Component guide · Advanced · 5 min read
Autopilots

CUAV V6X, Nora+, X7+ and X25 EVO, Cube Orange+, SIYI N7, RadioLink PIX6 and Mini Pix, Syncore U1, PDRL Ag++, VECROS JETCORE, Omni Mini and DJI Naza-M Lite
By Geekobot Learning Team · Updated 29 Oct 2026
On this page
These autopilots run ArduPilot or PX4 (or their own firmware) and compete with Holybro's Pixhawks. CUAV's V6X and X7+ are industrial with good vibration isolation; the Cube Orange+ is the long-standing choice with ADS-B on the standard set; SIYI N7 bundles a 14S power module; RadioLink boards are budget options. PDRL, VECROS, Syncore, HC Robotics and Omni Mini are made in India.
Key specs at a glance
- Firmware
- ArduPilot, PX4, or maker firmware (Naza, PDRL)
- Processors
- STM32H7 on most current boards
- IMUs
- 2 to 3, isolated on CUAV and Cube
- Power
- Bundled modules on SIYI and CUAV sets
- Extras
- ADS-B (Cube standard set), CAN, Ethernet (X25 EVO)
- Uses
- Survey, agriculture, research, education
Models in this guide
These are alternatives. Pick the one that fits your project; you only need one.
Option 1CUAV Pixhawk V6X V2 Flight Controller₹43,948
Option 2CUAV V6X Flight Controller₹29,999
Option 3CUAV Nora+ Flight Controller₹47,249
Option 4CUAV X7+ Flight Controller | Autopilot For PX4 & APM Drone Hardware₹29,209
Option 5CUAV X7+ Pro Flight Controller | Autopilot for PX4 APM Drone Quadcopter Pixhawk₹92,049
Option 6CUAV X25 EVO Pixhawk Autopilot Flight Controller₹46,719
What the CUAV, CubePilot, SIYI, RadioLink and Indian-made autopilots is
These are autopilot flight controllers, such as CUAV, Cube Orange+, SIYI N7 and RadioLink PIX6, that run ArduPilot or PX4 for autonomous drones, planes and rovers.
For DGCA-compliant agriculture and survey drones in India, PDRL Ag++ and other local autopilots come with Indian ground-station software. The DJI Naza-M Lite is a closed system for simple GPS-hold multirotors and needs its GPS and LED modules.
Most of the others use standard Pixhawk connectors, so GPS, telemetry and power modules are interchangeable.
CUAV, CubePilot, SIYI, RadioLink and Indian-made autopilots pinout
The pins on the CUAV, CubePilot, SIYI, RadioLink and Indian-made autopilots and what each one does.
| Pin | Function |
|---|---|
| POWER1 / POWER2 | From the power module: 5V for the FC plus battery voltage and current |
| GPS1 / GPS2 | GPS, compass, safety switch and buzzer on one connector |
| TELEM1 / TELEM2 | Telemetry radio, companion computer or OSD |
| RC IN | SBUS, PPM, CRSF or DSM receiver |
| MAIN / AUX OUT (I/O PWM) | ESC and servo signals |
| CAN1 / CAN2 | DroneCAN GPS, ESCs and sensors |
- POWER1 / POWER2
- From the power module: 5V for the FC plus battery voltage and current
- GPS1 / GPS2
- GPS, compass, safety switch and buzzer on one connector
- TELEM1 / TELEM2
- Telemetry radio, companion computer or OSD
- RC IN
- SBUS, PPM, CRSF or DSM receiver
- MAIN / AUX OUT (I/O PWM)
- ESC and servo signals
- CAN1 / CAN2
- DroneCAN GPS, ESCs and sensors
Wiring the CUAV, CubePilot, SIYI, RadioLink and Indian-made autopilots
Mount the autopilot near the centre of gravity with the arrow forward on the supplied foam or damping mount. Never power the servo rail from the power module; use a separate BEC if servos need power.
| CUAV, CubePilot, SIYI, RadioLink and Indian-made autopilots pin | Port on the autopilot | Note |
|---|---|---|
| Power module | POWER1 | Battery through the PM to the PDB |
| GPS | GPS1 | Arrow forward, away from wires |
| Receiver | RC IN | SBUS or CRSF (set SERIAL protocol) |
| ESCs | MAIN OUT 1 to 4 (or FMU outputs) | Signal and GND only |
| Telemetry | TELEM1 | Air radio |
- Power module
- Port on the autopilot:
- POWER1
- Note:
- Battery through the PM to the PDB
- GPS
- Port on the autopilot:
- GPS1
- Note:
- Arrow forward, away from wires
- Receiver
- Port on the autopilot:
- RC IN
- Note:
- SBUS or CRSF (set SERIAL protocol)
- ESCs
- Port on the autopilot:
- MAIN OUT 1 to 4 (or FMU outputs)
- Note:
- Signal and GND only
- Telemetry
- Port on the autopilot:
- TELEM1
- Note:
- Air radio
Example code
PX4 users do the same in QGroundControl. Re-do the compass calibration whenever wiring near the GPS changes. PDRL and Naza use their own configuration software.
