Component guide · Advanced · 3 min read
CUAV C-RTK 2, C-RTK 2 HP Dual-Antenna Heading and C-RTK 9Ps Base

and Rover RTK GNSS Modules
By Geekobot Learning Team · Updated 29 Oct 2026
On this page
CUAV's C-RTK modules give centimetre positioning for survey and agricultural drones. The C-RTK 2 supports RTK and PPK (post-processing) for mapping; the C-RTK 2 HP uses two antennas to measure heading without a compass; and the C-RTK 9Ps comes as base and rover units. They connect to Pixhawk and CUAV autopilots over UART or CAN.
Key specs at a glance
- Receiver
- Multiband RTK GNSS
- Accuracy
- About 1 cm + 1 ppm (RTK)
- Heading
- Dual antenna on C-RTK 2 HP
- Modes
- RTK and PPK
- Interface
- UART or CAN to the autopilot
- Kit
- Base and rover units for 9Ps
Models in this guide
These are alternatives. Pick the one that fits your project; you only need one.
Option 1CUAV C-RTK 2 High Precision RTK PPK GNSS Module₹75,749
Option 2CUAV C-RTK 2 HP GNSS Heading Module w/ Dual Antenna₹44,249
Option 3CUAV C-RTK 9Ps Positioning Module | High Precision GPS RTK GNSS for Pixhawk₹94,243
Option 4CUAV C-RTK 9Ps Positioning Module – Base Unit Only₹59,289
Option 5CUAV C-RTK 9Ps Positioning Module – Rover Unit₹31,099
Option 6CUAV C-RTK 9Ps Rover – Air Unit (Without Stand)₹70,783
What the CUAV C-RTK 2 and C-RTK 9Ps is
CUAV C-RTK modules are RTK GNSS receivers that give drones centimetre-level positioning, with dual-antenna heading and base and rover kits.
PPK records raw data on the drone and corrects it later against a base log, useful when the radio link drops during mapping.
Dual-antenna heading needs the two antennas a set distance apart and aligned with the drone's axis.
CUAV C-RTK 2 and C-RTK 9Ps pinout
The pins on the CUAV C-RTK 2 and C-RTK 9Ps and what each one does.
| Pin | Function |
|---|---|
| GPS port | UART and I2C |
| CAN | Some models |
| Antenna | SMA or integrated |
| USB | Configuration |
- GPS port
- UART and I2C
- CAN
- Some models
- Antenna
- SMA or integrated
- USB
- Configuration
Wiring the CUAV C-RTK 2 and C-RTK 9Ps
Connect the CUAV C-RTK 2 and C-RTK 9Ps like this.
| CUAV C-RTK 2 and C-RTK 9Ps pin | Flight controller (Pixhawk) | Flight controller (Betaflight / INAV) |
|---|---|---|
| 5V | Flight controller GPS port 5 V | Flight controller GPS port 5 V |
| GND | GND | GND |
| TX | FC UART RX | FC UART RX |
| RX | FC UART TX | FC UART TX |
| SDA / SCL | FC I2C (compass) | FC I2C (compass) |
- 5V
- Flight controller (Pixhawk):
- Flight controller GPS port 5 V
- Flight controller (Betaflight / INAV):
- Flight controller GPS port 5 V
- GND
- Flight controller (Pixhawk):
- GND
- Flight controller (Betaflight / INAV):
- GND
- TX
- Flight controller (Pixhawk):
- FC UART RX
- Flight controller (Betaflight / INAV):
- FC UART RX
- RX
- Flight controller (Pixhawk):
- FC UART TX
- Flight controller (Betaflight / INAV):
- FC UART TX
- SDA / SCL
- Flight controller (Pixhawk):
- FC I2C (compass)
- Flight controller (Betaflight / INAV):
- FC I2C (compass)
Example code
A minimal sketch to check the part works.
ArduPilot (4.4 or later), GPS on SERIAL3 (GPS1 port):
SERIAL3_PROTOCOL = 5 GPS
GPS1_TYPE = 1 Auto (u-blox) [DroneCAN modules: GPS1_TYPE = 9, CAN_P1_DRIVER = 1]
COMPASS_ENABLE = 1 and run compass calibration in the ground station
PX4: GPS_1_CONFIG = GPS 1, then calibrate the compass.
Betaflight / INAV: enable GPS on the UART in Ports, protocol UBLOX, baud auto.
RTK: send base corrections through the ground station (RTK/GPS Inject).Setup and tuning
set up a base station on a fixed point, or use an NTRIP correction service.
send RTCM corrections to the drone through the telemetry radio or ground station.
mount the two antennas apart along the frame and set the offset in the autopilot.
place the antennas clear of carbon and other electronics.
let the base survey its position before flights, or enter a known position.
What you need
Shop this list9 of 9 found in our store · ₹4,26,276
CUAV C-RTK 2 High Precision RTK PPK GNSS Module: the part this guide coversCUAV C-RTK 2 High Precision RTK PPK GNSS Module₹75,749
CUAV C-RTK 2 HP GNSS Heading Module w/ Dual Antenna: another version this guide coversCUAV C-RTK 2 HP GNSS Heading Module w/ Dual Antenna₹44,249
CUAV C-RTK 9Ps Positioning Module | High Precision GPS RTK GNSS for Pixhawk: another version this guide coversCUAV C-RTK 9Ps Positioning Module | High Precision GPS RTK GNSS for Pixhawk₹94,243
CUAV C-RTK 9Ps Positioning Module – Base Unit Only: another version this guide coversCUAV C-RTK 9Ps Positioning Module – Base Unit Only₹59,289
CUAV C-RTK 9Ps Positioning Module – Rover Unit: another version this guide coversCUAV C-RTK 9Ps Positioning Module – Rover Unit₹31,099
CUAV C-RTK 9Ps Rover – Air Unit (Without Stand): another version this guide coversCUAV C-RTK 9Ps Rover – Air Unit (Without Stand)₹70,783
Holybro Pixhawk 6C flight controller: the autopilot these modules plug intoHolybro Pixhawk 6C Flight Controller + PM02 Power Module₹36,439Closest match, check the specs
Holybro SiK telemetry radio V3 433 MHz: to send RTK corrections to the droneHolybro Sik Telemetry Radio V3 100 mW 433 MHz₹9,949Closest match, check the specs
Raspberry Pi 4 Model B (4 GB): to run an RTK base, NTRIP or loggingRaspberry Pi 4 Model B 1GB RAM₹4,476Closest match, check the specs
Alternatives and when to choose them
- Holybro H-RTK: F9P RTK.
- Here4: CubePilot multiband RTK.
- Pixhawk GPS: standard GPS.
Common mistakes to avoid
- Flying before the base finishes its survey.
- Mounting antennas next to carbon or power wires.
- Not setting antenna offsets for dual-antenna heading.
- Using a slow corrections link that drops messages.
Frequently asked questions
Do I need a base station for RTK?
Yes, or an NTRIP service. RTK needs correction data from a reference point.
What accuracy can I expect?
About 1 to 2 cm with an RTK fix; metres without corrections.
What does dual-antenna heading do?
It gives heading from GNSS, so the drone does not depend on the compass.
Can I use it with ArduPilot?
Yes. ArduPilot and PX4 support CUAV RTK modules.
Why does my drone only get float, not fix?
Weak corrections, poor sky view or a long baseline. Check the link and antenna placement.
Parts for this guide
Keep learning
Sources
Written by the Geekobot team from manufacturer datasheets. Always check the datasheet for the exact part and variant you buy.


