Component guide · Intermediate · 4 min read
Pixhawk 2.4.8 and 2.4.7 Clones, Mini Pixhawk, APM 2.8

With and Without Compass, With M8N GPS), Mini APM 3.1 and Holybro Micro APM
By Geekobot Learning Team · Updated 29 Oct 2026
On this page
The Pixhawk 2.4.8 is a low-cost copy of the original Pixhawk 1 (FMUv2/v3) and is the most common autopilot in student drone projects. It still runs current ArduPilot, though newer features need more flash memory. APM 2.8 boards are older 8-bit autopilots that stopped getting updates at ArduCopter 3.2.1; they are fine for learning but not for new serious builds.
Key specs at a glance
- Processor
- STM32F427 (Pixhawk 2.4.8) or ATmega2560 (APM)
- Firmware
- Current ArduPilot (Pixhawk); ArduCopter 3.2.1 max (APM)
- IMUs
- MPU6000 + L3GD20/LSM303 (Pixhawk)
- Outputs
- 8 MAIN + 6 AUX (Pixhawk), 8 (APM)
- Connectors
- DF13 (Pixhawk 2.4.8), pin headers (APM)
- Uses
- F450/S500 quads, learning, competitions
Models in this guide
These are alternatives. Pick the one that fits your project; you only need one.
Option 1Pixhawk 2.4.8 PX4 32 Bit Autopilot Flight Controller₹6,929
Option 2Pixhawk PX4 Autopilot PIX 2.4.8 32 Bit Flight Controller – Standard Set w/ MicroSD & Buzzer₹5,499
Option 3Pixhawk PX4 2.4.7 32-Bit Flight Controller for Quadcopter Multicopter₹12,999
Option 4ReadyToSky Mini Pixhawk 2.4.8 and Power Module₹3,189
Option 5Mini APM3.1 Flight Controller with Power Module – Standard Set₹3,499
Option 6APM 2.8 Flight Controller with Built-in Compass₹4,824
What the Pixhawk 2.4.8 and APM 2.8 clone flight controllers is
Pixhawk 2.4.8 and APM clones are low-cost copies of older flight controllers, still used on budget drones and for learning ArduPilot.
Many 2.4.8 boards have the 1 MB flash bug; ArduPilot detects it and loads a smaller build. Flash ArduPilot 'fmuv3' firmware for boards with 2 MB flash.
APM 2.8 can use the built-in compass or an external one (cut the jumper or choose the 'without compass' version for an external GPS-compass).
Pixhawk 2.4.8 and APM 2.8 clone flight controllers pinout
The pins on the Pixhawk 2.4.8 and APM 2.8 clone flight controllers and what each one does.
| Pin | Function |
|---|---|
| POWER1 / POWER2 | From the power module: 5V for the FC plus battery voltage and current |
| GPS1 / GPS2 | GPS, compass, safety switch and buzzer on one connector |
| TELEM1 / TELEM2 | Telemetry radio, companion computer or OSD |
| RC IN | SBUS, PPM, CRSF or DSM receiver |
| MAIN / AUX OUT (I/O PWM) | ESC and servo signals |
| Safety switch and buzzer | Required to arm on Pixhawk 2.4.8 unless disabled |
- POWER1 / POWER2
- From the power module: 5V for the FC plus battery voltage and current
- GPS1 / GPS2
- GPS, compass, safety switch and buzzer on one connector
- TELEM1 / TELEM2
- Telemetry radio, companion computer or OSD
- RC IN
- SBUS, PPM, CRSF or DSM receiver
- MAIN / AUX OUT (I/O PWM)
- ESC and servo signals
- Safety switch and buzzer
- Required to arm on Pixhawk 2.4.8 unless disabled
Wiring the Pixhawk 2.4.8 and APM 2.8 clone flight controllers
The safety switch must be pressed before arming unless BRD_SAFETYENABLE is set to 0. Power the board from the power module, never from the servo rail alone.
| Pixhawk 2.4.8 and APM 2.8 clone flight controllers pin | Port on the autopilot | Note |
|---|---|---|
| Power module | POWER1 | Battery through the PM to the PDB |
| GPS | GPS1 | Arrow forward, away from wires |
| Receiver | RC IN | SBUS or CRSF (set SERIAL protocol) |
| ESCs | MAIN OUT 1 to 4 (or FMU outputs) | Signal and GND only |
| Telemetry | TELEM1 | Air radio |
- Power module
- Port on the autopilot:
- POWER1
- Note:
- Battery through the PM to the PDB
- GPS
- Port on the autopilot:
- GPS1
- Note:
- Arrow forward, away from wires
- Receiver
- Port on the autopilot:
- RC IN
- Note:
- SBUS or CRSF (set SERIAL protocol)
- ESCs
- Port on the autopilot:
- MAIN OUT 1 to 4 (or FMU outputs)
- Note:
- Signal and GND only
- Telemetry
- Port on the autopilot:
- TELEM1
- Note:
- Air radio
Example code
Use Mission Planner for both Pixhawk and APM. For APM pick the legacy ArduCopter 3.2.1 firmware from the firmware archive.
