Component guide · Intermediate · 4 min read
Digital HD FPV Systems

DJI O3 Air Unit and ND Filter, Walksnail Avatar HD VTX, Cameras and VRX, Caddx Nebula Pro and Polar, RunCam Link and Wasp, CubePilot HD VTX, RadioLink DiViT and SIYI HM30 Long Range Video Links
By Geekobot Learning Team · Updated 29 Oct 2026
On this page
A digital FPV system sends sharp HD video from the drone to your goggles, replacing the fuzzy analog picture. Each system only talks to its own goggles: DJI O3 needs DJI goggles, Walksnail Avatar and Caddx Polar need Walksnail goggles or the Avatar VRX, and RunCam Link works with DJI V2 goggles. The SIYI HM30 is a longer range link with Ethernet video and control for mapping and survey drones.
Key specs at a glance
- Video
- 720p to 1080p, up to 100 fps or more by system
- Latency
- About 20 to 40 ms
- Band
- 5.8 GHz (FPV), 2.4 GHz (SIYI HM30)
- Supply
- 7.4V to 26V (2S to 6S) on most air units
- Range
- Several km (FPV), up to around 30 km (HM30) in open areas
- Onboard recording
- 1080p or 4K on DJI O3 and Walksnail units
Models in this guide
These are alternatives. Pick the one that fits your project; you only need one.
Option 1CaddxFPV Avatar HD VTX Module Only₹14,689
Option 2CaddxFPV Nebula Pro Digital Camera – Black₹5,489
Option 3CaddxFPV Nebula Pro Nano FPV Camera with 8cm Cable – Black₹5,509
Option 4CaddxFPV Polar Micro Camera with 12cm Coaxial Cable – Silver₹5,669
Option 5CaddxFPV Polar Starlight Digital HD FPV Air Unit₹18,349
Option 6CaddxFPV Walksnail Avatar HD Camera (with 14cm cable)₹6,349
What the Digital HD FPV systems: DJI O3, Walksnail Avatar, Caddx Polar, RunCam Link and SIYI HM30 is
Digital HD FPV systems send high-definition video from the drone to the goggles with low delay, replacing the analog camera and VTX.
Pick the goggles first, because the air unit must match them. Then check the camera, cable length and mounting size for your frame: nano cameras for 2 to 3 inch frames, full-size cameras for 5 inch.
The air unit runs hot. Never power it on the bench for long without airflow or the antennas fitted, or it can overheat and the transmitter can be damaged. Set the frequency and power legally for your country, and connect the UART to the flight controller so the OSD shows battery voltage and flight data.
Digital HD FPV systems: DJI O3, Walksnail Avatar, Caddx Polar, RunCam Link and SIYI HM30 pinout
The pins on the Digital HD FPV systems: DJI O3, Walksnail Avatar, Caddx Polar, RunCam Link and SIYI HM30 and what each one does.
| Pin | Function |
|---|---|
| VIN / GND | Battery voltage, 2S to 6S by model |
| TX / RX | UART to flight controller for MSP OSD |
| SBUS / DJI RC | Optional RC link on DJI units |
| Camera coax / MIPI | Camera cable |
| Antenna IPEX / MMCX | Fit before powering |
- VIN / GND
- Battery voltage, 2S to 6S by model
- TX / RX
- UART to flight controller for MSP OSD
- SBUS / DJI RC
- Optional RC link on DJI units
- Camera coax / MIPI
- Camera cable
- Antenna IPEX / MMCX
- Fit before powering
Wiring the Digital HD FPV systems: DJI O3, Walksnail Avatar, Caddx Polar, RunCam Link and SIYI HM30
Always fit the antenna before power-up. A transmitter without an antenna can burn out.
| Digital HD FPV systems: DJI O3, Walksnail Avatar, Caddx Polar, RunCam Link and SIYI HM30 pin | Flight controller | Note |
|---|---|---|
| VIN | Battery pad or 10V BEC | Check air unit range |
| GND | GND | |
| TX | FC UART RX | MSP DisplayPort |
| RX | FC UART TX |
- VIN
- Flight controller:
- Battery pad or 10V BEC
- Note:
- Check air unit range
- GND
- Flight controller:
- GND
- TX
- Flight controller:
- FC UART RX
- Note:
- MSP DisplayPort
- RX
- Flight controller:
- FC UART TX
Example code
Menu and command names change between Betaflight versions and air unit firmware; check the release notes for your versions.
