How-to · Intermediate · 3 min read
FPV Video Transmitters (VTX)
5.8 GHz Analog Power, Channels, Wiring and Safety
By Geekobot Learning Team · Updated 29 Oct 2026
On this page
A VTX sends your camera picture to the goggles. Choose power by use: 25 to 600 mW for freestyle and racing, higher for long range. Power it from a regulated supply, connect video and the control wire (SmartAudio or Tramp), set the band and channel to match your goggles and never power it without an antenna. Use pit mode on the ground and cool it with airflow.
Key specs at a glance
- Band
- 5.8 GHz analog, bands A, B, E, F and Race (up to 48 channels)
- Power
- 25 mW to 5.5 W depending on model
- Input
- 5 V to 25 V; check each model
- Control
- SmartAudio or IRC Tramp over one wire
- Connector
- MMCX, U.FL or SMA antenna
- Receivers
- Goggles, RX5808 modules, OTG phone receivers
Pick the power level
More power is not always better.
| Power | Use | Notes |
|---|---|---|
| 25 to 200 mW | Racing, indoor, tiny drones | Least interference, little heat |
| 400 to 800 mW | Freestyle and cinewhoop | Good balance; common |
| 1.6 W to 3 W | Long range line of sight | Needs airflow and a stable supply |
| 5 W and above | Special long-range only | High heat; check legal limits |
- 25 to 200 mW
- Use:
- Racing, indoor, tiny drones
- Notes:
- Least interference, little heat
- 400 to 800 mW
- Use:
- Freestyle and cinewhoop
- Notes:
- Good balance; common
- 1.6 W to 3 W
- Use:
- Long range line of sight
- Notes:
- Needs airflow and a stable supply
- 5 W and above
- Use:
- Special long-range only
- Notes:
- High heat; check legal limits
Wiring
Connect the VTX to the flight controller or a regulated supply (check the voltage range), connect the camera's video wire to the VTX video input and the VTX control wire to a spare UART TX for SmartAudio or Tramp. In Betaflight set the UART to VTX control, then pick band, channel and power from the OSD menu. See FC and ESC stacks and PDB and BEC. Keep the supply clean with a capacitor.
Antenna and heat
Never power a VTX without its antenna: reflected power can destroy the output stage. Use a good antenna and keep it away from carbon; see FPV antennas. High-power VTXs get very hot, so give them airflow, a heatsink, or limit power on the bench. Use pit mode on the ground.
Receivers and channels
Match the band and channel on the goggles. Analog receivers range from built-in goggle modules to DIY RX5808 diversity boards and phone OTG receivers. Agree channels with other pilots to avoid interference. For goggles see FPV goggles and receivers, and for cameras see FPV cameras.
Rules
Legal 5.8 GHz power and channels vary by country. Check what you may use before flying, and do not exceed the legal power. Digital systems have their own VTX units; see FPV video systems.
Try it: Link budget fspl calculator
Change the values and the diagram and results update as you type.
Common mistakes to avoid
- Powering the VTX without an antenna.
- Using high power on the bench without cooling.
- Mismatching channels between VTX and goggles.
- Powering a 5 V VTX from a noisy rail.
- Exceeding legal power.
Frequently asked questions
How much VTX power do I need?
25 to 600 mW suits most flying. Higher power only for long range.
What is pit mode?
A very low-power setting used on the ground.
What is SmartAudio?
A one-wire control protocol for changing VTX settings.
Why does my VTX overheat?
Insufficient airflow or too high power on the ground.
Can I use a VTX with digital goggles?
No. Digital systems have their own matched units.
Parts for this guide
Calculators
Terms in this guide
Projects that use it
Put this into practice: 1 step-by-step build in our project library uses parts from this guide.
Keep learning
Sources
Written by the Geekobot team from manufacturer datasheets. Always check the datasheet for the exact part and variant you buy.






