Build a 5-inch FPV freestyle quad (analog video, ELRS)
A complete 5-inch freestyle drone: carbon frame, F405 stack, 2306 motors, ELRS radio link and analog goggles.
Shop by category
Shop all componentsA Pixhawk running ArduPilot turns a simple F450 frame into a drone that holds its position, returns home and flies missions you plan on a laptop or phone. Big 2213 motors and 10-inch props give a gentle, efficient lift, a M8N GPS with compass tells the autopilot where it is, and a servo dropper and navigation lights show how to add payloads.
Take the propellers off whenever the drone is on the bench and connected to a computer or battery.
LiPo batteries can catch fire if punctured, over-discharged or charged without balance leads. Charge on a fireproof surface, never leave them charging unattended and store them at storage voltage (about 3.8 V per cell).
Before you fly, read the DGCA Drone Rules 2021 and check the Digital Sky airspace map: fly only in green zones, below 120 m, in sight, and away from people, roads and airports.
Test the payload dropper on the ground first and never drop anything over people or property.
Tick anything you already have and the total updates.
Propeller guards for F450/F550 frames while you learn to fly
Collet prop adaptor for motors with a plain shaft
450 mm frame with power board and landing gear
ArduPilot autopilot with SD card and buzzer
GPS with compass for position hold and missions
Lifts the GPS away from power wires
Motor and 10-inch prop combo (CW)
Motor and 10-inch prop combo (CCW)
Separate power board, for a frame without one built in
ELRS receiver; ArduPilot reads it as CRSF
Spare 220 mm arm: the part that breaks first in a crash
Upgrade path: heavy-lift motors for a larger 650 mm frame and 12-inch props
Helps you see orientation in low light
Only for a fixed-wing build on the same Pixhawk; a quad does not use it
Only with a 900 MHz ELRS module, for longer range
Follow the colours: red is power, dark grey is ground, blue is a signal.
3S LiPo, about 3000 to 5000 mAh, bought separately. The SimonK ESCs are rated for 2 to 3S only.
ardupilot-params.txt# ArduCopter parameters for this build (set in Mission Planner > Full Parameter List)
FRAME_CLASS 1 # Quad
FRAME_TYPE 1 # X
SERIAL2_PROTOCOL 23 # RC input (CRSF) on TELEM2
RSSI_TYPE 3 # RSSI from the receiver protocol
FS_THR_ENABLE 1 # radio failsafe: RTL
BATT_FS_LOW_ACT 2 # low battery: RTL
FENCE_ENABLE 1
SERVO9_FUNCTION 1 # AUX1 = RCPassThru: servo 9 follows RC channel 9, so put channel 9 on a switch
Move the GPS mast further from the power wires, redo the compass calibration outside, and check the arrow points forward.
Calibrate the radio in Mission Planner and check SERIAL2_PROTOCOL is 23 for the CRSF receiver.
Recalibrate all ESCs together; SimonK ESCs need a matching throttle range.
Yes, a light action camera. Keep the total weight within what four 2213 motors with 10-inch props lift comfortably at about half throttle.
Mission Planner on a laptop over USB is enough to set up. A telemetry radio lets you watch the drone live.
Fixed-wing planes use it to measure speed through the air. A quad does not need it.
19 parts: Propeller Guard for F450 F550 Quadcopters (Set of 4), BLHeli 30A ESC (BLS-MAX), Aluminium Bullet Motor Prop Adaptor (Collet Type), F450/Q450 Quadcopter Frame Kit – PCB & Landing Gear, Pixhawk PX4 Autopilot PIX 2.4.8 32 Bit Flight Controller – Standard Set w/ MicroSD & Buzzer, u-blox NEO-M8N GPS Module w/ Ceramic Active Antenna, YGRI M8N GPS Mount for Quadcopters – Aluminum Folding, 2 × EMAX MT2213 935KV Brushless DC Motor with 1045 Propeller Combo – Black Cap, 2 × EMAX MT2213 935KV Brushless DC Motor with 1045 Propeller Combo – Red Cap (CCW), 4 × SimonK 30A BLDC ESC with 5V 2A BEC (2-3S LiPo), plus 9 more. Tools: Hex Key (Allen Key). On this page you can tick the parts you already have and add only the rest to your cart.
It is a advanced project and takes about 3 days. The build on this page has 8 steps.
No. This page has the complete, tested code (ardupilot-params.txt).
About ₹53,858 for the parts at the prices on this page, plus tools if you do not have them. Quantity price breaks lower the cost when you build several.
ArduPilot setup in Mission Planner: frame, calibrations, flight modes; GPS and compass placement away from power wires; Power distribution and BECs; Planning an auto mission with return-to-launch.
Take the propellers off whenever the drone is on the bench and connected to a computer or battery. LiPo batteries can catch fire if punctured, over-discharged or charged without balance leads. Charge on a fireproof surface, never leave them charging unattended and store them at storage voltage (about 3.8 V per cell). Before you fly, read the DGCA Drone Rules 2021 and check the Digital Sky airspace map: fly only in green zones, below 120 m, in sight, and away from people, roads and airports. Test the payload dropper on the ground first and never drop anything over people or property.
Ideas that reuse this build: Build a 5-inch FPV freestyle quad. They are listed under Take it further on this page.
A complete 5-inch freestyle drone: carbon frame, F405 stack, 2306 motors, ELRS radio link and analog goggles.
A small, quiet 3-inch quad that records and streams clear HD video through a DJI O3 air unit.
Learning project. Check every circuit and the datasheet of each part before you power it up.