Build a 3-inch FPV quad with DJI O3 digital HD video
A small, quiet 3-inch quad that records and streams clear HD video through a DJI O3 air unit.
Shop by category
Shop all componentsThis build takes you from a bag of parts to a tuned 5-inch freestyle quad. A SpeedyBee F405 flight controller and 50 A 4-in-1 ESC stack sits in a Mark4-style 225 mm carbon frame, four 2306 motors swing 5-inch tri-blade props, an ExpressLRS receiver links you to the radio, and an analog camera and video transmitter send live video to box goggles. Every part is a standard size, so you can repair or upgrade it piece by piece.
Take the propellers off whenever the drone is on the bench and connected to a computer or battery.
LiPo batteries can catch fire if punctured, over-discharged or charged without balance leads. Charge on a fireproof surface, never leave them charging unattended and store them at storage voltage (about 3.8 V per cell).
Before you fly, read the DGCA Drone Rules 2021 and check the Digital Sky airspace map: fly only in green zones, below 120 m, in sight, and away from people, roads and airports.
Tick anything you already have and the total updates.
ESC distribution board if you use four single ESCs instead of a 4-in-1
225 mm carbon frame for 5-inch props
F405 flight controller and 50 A 4-in-1 ESC in one 30x30 stack
2306 2500KV motors suit 5-inch props on a 4S pack
5-inch tri-blade props, 2 CW + 2 CCW per set
2.4 GHz ExpressLRS receiver, wired to a flight controller UART
Radio with a built-in 2.4 GHz ELRS transmitter
5.8 GHz analog video transmitter, 25 to 400 mW switchable
Circular-polarised 5.8 GHz antenna (RHCP); match its connector to the VTX or use an adapter
Limits current on first power-up so a short cannot burn the stack
Soft-mounts the stack to cut gyro noise
Optional: directional 2.4 GHz antenna for radios with an external ELRS module bay
Follow the colours: red is power, dark grey is ground, blue is a signal.
Runs on a 4S LiPo (about 1300 to 1500 mAh, 100C class) with an XT60 plug, bought separately. Always power up the first time through the smoke stopper with props off.
betaflight-cli.txt# Betaflight CLI, after flashing the right target for your board
set serialrx_provider = CRSF
set motor_pwm_protocol = DSHOT600
set failsafe_procedure = DROP
set vbat_max_cell_voltage = 430
set vbat_min_cell_voltage = 330
save
Motor order or direction is wrong, or props are on the wrong motors. Recheck in the Motors tab with props off, and match the Betaflight motor diagram.
Check TX and RX are crossed, Serial RX is on for that UART, the provider is CRSF and the receiver and radio use the same ELRS binding phrase and version.
Check the antenna is screwed on before powering the VTX, the goggles and VTX are on the same channel, and the antenna sits clear of carbon plates.
Balance the props, check the motor bells for play and soft-mount the FC; worn props are the most common cause.
The stack takes 3 to 6S, but 2500KV motors are made for 4S. For 6S choose motors around 1700 to 1900KV.
Read the DGCA Drone Rules 2021 for your drone's weight class, and check the Digital Sky map before every flight.
Analog is cheap, light and has low latency; digital HD looks far better. See the 3-inch digital HD project for that route.
Use a 4S LiPo with an XT60 plug and a balance charger; they are not part of this parts list.
19 parts: ESC Connection Distribution Board, ReadyToSky Mark4 5-Inch 225mm Carbon Fiber FPV Frame, SpeedyBee SB-F4V3-50-STACK Flight Controller & 50A 4-in-1 ESC Stack, 4 × DYS SUN FUN SF2306 2500KV 4-5S Brushless Motor – 1CW M5 Nut, 2 × Foxeer Dalprop Cyclone Triblade T5126 Propeller 2 Pair CW+CCW – Teal, SpeedyBee Nano 2.4G ExpressLRS ELRS Receiver, BetaFPV LiteRadio 3 Radio Transmitter (ELRS), RunCam Nano 650TVL FPV Camera, XF5806_V2 5.8GHz 40CH 25/100/200/400mW Switchable FPV VTX Transmitter, ReadyToSky Pagoda 2 Antenna 5.8GHz with Cover – RP-SMA Male RHCP, plus 9 more. Tools: 24 in 1 Precision Screwdriver Set. On this page you can tick the parts you already have and add only the rest to your cart.
It is a advanced project and takes about 2 days. The build on this page has 9 steps.
No. This page has the complete, tested code (betaflight-cli.txt).
About ₹50,694 for the parts at the prices on this page, plus tools if you do not have them. Quantity price breaks lower the cost when you build several.
How an FC and 4-in-1 ESC stack, motors and props work together; Soldering high-current XT60 and motor leads; Setting up Betaflight: ports, receiver, modes, failsafe and motor direction; Choosing VTX channels and power.
Take the propellers off whenever the drone is on the bench and connected to a computer or battery. LiPo batteries can catch fire if punctured, over-discharged or charged without balance leads. Charge on a fireproof surface, never leave them charging unattended and store them at storage voltage (about 3.8 V per cell). Before you fly, read the DGCA Drone Rules 2021 and check the Digital Sky airspace map: fly only in green zones, below 120 m, in sight, and away from people, roads and airports.
Ideas that reuse this build: Build a 3-inch quad with digital HD video and Build a GPS mapping quad on Pixhawk. They are listed under Take it further on this page.
A small, quiet 3-inch quad that records and streams clear HD video through a DJI O3 air unit.
A 450 mm quad that holds position on GPS, flies waypoint missions and can drop a small payload.
Learning project. Check every circuit and the datasheet of each part before you power it up.