Buying guide · Advanced · 3 min read
Pixhawk and ArduPilot Autopilots
Cube, Holybro and What You Need to Fly
By Geekobot Learning Team · Updated 29 Oct 2026
On this page
Pixhawk-class autopilots run ArduPilot or PX4 and support GPS missions, return-to-home, failsafes and many vehicle types. Newer controllers such as the Cube series and Holybro Pixhawk 6C replace the old 2.4.8 boards. You also need a GPS and compass, a power module, a safety switch, a radio receiver and optionally telemetry radios. Calibrate before the first flight.
Key specs at a glance
- Firmware
- ArduPilot (copter, plane, rover, sub) or PX4
- Ground station
- Mission Planner (Windows) or QGroundControl
- Core hardware
- Flight controller, GPS with compass, power module, safety switch, buzzer
- Radio
- PPM, SBUS, CRSF or ELRS receiver
- Telemetry
- SiK radio pair or WiFi link
- Buses
- CAN (DroneCAN), I2C, UART, PWM outputs
Which controller
Pixhawk hardware has evolved. Choose by quality, support and vehicle size.
| Controller | Notes | Good for |
|---|---|---|
| Pixhawk 2.4.8 / 2.4.7 kits | Older clones; cheap; limited processing and support | Learning and small builds |
| CubePilot Cube Orange / Cube+ | Vibration-isolated, redundant IMUs, carrier boards | Professional and heavy-lift builds |
| Holybro Pixhawk 6C / 6X | Modern STM32H7, tidy connectors, good community support | General purpose and long range |
| Small H7 FCs (Kakute etc.) | Compact with ArduPilot support | Smaller aircraft |
- Pixhawk 2.4.8 / 2.4.7 kits
- Notes:
- Older clones; cheap; limited processing and support
- Good for:
- Learning and small builds
- CubePilot Cube Orange / Cube+
- Notes:
- Vibration-isolated, redundant IMUs, carrier boards
- Good for:
- Professional and heavy-lift builds
- Holybro Pixhawk 6C / 6X
- Notes:
- Modern STM32H7, tidy connectors, good community support
- Good for:
- General purpose and long range
- Small H7 FCs (Kakute etc.)
- Notes:
- Compact with ArduPilot support
- Good for:
- Smaller aircraft
What you need to fly
- 1Autopilot and a power module (voltage and current sensing).
- 2GPS and compass on a mast; see the GPS guide.
- 3Radio and receiver; see choosing a transmitter.
- 4ESCs and motors for your frame, with the right output protocol (DShot or PWM).
- 5Telemetry for ground station connection.
- 6Safety switch and buzzer, which are standard parts of the kit.
Setup steps
- 1Install the ground station and flash the firmware for your vehicle.
- 2Choose the frame type and run the mandatory hardware setup.
- 3Calibrate accelerometer, compass and radio.
- 4Configure flight modes: Stabilize, AltHold, Loiter, RTL and Auto.
- 5Set battery monitor and failsafe actions.
- 6Check the ESC calibration, motor order and direction with props off.
- 7Make the first flight in Stabilize, then Loiter once GPS has a good lock.
Safety and good practice
Always arm with props off for bench tests. Use geofence and return-to-launch settings, keep a manual override switch on the radio, and read the pre-arm messages: they exist to stop unsafe flights. Update firmware only from the official channels. Follow your country's drone rules; in India, check the Drone Rules and register where required.
Try it: Lipo drone flight time calculator
Change the values and the diagram and results update as you type.
Common mistakes to avoid
- Skipping compass calibration or mounting the compass near power wires.
- Ignoring pre-arm check failures.
- Powering the controller from a weak BEC.
- Mixing PWM and DShot ESC settings.
- Flying in Loiter before GPS lock is stable.
Frequently asked questions
ArduPilot or PX4?
Both are open source. ArduPilot supports more vehicle types and parameters; PX4 has a cleaner architecture for developers.
Is a Pixhawk 2.4.8 still worth buying?
It works for learning but newer H7 boards have better processors, sensors and support.
Do I need telemetry?
It is very useful for live data and parameter changes, but you can also fly with only a radio.
What is DroneCAN?
A CAN-based protocol for GPS, ESCs and peripherals that reduces wiring.
Can it fly planes and rovers?
Yes, ArduPilot supports planes, rovers, boats and submarines.
Parts for this guide
Calculators
Terms in this guide
Projects that use it
Put this into practice: 1 step-by-step build in our project library uses parts from this guide.
Keep learning
Sources
Written by the Geekobot team from manufacturer datasheets. Always check the datasheet for the exact part and variant you buy.




