Component guide · Advanced · 6 min read
Holybro Pixhawk 6X, 6X Rev8, 6X Pro, 6X-RT and 6C Autopilots, Pix32 v6,

and Raspberry Pi CM4 and Jetson Baseboards
By Geekobot Learning Team · Updated 29 Oct 2026
On this page
The Pixhawk 6 family is Holybro's current autopilot range. The 6C (and 6C Mini) is the value choice with an H743 processor and two IMUs. The 6X adds triple isolated IMUs, Ethernet and modular baseboards; the 6X Pro uses industrial-grade IMUs; and the 6X-RT uses an NXP processor for PX4 developers. The CM4 and Jetson baseboards put a companion computer next to the autopilot.
Key specs at a glance
- Processor
- STM32H753 (6X, 6C) or NXP i.MX RT1176 (6X-RT)
- IMUs
- 2 (6C), 3 isolated and heated (6X), ADIS16470 (6X Pro)
- Firmware
- ArduPilot and PX4
- Interfaces
- CAN x2, Ethernet (6X), UARTs, I2C, SPI
- Outputs
- 8 IO + 8 FMU PWM (16 total on standard sets)
- Companion
- Raspberry Pi CM4 or Jetson Orin baseboards
Models in this guide
These are alternatives. Pick the one that fits your project; you only need one.
Option 1Holybro Pixhawk 6C Flight Controller (Plastic Case)₹27,879
Option 2Holybro Pixhawk 6C Aluminium Body – NO GPS NO Power Module₹35,699
Option 3Holybro Pixhawk 6C Flight Controller + PM02 Power Module₹36,439
Option 4Holybro Pixhawk 6C Flight Controller + PM07 Power Module + M9N GPS₹43,689
Option 5Holybro Pixhawk 6C Mini Flight Controller₹21,938
Option 6Holybro Pixhawk 6X Autopilot Flight Controller Standard Set (No GPS)₹33,047
What the Holybro Pixhawk 6X, 6X Pro, 6X-RT, 6C and Pix32 v6 autopilots is
The Holybro Pixhawk 6X and 6C are current Pixhawk autopilots with STM32H7 processors; the 6X is the modular, higher-end version with isolated triple IMUs and Ethernet.
For most student and research drones the Pixhawk 6C with a PM02 and M10 GPS is enough. Choose the 6X for redundancy and Ethernet payloads, the 6X Pro for survey-grade stability, and the CM4 or Jetson baseboard to run computer vision, ROS 2 or MAVSDK on board.
Rev8 6X units use updated IMUs; the set and module options are the same.
Holybro Pixhawk 6X, 6X Pro, 6X-RT, 6C and Pix32 v6 autopilots pinout
The pins on the Holybro Pixhawk 6X, 6X Pro, 6X-RT, 6C and Pix32 v6 autopilots and what each one does.
| Pin | Function |
|---|---|
| POWER1 / POWER2 | From the power module: 5V for the FC plus battery voltage and current |
| GPS1 / GPS2 | GPS, compass, safety switch and buzzer on one connector |
| TELEM1 / TELEM2 | Telemetry radio, companion computer or OSD |
| RC IN | SBUS, PPM, CRSF or DSM receiver |
| MAIN / AUX OUT (I/O PWM) | ESC and servo signals |
| CAN1 / CAN2 | DroneCAN GPS, ESCs and sensors |
| ETH | Ethernet to a companion computer or payload (6X) |
- POWER1 / POWER2
- From the power module: 5V for the FC plus battery voltage and current
- GPS1 / GPS2
- GPS, compass, safety switch and buzzer on one connector
- TELEM1 / TELEM2
- Telemetry radio, companion computer or OSD
- RC IN
- SBUS, PPM, CRSF or DSM receiver
- MAIN / AUX OUT (I/O PWM)
- ESC and servo signals
- CAN1 / CAN2
- DroneCAN GPS, ESCs and sensors
- ETH
- Ethernet to a companion computer or payload (6X)
Wiring the Holybro Pixhawk 6X, 6X Pro, 6X-RT, 6C and Pix32 v6 autopilots
Mount the autopilot near the centre of gravity with the arrow forward on the supplied foam or damping mount. Never power the servo rail from the power module; use a separate BEC if servos need power.
