3-phase motor power | Current rating with margin, DShot support, firmware |
| Flight controller (FC) | Reads gyro and accelerometer, mixes your sticks and keeps the craft level | Processor (F4/F7/H7), gyro type, UARTs, mounting (30.5 or 20 mm) |
| Propellers | Produce thrust | Diameter, pitch, blade count, CW/CCW pairs |
| LiPo battery | Supplies tens of amps | Cells (S), mAh, C rating, XT60 connector |
| Receiver | Gets your transmitter's commands | Protocol (ELRS, Crossfire, FrSky), range |
| FPV camera and VTX | Sends live video to goggles | Analog or digital, VTX power, antennas |
| GPS (optional) | Position hold, return-to-home | M8N/M10 modules; needed for INAV missions |
- Frame
- Job:
- Holds everything, absorbs crashes
- What to look at:
- Carbon fibre thickness, arm size, prop size
- Brushless motor
- Job:
- Spins the prop
- What to look at:
- Stator size (2207 = 22 mm wide, 7 mm tall), KV (RPM per volt), shaft size
- ESC
- Job:
- Turns the FC's throttle signal into 3-phase motor power
- What to look at:
- Current rating with margin, DShot support, firmware
- Flight controller (FC)
- Job:
- Reads gyro and accelerometer, mixes your sticks and keeps the craft level
- What to look at:
- Processor (F4/F7/H7), gyro type, UARTs, mounting (30.5 or 20 mm)
- Propellers
- Job:
- Produce thrust
- What to look at:
- Diameter, pitch, blade count, CW/CCW pairs
- LiPo battery
- Job:
- Supplies tens of amps
- What to look at:
- Cells (S), mAh, C rating, XT60 connector
- Receiver
- Job:
- Gets your transmitter's commands
- What to look at:
- Protocol (ELRS, Crossfire, FrSky), range
- FPV camera and VTX
- Job:
- Sends live video to goggles
- What to look at:
- Analog or digital, VTX power, antennas
- GPS (optional)
- Job:
- Position hold, return-to-home
- What to look at:
- M8N/M10 modules; needed for INAV missions
Matching motors, props and battery
A 2400 KV motor on 4S (16.8 V full) spins about 40,000 RPM; on 6S use lower KV (1700 to 1900) for the same prop.
5-inch: 1700 to 2600 KV; 7-inch: 1300 to 1700 KV; 3-inch: 3000+ KV. See BLDC motors for how brushless motors differ from brushed ones.
Check the motor's thrust table for current at full throttle with your prop.
A 1500 mAh 100 C pack can deliver 150 A, enough for four motors drawing 30 A each. See lithium batteries.
A typical 5-inch FPV build list
Shop this list8 of 9 found in our store · ₹32,059
5-inch carbon frame (220 mm wheelbase)ReadyToSky Mark4 5-Inch 225mm Carbon Fiber FPV Frame₹2,409Closest match, check the specs
4 x 2207 or 2306 motors, 1750 to 1950 KV for 6SAxisFlying 2207 Brushless Motor 1960KV₹2,859Closest match, check the specs
4-in-1 ESC, 45 to 60 A, 30.5 mm mountSpeedyBee BL32 50A 4-in-1 ESC₹5,320Closest match, check the specs
F7 or H7 flight controller with a modern gyroT-Motor F7 Flight Controller F7₹9,019Closest match, check the specs
5.1-inch tri-blade props (2 CW, 2 CCW)DC Motor Fan Blade (Toy Propeller)₹8Closest match, check the specs- 6S 1100 to 1300 mAh LiPo (or 4S 1500 mAh), XT60Find this part
ELRS receiver and matching transmitter moduleSpeedyBee Nano 915M ExpressLRS ELRS Receiver₹1,069Closest match, check the specs
FPV camera, VTX and goggles (analog to start, digital for quality)RunCam Robin 3 FPV Camera₹2,049Closest match, check the specs
Props guards for indoor practice, a smoke stopper for first power-up, and a LiPo charger with storage modeAxisFlying Cineon C35/C30 Prop Guards (2pcs) – Clear Gray₹749Closest match, check the specs
How a quadcopter stays up
Two motors spin clockwise and two anticlockwise so their torques cancel. The flight controller reads the gyro hundreds of times per second and adjusts each motor's speed: more thrust on the back motors tilts the craft forward; speeding up the CW pair yaws it. Your sticks set the desired rates; the PID controller in Betaflight does the balancing.
Before your first flight
Practise in a simulator (Liftoff, Velocidrone or the free FPV Freerider) with the same transmitter. Check local regulations: in India, drones over 250 g need registration on Digital Sky and a Remote Pilot Certificate for many uses, and no-fly zones apply near airports. Fly first without props to check motor directions, then with prop guards in an open field.
Try it: Battery life calculator
Change the values and the diagram and results update as you type.
Common mistakes to avoid
- Pairing high-KV motors with a 6S battery and burning them out.
- Installing props on the wrong motors (CW/CCW) so the drone flips on take-off.
- Plugging in a battery for the first time without a smoke stopper.
- Under-rating the ESC and getting desyncs or fires.
- Storing LiPos fully charged; keep them at storage voltage (3.8 V per cell).
Frequently asked questions
What are the main parts of a drone?
Frame, four brushless motors, four ESCs (usually one 4-in-1 board), flight controller, propellers, LiPo battery, radio receiver, and for FPV a camera and video transmitter.
What does KV mean on a drone motor?
RPM per volt with no load. A 2400 KV motor on a 14.8 V 4S pack spins about 35,500 RPM. Higher KV suits smaller props and lower voltage.
What size ESC do I need?
Rate it 20 to 30% above the motor's maximum current with your prop and battery: typically 35 to 60 A for 5-inch quads.
Which battery should I use for a 5-inch drone?
A 4S 1300 to 1500 mAh or 6S 1000 to 1300 mAh LiPo with a 75 C or higher rating and an XT60 connector.
Can I build a drone with an Arduino?
You can learn control theory with an Arduino and MPU6050, but for a flying drone use a Betaflight or INAV flight controller: it is cheaper, safer and already tuned.
Parts for this guide
Calculators
Terms in this guide
Keep learning
Sources
Written by the Geekobot team from manufacturer datasheets. Always check the datasheet for the exact part and variant you buy.