1. Connect USB, Setup > Install Firmware > pick Copter, Plane or Rover
2. Mandatory Hardware:
Frame Type -> e.g. Quad X
Accel Calibration -> level, left, right, nose down, nose up, back
Compass -> Start, rotate the drone in all directions
Radio Calibration -> move all sticks and switches to their ends
Flight Modes -> Stabilize, AltHold, Loiter, RTL on a 3- or 6-way switch
ESC Calibration -> props off, follow the on-screen steps
Failsafe -> battery and radio failsafe to RTL or Land
3. Config > Full Parameter List: SERIAL1_PROTOCOL = 2 (MAVLink2) for telemetry
4. Test arm with props OFF, then hover test in an open fieldSetup and tuning
Pixhawk 2.4.8 runs current ArduPilot (fmuv3 or fmuv2 target); APM 2.8 is stuck at ArduCopter 3.2.1.
use a matching power module for clean 5 V and battery monitoring.
use an external GPS compass; disable the internal compass on clones.
connect the safety switch and buzzer, or disable the safety switch.
clones vary; check sensors and SD cards before flying.
What you need
Shop this list13 of 13 found in our store · ₹71,959
Pixhawk 2.4.8 PX4 32 Bit Autopilot Flight Controller: the part this guide coversPixhawk 2.4.8 PX4 32 Bit Autopilot Flight Controller₹6,929
Pixhawk PX4 Autopilot PIX 2.4.8 32 Bit Flight Controller – Standard Set w/ MicroSD & Buzzer: another version this guide coversPixhawk PX4 Autopilot PIX 2.4.8 32 Bit Flight Controller – Standard Set w/ MicroSD & Buzzer₹5,499
Pixhawk PX4 2.4.7 32-Bit Flight Controller for Quadcopter Multicopter: another version this guide coversPixhawk PX4 2.4.7 32-Bit Flight Controller for Quadcopter Multicopter₹12,999
ReadyToSky Mini Pixhawk 2.4.8 and Power Module: another version this guide coversReadyToSky Mini Pixhawk 2.4.8 and Power Module₹3,189
Mini APM3.1 Flight Controller with Power Module – Standard Set: another version this guide coversMini APM3.1 Flight Controller with Power Module – Standard Set₹3,499
APM 2.8 Flight Controller with Built-in Compass: another version this guide coversAPM 2.8 Flight Controller with Built-in Compass₹4,824
APM 2.8 Flight Controller without Compass: another version this guide coversAPM 2.8 Flight Controller without Compass₹6,118
APM 2.8 Flight Controller with M8N GPS: another version this guide coversAPM 2.8 Flight Controller with M8N GPS₹12,000
Holybro Micro APM Flight Controller: another version this guide coversHolybro Micro APM Flight Controller₹3,164
BN-880 GPS and compass module: a low-cost GPS for clone boardsReadyToSky BN-880 GPS GLONASS Compass Module₹1,669Closest match, check the specs
APM/Pixhawk power module V6.0: power and battery sensing for clone boardsAPM/Pixhawk Power Module V6.0 3A BEC XT60 (2-6S, 90A)₹539Closest match, check the specs
Holybro SiK telemetry radio V3 433 MHz: live link to Mission Planner or QGroundControlHolybro Sik Telemetry Radio V3 100 mW 433 MHz₹9,949Closest match, check the specs
ELRS 2.4G receiver (PWM/CRSF): the radio control linkHGLRC ELRS 2.4G Receiver₹1,581Closest match, check the specs
Alternatives and when to choose them
- Holybro Pixhawk 6C: modern and supported.
- Pixhawk autopilots: ArduPilot basics.
- Multirotor ESCs: ESCs for F450.
Common mistakes to avoid
- Expecting modern firmware on APM.
- Using the internal compass.
- Skipping sensor checks.
- Using the original poor SD card.
Frequently asked questions
Can a Pixhawk 2.4.8 run the latest ArduPilot?
Yes, using the fmuv3 target, though flash space limits some features.
Why does my clone fail pre-arm checks?
Compass, accelerometer or safety switch is not set up.
Should I buy an APM 2.8 today?
Only for learning, because the APM 2.8 cannot run any modern ArduPilot firmware.
Do I need the safety switch?
Either connect and press it before arming, or disable it with the BRD_SAFETY parameter.
Why does the SD card give errors?
Clone SD cards are often poor; replace with a good card.
Parts for this guide
Keep learning
Sources
Written by the Geekobot team from manufacturer datasheets. Always check the datasheet for the exact part and variant you buy.