| Holybro Pixhawk 6X, 6X Pro, 6X-RT, 6C and Pix32 v6 autopilots pin | Port on the autopilot | Note |
|---|---|---|
| Power module | POWER1 | Battery through the PM to the PDB |
| GPS | GPS1 | Arrow forward, away from wires |
| Receiver | RC IN | SBUS or CRSF (set SERIAL protocol) |
| ESCs | MAIN OUT 1 to 4 (or FMU outputs) | Signal and GND only |
| Telemetry | TELEM1 | Air radio |
- Power module
- Port on the autopilot:
- POWER1
- Note:
- Battery through the PM to the PDB
- GPS
- Port on the autopilot:
- GPS1
- Note:
- Arrow forward, away from wires
- Receiver
- Port on the autopilot:
- RC IN
- Note:
- SBUS or CRSF (set SERIAL protocol)
- ESCs
- Port on the autopilot:
- MAIN OUT 1 to 4 (or FMU outputs)
- Note:
- Signal and GND only
- Telemetry
- Port on the autopilot:
- TELEM1
- Note:
- Air radio
Example code
PX4 users do the same in QGroundControl. Re-do the compass calibration whenever wiring near the GPS changes. On the CM4 or Jetson baseboard the companion computer talks MAVLink over the internal TELEM2 link.
1. Connect USB, Setup > Install Firmware > pick Copter, Plane or Rover
2. Mandatory Hardware:
Frame Type -> e.g. Quad X
Accel Calibration -> level, left, right, nose down, nose up, back
Compass -> Start, rotate the drone in all directions
Radio Calibration -> move all sticks and switches to their ends
Flight Modes -> Stabilize, AltHold, Loiter, RTL on a 3- or 6-way switch
ESC Calibration -> props off, follow the on-screen steps
Failsafe -> battery and radio failsafe to RTL or Land
3. Config > Full Parameter List: SERIAL1_PROTOCOL = 2 (MAVLink2) for telemetry
4. Test arm with props OFF, then hover test in an open fieldSetup and tuning
flash PX4 or ArduPilot from QGroundControl or Mission Planner.
use PM02D on the 6X or PM02 on the 6C, matched to the autopilot.
mount at the centre of gravity with the arrow forward, on foam or the isolated base.
connect GPS to GPS1, telemetry to TELEM1 and RC to RC IN.
run sensor, radio and ESC calibration before the first flight.
on the 6X, connect a companion computer over Ethernet for MAVLink or DDS.
What you need
Shop this list20 of 20 found in our store · ₹7,74,670
Holybro Pixhawk 6C Flight Controller (Plastic Case): the part this guide coversHolybro Pixhawk 6C Flight Controller (Plastic Case)₹27,879
Holybro Pixhawk 6C Aluminium Body – NO GPS NO Power Module: another version this guide coversHolybro Pixhawk 6C Aluminium Body – NO GPS NO Power Module₹35,699
Holybro Pixhawk 6C Flight Controller + PM02 Power Module: another version this guide coversHolybro Pixhawk 6C Flight Controller + PM02 Power Module₹36,439
Holybro Pixhawk 6C Flight Controller + PM07 Power Module + M9N GPS: another version this guide coversHolybro Pixhawk 6C Flight Controller + PM07 Power Module + M9N GPS₹43,689
Holybro Pixhawk 6C Mini Flight Controller: another version this guide coversHolybro Pixhawk 6C Mini Flight Controller₹21,938
Holybro Pixhawk 6X Autopilot Flight Controller Standard Set (No GPS): another version this guide coversHolybro Pixhawk 6X Autopilot Flight Controller Standard Set (No GPS)₹33,047
Holybro Pixhawk 6X Flight Controller Module Only (No GPS): another version this guide coversHolybro Pixhawk 6X Flight Controller Module Only (No GPS)₹21,896
