Component guide · Advanced · 3 min read
Holybro PM02D, PM03D, PM06, PM07, PM08-CAN

and CUAV CAN PMU Digital Power Modules
By Geekobot Learning Team · Updated 29 Oct 2026
On this page
Digital power modules measure battery voltage and current with an onboard ADC and report over I2C or DroneCAN, giving more accurate readings than analog modules. Holybro PM02D and PM03D suit Pixhawk 5X/6X/6C; PM06 and PM07 add PDB functions for up to 14S; PM08-CAN reports over CAN at 200 A. CUAV's CAN PMU and CAN PDB do the same for CUAV autopilots.
Key specs at a glance
- Interfaces
- I2C (PM02D, PM03D, PM06, PM07) or DroneCAN (PM08-CAN, CUAV)
- Input
- 2S to 12S/14S
- Current
- 60 A to 200 A
- Autopilot supply
- 5.2 to 5.4 V
- PDB
- PM03D, PM06, PM07 include ESC pads
- Calibration
- Factory, usually no tuning needed
Models in this guide
These are alternatives. Pick the one that fits your project; you only need one.
Option 1Holybro PM02D Power Module High Voltage (2S-12S)₹3,481
Option 2Holybro PM03D Power Module₹5,559
Option 3Holybro PM03D Power Module (Without XT30 Pre-soldered)₹6,959
Option 4Holybro PM06 V2 Power Module – 2S-14S, 70A Continuous₹3,059
Option 5Holybro PM06D Power Module (14S)₹4,009
Option 6Holybro PM07 Power Module (14S)₹5,249
What the Holybro digital power module is
The Holybro digital power modules, such as the PM02D and PM03D, measure battery voltage and current over I2C and give a clean 5.2 V supply to a Pixhawk autopilot.
Match the module to the autopilot: Pixhawk 6X and 6C use I2C digital modules on POWER1; CAN modules need DroneCAN enabled.
PM07 and PM03D double as power distribution boards with ESC pads, saving weight on medium frames.
Holybro digital power module pinout
The pins on the Holybro digital power module and what each one does.
| Pin | Function |
|---|---|
| Battery input | XT60/XT90 or pads |
| ESC outputs | Pads (PDB versions) |
| Power port | 6-pin I2C or 4-pin CAN |
| Aux 5 V / 12 V | Some versions |
- Battery input
- XT60/XT90 or pads
- ESC outputs
- Pads (PDB versions)
- Power port
- 6-pin I2C or 4-pin CAN
- Aux 5 V / 12 V
- Some versions
Wiring the Holybro digital power module
Connect the Holybro digital power module like this.
| Holybro digital power module pin | I2C modules | CAN modules |
|---|---|---|
| Power port | Pixhawk POWER1 (I2C) | CAN1 port |
| ESC pads | Quad or hex ESCs | Same |
- Power port
- I2C modules:
- Pixhawk POWER1 (I2C)
- CAN modules:
- CAN1 port
- ESC pads
- I2C modules:
- Quad or hex ESCs
- CAN modules:
- Same
Example code
A minimal sketch to check the part works.
PX4: SENS_EN_INA226 = 1 (PM02D/PM03D/PM06)
ArduPilot: BATT_MONITOR = 21 (INA2xx) or 8 (DroneCAN)
Reboot after changes.Setup and tuning
use with autopilots that support digital (I2C) power modules, such as the Pixhawk 5X and 6X.
battery to the input, ESCs or PDB to the output, and the 6-pin cable to the POWER port.
check voltage (2S to 12S on PM02D) and current ratings for your drone.
set the battery monitor to the digital power module type in QGroundControl or Mission Planner.
compare voltage and current with a meter and adjust the scales.
What you need
Shop this list11 of 11 found in our store · ₹65,945
Holybro PM02D Power Module High Voltage (2S-12S): the part this guide coversHolybro PM02D Power Module High Voltage (2S-12S)₹3,481
Holybro PM03D Power Module: another version this guide coversHolybro PM03D Power Module₹5,559
Holybro PM03D Power Module (Without XT30 Pre-soldered): another version this guide coversHolybro PM03D Power Module₹5,559
Holybro PM06 V2 Power Module – 2S-14S, 70A Continuous: another version this guide coversHolybro PM06 V2 Power Module – 2S-14S, 70A Continuous₹3,059
Holybro PM06D Power Module (14S): another version this guide coversHolybro PM06D Power Module (14S)₹4,009
Holybro PM07 Power Module (14S): another version this guide coversHolybro PM07 Power Module (14S)₹5,249
Holybro PM08-CAN Power Module 14S, 200A: another version this guide coversHolybro PM08-CAN Power Module 14S, 200A₹9,058
CUAV CAN PMU Autopilot Power Module: another version this guide coversCUAV CAN PMU Autopilot Power Module₹13,465
CUAV CAN PDB Multifunctional Autopilot Baseboard: another version this guide coversCUAV CAN PDB Multifunctional Autopilot Baseboard₹15,679
Digital multimeter: to check supply and signal voltagesDigital Multimeter₹177
Digital watt meter and power analyser: to measure pack currentDigital Watt Meter and Power Analyser₹650
Alternatives and when to choose them
Common mistakes to avoid
- Using a digital module on an analog-only autopilot.
- Powering servos from the module.
- Skipping calibration.
- Exceeding the current rating.
Frequently asked questions
Does the PM02D work with all Pixhawks?
Only with autopilots that support digital power modules, such as Pixhawk 5X and 6X.
Why is the battery voltage wrong in QGroundControl?
The battery monitor type is wrong or not calibrated.
Can the power module supply servos?
No. It powers only the autopilot; use a separate BEC for servos.
What current can the PM02D measure?
Up to about 120 A continuous, depending on version.
Why use a digital power module?
It sends accurate readings over I2C, with less noise than analog.
Parts for this guide
Keep learning
Sources
Written by the Geekobot team from manufacturer datasheets. Always check the datasheet for the exact part and variant you buy.
