Component guide · Advanced · 3 min read
CubePilot Here4 Multiband RTK, Here4 Blue, Here3+ RTK, Here+ RTK Base

and ADS-B Carrier Board
By Geekobot Learning Team · Updated 29 Oct 2026
On this page
CubePilot's Here units are DroneCAN GPS and compass modules made for the Cube autopilots. The Here4 is multiband (L1 and L5) for faster, more robust fixes and RTK; the Here3+ uses an M8P for RTK; the Here+ base sends corrections from the ground. The ADS-B carrier board adds a 1090 MHz receiver so the drone sees manned aircraft nearby.
Key specs at a glance
- GNSS
- u-blox F9P multiband (Here4), M8P (Here3+, Here+)
- Accuracy
- About 1 to 2 cm with RTK; metres without
- Interface
- DroneCAN (Here3+, Here4); USB for base
- Compass
- Built in, with IMU on Here4
- Supply
- 5 V from CAN port
- ADS-B
- 1090 MHz receiver on carrier board
Models in this guide
These are alternatives. Pick the one that fits your project; you only need one.
Option 1CubePilot Here4 Multiband RTK GNSS Module₹44,099
Option 2CubePilot Here4 Blue Multiband RTK GNSS w/ NRF 2.4GHz Radio₹38,589
Option 3CubePilot Here3+ RTK GNSS Module w/ iStand₹41,949
Option 4CubePilot HERE3+ GNSS M8P RTK GPS Module₹81,339
Option 5CubePilot Here+ RTK Centimeter-Level GNSS Base Module₹18,899
Option 6CubePilot ADSB Carrier Board – 1090MHz ADS-B Receiver₹20,756
What the CubePilot Here3+, Here4 and ADS-B carrier is
CubePilot Here GNSS modules give Cube and other autopilots position, compass and safety LED in one unit, with RTK versions for centimetre accuracy.
RTK needs a base station sending corrections, either your own Here+ base over the telemetry radio or an NTRIP service over the internet through the ground station.
Here4 Blue adds an nRF radio for remote ID and Bluetooth features. Check CubePilot docs for firmware updates through Mission Planner.
CubePilot Here3+, Here4 and ADS-B carrier pinout
The pins on the CubePilot Here3+, Here4 and ADS-B carrier and what each one does.
| Pin | Function |
|---|---|
| CAN | 4-pin DroneCAN (5 V, CAN H, CAN L, GND) |
| USB | Base station (Here+) |
| LED | Status |
- CAN
- 4-pin DroneCAN (5 V, CAN H, CAN L, GND)
- USB
- Base station (Here+)
- LED
- Status
Wiring the CubePilot Here3+, Here4 and ADS-B carrier
Use the supplied CAN cable; no UART wiring is needed.
| CubePilot Here3+, Here4 and ADS-B carrier pin | Item | Connect to | Notes |
|---|---|---|---|
| CAN cable | Cube CAN1 port | Cube CAN1 port | |
| Here+ base USB | Ground station PC | Ground station PC | |
| ADS-B carrier | Cube carrier board | Cube carrier board |
- CAN cable
- Item:
- Cube CAN1 port
- Connect to:
- Cube CAN1 port
- Here+ base USB
- Item:
- Ground station PC
- Connect to:
- Ground station PC
- ADS-B carrier
- Item:
- Cube carrier board
- Connect to:
- Cube carrier board
Example code
For NTRIP, enter the caster details in the same RTK/GPS Inject page instead of using a base.
1. CAN_P1_DRIVER = 1, GPS1_TYPE = 9 (DroneCAN). Reboot.
2. Base: plug the Here+ base into the PC, Mission Planner > Setup > Optional > RTK/GPS Inject.
3. Run survey-in (e.g. 2 m accuracy, 60 s) or enter a known position.
4. Corrections go to the drone over the telemetry link; status should show RTK Float then RTK Fixed.Setup and tuning
connect Here3+ and Here4 to the CAN port and enable DroneCAN GPS and compass in parameters.
use a Here+ base or NTRIP to send RTCM corrections through the ground station.
mount on a mast with the arrow pointing forward, away from power wires.
calibrate after mounting.
update the Here4 firmware through the ground station.
What you need
Shop this list9 of 9 found in our store · ₹2,96,495
CubePilot Here4 Multiband RTK GNSS Module: the part this guide coversCubePilot Here4 Multiband RTK GNSS Module₹44,099
CubePilot Here4 Blue Multiband RTK GNSS w/ NRF 2.4GHz Radio: another version this guide coversCubePilot Here4 Blue Multiband RTK GNSS w/ NRF 2.4GHz Radio₹38,589
CubePilot Here3+ RTK GNSS Module w/ iStand: another version this guide coversCubePilot Here3+ RTK GNSS Module w/ iStand₹41,949
CubePilot HERE3+ GNSS M8P RTK GPS Module: another version this guide coversCubePilot HERE3+ GNSS M8P RTK GPS Module₹81,339
CubePilot Here+ RTK Centimeter-Level GNSS Base Module: another version this guide coversCubePilot Here+ RTK Centimeter-Level GNSS Base Module₹18,899
CubePilot ADSB Carrier Board – 1090MHz ADS-B Receiver: another version this guide coversCubePilot ADSB Carrier Board – 1090MHz ADS-B Receiver₹20,756
Holybro Pixhawk 6C flight controller: the autopilot these modules plug intoHolybro Pixhawk 6C Flight Controller + PM02 Power Module₹36,439Closest match, check the specs
Holybro SiK telemetry radio V3 433 MHz: to send RTK corrections to the droneHolybro Sik Telemetry Radio V3 100 mW 433 MHz₹9,949Closest match, check the specs
Raspberry Pi 4 Model B (4 GB): to run an RTK base, NTRIP or loggingRaspberry Pi 4 Model B 1GB RAM₹4,476Closest match, check the specs
Alternatives and when to choose them
- Holybro H-RTK: F9P RTK for Pixhawk.
- CUAV C-RTK: another RTK family.
- Pixhawk GPS modules: non-RTK units.
Common mistakes to avoid
- Leaving DroneCAN disabled.
- Mounting the module with the arrow pointing the wrong way.
- Mounting the GPS near the power module or ESCs.
- Skipping compass calibration.
Frequently asked questions
Do I need RTK for normal flying?
No. Without corrections the module gives normal GPS accuracy of a few metres.
Why does my autopilot not see the Here4?
Enable DroneCAN on the CAN port and set the GPS type to DroneCAN in parameters.
What is Here4 Blue?
A version made in the USA for projects with supply-chain requirements.
Can I use Here4 on a non-Cube autopilot?
Yes, on autopilots with a CAN port running ArduPilot or PX4.
What is the ADS-B carrier board?
A Cube carrier with an ADS-B receiver to detect nearby manned aircraft.
Parts for this guide
Keep learning
Sources
Written by the Geekobot team from manufacturer datasheets. Always check the datasheet for the exact part and variant you buy.


