Build a 5-inch FPV freestyle quad (analog video, ELRS)
A complete 5-inch freestyle drone: carbon frame, F405 stack, 2306 motors, ELRS radio link and analog goggles.
Shop by category
Shop all componentsA 3-inch quad is easier to fly near trees and parks than a 5-inch, and with a DJI O3 air unit it streams sharp digital video to the goggles and records 4K on board. Here a separate F405 flight controller and 35 A 4-in-1 ESC sit in a 150 mm frame with 1404 motors. You will also learn how a separate FC and ESC differ from an all-in-one stack.
Take the propellers off whenever the drone is on the bench and connected to a computer or battery.
LiPo batteries can catch fire if punctured, over-discharged or charged without balance leads. Charge on a fireproof surface, never leave them charging unattended and store them at storage voltage (about 3.8 V per cell).
Before you fly, read the DGCA Drone Rules 2021 and check the Digital Sky airspace map: fly only in green zones, below 120 m, in sight, and away from people, roads and airports.
Tick anything you already have and the total updates.
150 mm carbon frame for 3-inch props
Betaflight flight controller (F405, OSD)
1404 motors for 3-inch props on 4S (counter-clockwise thread)
The same motor with the clockwise thread
3-inch tri-blade props
Coax cable of the right length for a small frame
DJI goggles that work with the O3 air unit
2.4 GHz ELRS receiver (CRSF)
Only if you build a 3.5-inch cinewhoop with 90 mm ducts instead of this frame
Follow the colours: red is power, dark grey is ground, blue is a signal.
4S LiPo, about 650 to 850 mAh, bought separately. The O3 gets hot: never power it for long without airflow.
betaflight-cli.txt# Betaflight 4.4+ with a DJI O3 on an MSP UART
set osd_displayport_device = MSP
set displayport_msp_serial = 1 # the UART index used by the O3 (UART2 = 1)
set serialrx_provider = CRSF
save
Set the O3 UART to MSP in Ports, set the OSD to HD and turn on Custom OSD in the goggles menu.
It overheats without airflow. Power it only briefly with props off, or point a fan at it.
Check the harness pin order between FC and ESC; mismatched pins are the most common fault with separate boards.
Yes, it takes a wide input range, but this ESC is 2 to 5S, so stay on 4S.
If one fails you replace only that board, and you can mix brands. A stack saves wiring time.
No. They are only for a cinewhoop frame with 90 mm ducts.
13 parts: ReadyToSky APEX 3-inch 150mm Carbon Fiber FPV Frame Kit, Mamba F405 Flight Controller Betaflight STM32, 35A V2.1 2-5S 4-in-1 BLHeli_32 Brushless FPV ESC, 2 × HappyModel EX1404 KV3500 Brushless Motor (CCW), 2 × HappyModel EX1404 3500KV Brushless Motor (CW), Foxeer DalProp Cyclone Triblade T3018 Propeller 4 Pair CW+CCW – Crystal Red, DJI O3 Air Unit, AxisFlying Digital Coaxial Cable for DJI O3 Air Unit 170mm, DJI Goggles Integra – Integrated Battery Strap & Foam Padding, WeAct Studio ELRS 2.4G 6CH PWM/CRSF Receiver – Standard Set, plus 3 more. Tools: 24 in 1 Precision Screwdriver Set. On this page you can tick the parts you already have and add only the rest to your cart.
It is a advanced project and takes about 2 days. The build on this page has 6 steps.
No. This page has the complete, tested code (betaflight-cli.txt).
About ₹1,08,720 for the parts at the prices on this page, plus tools if you do not have them. Quantity price breaks lower the cost when you build several.
Pairing a digital HD air unit with goggles; Separate FC and ESC versus a matched stack; Betaflight OSD over the DJI MSP DisplayPort; Choosing motor KV for prop size and cell count.
Take the propellers off whenever the drone is on the bench and connected to a computer or battery. LiPo batteries can catch fire if punctured, over-discharged or charged without balance leads. Charge on a fireproof surface, never leave them charging unattended and store them at storage voltage (about 3.8 V per cell). Before you fly, read the DGCA Drone Rules 2021 and check the Digital Sky airspace map: fly only in green zones, below 120 m, in sight, and away from people, roads and airports.
Ideas that reuse this build: Build a 5-inch analog freestyle quad. They are listed under Take it further on this page.
A complete 5-inch freestyle drone: carbon frame, F405 stack, 2306 motors, ELRS radio link and analog goggles.
A 450 mm quad that holds position on GPS, flies waypoint missions and can drop a small payload.
Learning project. Check every circuit and the datasheet of each part before you power it up.