How-to · Intermediate · 3 min read
Drone PDBs and BECs
Power Distribution Boards and Voltage Regulators
By Geekobot Learning Team · Updated 29 Oct 2026
On this page
A power distribution board (PDB) shares battery power between ESCs, while a BEC or UBEC steps the battery voltage down to 5 V or 12 V for the flight controller, receiver, camera and servos. Pick a BEC rated for your battery cell count and well above the load current, use separate regulators for noisy servos, and keep wiring short and thick.
Key specs at a glance
- PDB
- Distributes battery power to ESCs; rated by total current
- BEC / UBEC
- Switching regulator; common outputs 5 V, 9 V, 12 V
- Input range
- 2S to 6S, 2S to 8S or up to 12S; check the label
- Current
- 1 A to 25 A or more
- Types
- Switching (efficient) or linear (noisy and hot)
- Filtering
- Capacitors and ferrites reduce noise
This part can carry many amps. Use wire thick enough for the current, put a fuse close to the battery, check that connectors are rated for the load and give drivers and motors room to cool. A short at these currents melts wires in seconds.
PDB vs BEC
A PDB is a board with large copper pads that splits the battery supply to each ESC. A BEC is a regulator. Many modern 4-in-1 ESCs and flight controllers already include a PDB and BEC, so you may not need a separate board. Larger drones, fixed-wing planes and servo-heavy builds still use separate units.
Choosing a BEC
Pick by input voltage and load.
| Use | Output | Example loads |
|---|---|---|
| Flight controller, receiver | 5 V 1 to 3 A | FC, RX, GPS |
| Camera and VTX | 9 V or 12 V 1 to 3 A | FPV camera, VTX, LEDs |
| Servos on planes | 5 to 6 V, 5 to 25 A | Control surfaces |
| Payload | Adjustable 5 to 24 V | Gimbals, lights |
- Flight controller, receiver
- Output:
- 5 V 1 to 3 A
- Example loads:
- FC, RX, GPS
- Camera and VTX
- Output:
- 9 V or 12 V 1 to 3 A
- Example loads:
- FPV camera, VTX, LEDs
- Servos on planes
- Output:
- 5 to 6 V, 5 to 25 A
- Example loads:
- Control surfaces
- Payload
- Output:
- Adjustable 5 to 24 V
- Example loads:
- Gimbals, lights
Noise and protection
Motors and ESCs create voltage spikes. Place a low-ESR capacitor on the battery input and keep the BEC away from receiver antennas. Use a separate regulator for servos so their current spikes do not reset the flight controller. A switching BEC is much more efficient than a linear one, which wastes extra voltage as heat. See DC-DC converters and voltage regulators.
Wiring tips
- 1Use wire thick enough for the current; see the wire gauge calculator.
- 2Solder pads fully and use heat-shrink; cold joints overheat.
- 3Match polarity with care. A reversed battery connection destroys electronics instantly.
- 4Test the output voltage with a multimeter before connecting sensitive parts.
- 5Add a fuse or smoke stopper for first power-up on new builds.
Try it: Wire gauge calculator
Change the values and the diagram and results update as you type.
Common mistakes to avoid
- Using a 5 V BEC on a battery voltage above its input rating.
- Powering servos from the flight controller's 5 V pad.
- Skipping the input capacitor.
- Using thin wire for high current.
- Reversing polarity on the battery lead.
Frequently asked questions
Do I need a PDB with a 4-in-1 ESC?
No, the ESC board distributes power to the motors already.
BEC or UBEC?
UBEC means universal BEC, a switching type that accepts a wide voltage range.
Can I power servos from the flight controller?
Not recommended. Use a separate regulator sized for servo current.
What current rating?
At least 1.5 times the load current.
Why does my BEC get hot?
It may be a linear type, or overloaded. Use a switching BEC with margin.
Parts for this guide
Calculators
Terms in this guide
Projects that use it
Put this into practice: 1 step-by-step build in our project library uses parts from this guide.
Keep learning
Sources
Written by the Geekobot team from manufacturer datasheets. Always check the datasheet for the exact part and variant you buy.