Holybro Pixhawk 6X Mini Set Only (No GPS included): another version this guide coversHolybro Pixhawk 6X Mini Set Only (No GPS included)₹21,574
Holybro Pixhawk 6X Mini Set with M10 GPS: another version this guide coversHolybro Pixhawk 6X Mini Set with M10 GPS₹42,726
Holybro Pixhawk 6X Standard Set with M10 GPS: another version this guide coversHolybro Pixhawk 6X Standard Set with M10 GPS₹37,369
Holybro Pixhawk 6X Standard Set v2A: another version this guide coversHolybro Pixhawk 6X Standard Set v2A₹47,639
Holybro Pixhawk 6X Standard Set v2A + M10 GPS: another version this guide coversHolybro Pixhawk 6X Standard Set v2A + M10 GPS₹47,189
Holybro Pixhawk 6X Standard Set v2B: another version this guide coversHolybro Pixhawk 6X Standard Set v2B₹42,029
Holybro Pixhawk 6X Standard Set v2B + M10 GPS: another version this guide coversHolybro Pixhawk 6X Standard Set v2B₹42,029
Holybro Pixhawk 6X (Rev8) Mini Set: another version this guide coversHolybro Pixhawk 6X (Rev8) Mini Set₹35,719
Holybro Pixhawk 6X (Rev8) Mini Set + M10 GPS: another version this guide coversHolybro Pixhawk 6X (Rev8) Mini Set₹35,719
Holybro Pixhawk 6X (Rev8) Mini Set with M9N GPS: another version this guide coversHolybro Pixhawk 6X (Rev8) Mini Set₹35,719
Holybro Pixhawk 6X (Rev8) – FC Module Only: another version this guide coversHolybro Pixhawk 6X (Rev8) – FC Module Only₹14,843
Holybro Pixhawk 6X Pro Flight Controller Module: another version this guide coversHolybro Pixhawk 6X Pro Flight Controller Module₹61,499
Holybro Pixhawk 6X Pro Mini Set – Flight Controller Module, Mini Baseboard, PM02D HV Power Module: another version this guide coversHolybro Pixhawk 6X Pro Mini Set – Flight Controller Module, Mini Baseboard, PM02D HV Power Module₹90,029
Alternatives and when to choose them
- Pixhawk 4 and 5X: earlier models.
- CUAV, Cube and other autopilots: other brands.
- Pixhawk GPS modules: GPS choices.
Common mistakes to avoid
- Using an analog power module on the 6X.
- Calibrating near metal.
- Skipping failsafe setup.
- Mounting without vibration damping.
Frequently asked questions
Which should I buy, Pixhawk 6X or 6C?
6C is cheaper and fine for most drones; 6X adds redundancy and Ethernet for advanced builds.
Can I use the old Pixhawk 4 GPS on a 6C?
Yes, if the connector type matches.
Why is there a pre-arm error about compass?
The compass is uncalibrated or near magnetic interference.
Can I connect a companion computer?
Yes, over TELEM2 serial or Ethernet on the 6X.
Does the 6X support CAN ESCs?
Yes, it has two CAN ports for DroneCAN ESCs and sensors.
Parts for this guide
- ₹27,879View
- ₹35,699View
- ₹36,439View
- ₹43,689View
- ₹21,938View
- ₹33,047View
- ₹21,896View
- ₹21,574View
- ₹42,726View
- ₹37,369View
- ₹47,639View
- ₹47,189View
- ₹42,029View
- ₹47,189View
- ₹35,719View
- ₹42,029View
- ₹44,129View
- ₹14,843View
- ₹61,499View
- ₹90,029View
- ₹1,12,649View
- ₹1,12,649View
- ₹36,356View
- ₹21,589View
- ₹36,865View
- ₹42,979View
- ₹55,622View
- ₹62,409View
- ₹25,629View
- ₹15,939View
- ₹3,769View
- ₹6,229View
- ₹3,481View
- ₹9,949View
- ₹1,069View
Keep learning
Sources
Written by the Geekobot team from manufacturer datasheets. Always check the datasheet for the exact part and variant you buy.


