1. Connect USB, Setup > Install Firmware > pick Copter, Plane or Rover
2. Mandatory Hardware:
Frame Type -> e.g. Quad X
Accel Calibration -> level, left, right, nose down, nose up, back
Compass -> Start, rotate the drone in all directions
Radio Calibration -> move all sticks and switches to their ends
Flight Modes -> Stabilize, AltHold, Loiter, RTL on a 3- or 6-way switch
ESC Calibration -> props off, follow the on-screen steps
Failsafe -> battery and radio failsafe to RTL or Land
3. Config > Full Parameter List: SERIAL1_PROTOCOL = 2 (MAVLink2) for telemetry
4. Test arm with props OFF, then hover test in an open fieldSetup and tuning
install ArduPilot or PX4 with Mission Planner or QGroundControl.
calibrate the accelerometer, compass and radio before first flight.
use the matching power module for clean supply and battery monitoring.
mount the GPS mast away from power wires and set its orientation.
set radio, battery and GCS failsafes before flying.
What you need
Shop this list18 of 20 found in our store · ₹6,44,402
CUAV Pixhawk V6X V2 Flight Controller: the part this guide coversCUAV Pixhawk V6X V2 Flight Controller₹43,948
CUAV V6X Flight Controller: another version this guide coversCUAV V6X Flight Controller₹29,999
CUAV Nora+ Flight Controller: another version this guide coversCUAV Nora+ Flight Controller₹47,249
CUAV X7+ Flight Controller | Autopilot For PX4 & APM Drone Hardware: another version this guide coversCUAV X7+ Flight Controller | Autopilot For PX4 & APM Drone Hardware₹29,209
CUAV X7+ Pro Flight Controller | Autopilot for PX4 APM Drone Quadcopter Pixhawk: another version this guide coversCUAV X7+ Pro Flight Controller | Autopilot for PX4 APM Drone Quadcopter Pixhawk₹92,049
CUAV X25 EVO Pixhawk Autopilot Flight Controller: another version this guide coversCUAV X25 EVO Pixhawk Autopilot Flight Controller₹46,719- CubePilot Cube OrangeRX+ (IMU only) Flight Controller: another version this guide coversFind this part
- CubePilot Cube OrangeRX+ Standard Set ADS-B: another version this guide coversFind this part
SIYI N7 Autopilot Flight Controller with 2-14S Power Module: another version this guide coversSIYI N7 Autopilot Flight Controller with 2-14S Power Module₹41,159
SIYI N7 Autopilot Flight Controller with 2-14S Power Module & GPS: another version this guide coversSIYI N7 Autopilot Flight Controller with 2-14S Power Module₹41,159
RadioLink PIX6 Flight Controller: another version this guide coversRadioLink PIX6 Flight Controller₹16,496
RadioLink Mini Pix Flight Controller: another version this guide coversRadioLink Mini Pix Flight Controller₹8,088
RadioLink Pixhawk Flight Controller Board: another version this guide coversRadioLink Pixhawk Flight Controller Board₹14,796
RadioLink CrossFlight Flight Controller: another version this guide coversRadioLink CrossFlight Flight Controller₹6,359
Syncore U1 High Performance Flight Controller: another version this guide coversSyncore U1 High Performance Flight Controller₹13,900
HC Robotics HCR-504B Flight Controller (Autopilot): another version this guide coversHC Robotics HCR-504B Flight Controller (Autopilot)₹49,159
Omni Mini Autopilot Drone Flight Controller – Made in India: another version this guide coversOmni Mini Autopilot Drone Flight Controller – Made in India₹15,184
PDRL Ag++ Flight Controller + NamoAG Navigation Module with AeroGCS Software Stack: another version this guide coversPDRL Ag++ Flight Controller + NamoAG Navigation Module with AeroGCS Software Stack₹48,038
VECROS JETCORE Flight Controller Board: another version this guide coversVECROS JETCORE Flight Controller Board₹96,500
RCTimer ATLAS Flight Control System with GPS and LED Module: another version this guide coversRCTimer ATLAS Flight Control System with GPS and LED Module₹4,391
Alternatives and when to choose them
- Holybro Pixhawk 6X and 6C: the main alternative.
- Pixhawk 2.4.8 and APM clones: low-cost learning boards.
- Heavy-lift ESCs: for ag drones.
Common mistakes to avoid
- Flying without setting failsafes.
- Skipping compass calibration after mounting the GPS.
- Powering the autopilot from a noisy ESC BEC.
- Ignoring pre-arm errors.
Frequently asked questions
Should I choose ArduPilot or PX4?
ArduPilot has more vehicle types and setup guides; PX4 is popular in research. Both run on these boards.
Why does my autopilot refuse to arm?
Pre-arm checks fail. Read the message in the ground station, often calibration or GPS.
Do I need a safety switch?
Most setups expect one; it can be disabled in parameters.
What does a triple IMU do?
Redundant IMUs let the autopilot switch sensors if one fails.
Can I connect a companion computer?
Yes. Connect a Pi or Jetson to a telemetry port using MAVLink.
Parts for this guide
Keep learning
Sources
Written by the Geekobot team from manufacturer datasheets. Always check the datasheet for the exact part and variant you buy.