1. Wire the air unit TX/RX to a free UART on the flight controller.
2. Betaflight Ports tab: turn on MSP for that UART.
3. Configuration tab: enable OSD.
4. CLI: set osd_displayport_device = MSP
5. CLI: set vcd_video_system = HD, then save.
6. Bind the air unit to the goggles with both bind buttons.
7. Arrange OSD items in the OSD tab and test with props off.Setup and tuning
the air unit, goggles and firmware must be from the same system (DJI, Walksnail or HDZero).
feed the air unit from the battery voltage range it accepts (often 2S to 6S).
never power the air unit without antennas.
air units get hot on the bench; power them only briefly without airflow.
connect the UART for Betaflight OSD and set the MSP DisplayPort settings.
What you need
Shop this list16 of 16 found in our store · ₹4,40,342
CaddxFPV Avatar HD VTX Module Only: the part this guide coversCaddxFPV Avatar HD VTX Module Only₹14,689
CaddxFPV Nebula Pro Digital Camera – Black: another version this guide coversCaddxFPV Nebula Pro Digital Camera – Black₹5,489
CaddxFPV Nebula Pro Nano FPV Camera with 8cm Cable – Black: another version this guide coversCaddxFPV Nebula Pro Nano FPV Camera with 8cm Cable – Black₹5,509
CaddxFPV Polar Micro Camera with 12cm Coaxial Cable – Silver: another version this guide coversCaddxFPV Polar Micro Camera with 12cm Coaxial Cable – Silver₹5,669
CaddxFPV Polar Starlight Digital HD FPV Air Unit: another version this guide coversCaddxFPV Polar Starlight Digital HD FPV Air Unit₹18,349
CaddxFPV Walksnail Avatar HD Camera (with 14cm cable): another version this guide coversCaddxFPV Walksnail Avatar HD Camera (with 14cm cable)₹6,349
CaddxFPV Walksnail Avatar HD VRX: another version this guide coversCaddxFPV Walksnail Avatar HD VRX₹38,979
CubePilot CubePilot HD Digital Video Transmitter: another version this guide coversCubePilot HD Digital Video Transmitter₹2,24,889
DJI O3 Air Unit: another version this guide coversDJI O3 Air Unit₹35,924
Flywoo DJI O3 Air Unit ND8 Filter: another version this guide coversFlywoo DJI O3 Air Unit ND8 Filter₹709
RadioLink DiViT Digital Image Transmission Adapter Board: another version this guide coversRadioLink DiViT Digital Image Transmission Adapter Board₹834
RunCam Link Digital FPV Air Unit: another version this guide coversRunCam Link Digital FPV Air Unit₹9,799
RunCam Link Wasp Digital HD FPV VTX Camera System: another version this guide coversRunCam Link Wasp Digital HD FPV VTX Camera System₹14,790
SIYI HM30 Full HD Digital Image Transmission FPV System: another version this guide coversSIYI HM30 Full HD Digital Image Transmission FPV System₹36,706
SIYI HM30 MK32 Dual Air Unit with Long Range Full HD Image Transmission SBUS PWM Ethernet Mavlink Telemetry Datalink: another version this guide coversSIYI HM30 MK32 Dual Air Unit with Long Range Full HD Image Transmission SBUS PWM Ethernet Mavlink Telemetry Datalink₹14,489
Walksnail Avatar nano HD Camera (with 9cm cable): another version this guide coversWalksnail Avatar nano HD Camera (with 9cm cable)₹7,169
Alternatives and when to choose them
- FPV VTX video transmitters: analog video transmitters.
- FPV goggles and video receivers: what receives the video.
- Drone gimbal cameras: survey and payload cameras.
Common mistakes to avoid
- Powering the air unit without antennas.
- Mixing parts from different digital systems.
- Running the air unit for minutes on the bench without cooling.
- Feeding it a voltage outside its input range.
Frequently asked questions
Can I use DJI goggles with a Walksnail air unit?
No. The systems are not compatible with each other.
How much latency does digital FPV have?
About 20 to 40 ms, close enough to analog for most flying.
Why does my air unit overheat on the bench?
It needs airflow. Keep bench sessions short or use a fan.
Can I record HD video on the drone?
Yes. Many air units record onboard, and goggles also record.
Do I need a special flight controller?
No, but it needs a free UART for OSD and control.
Parts for this guide
Keep learning
Sources
Written by the Geekobot team from manufacturer datasheets. Always check the datasheet for the exact part and variant you buy.
